rough country SOFT ROLL UP TRUCK BED COVER User manual

-1-
WARRANTY
1. Do not place objects on or against cover or framework.
2. Do not tie cargo to cover framework.
3. Neverallowchildren or pets to occupy pickup box while
cover is closed.
4. Cover is not airtight. Special care is required to keep
cargo clean and dry.
5. Fabriccoverwon’tpreventtheftofcontentsinsidetruck
box.
6. Covermustberolledfullyopenandsecuredwithretainer
straps when towing vehicle backwards.
7. Openedcovermustbesecuredwith bothretainerstraps
when driving vehicle.
8. Cover must NEVER be rolled partially open while
operating vehicle.
It is the responsibility of the owner/user to read this manual and
comply with the operating procedures. The owner/user is also
responsible for inspecting their truck bed cover system, and for
having parts repaired or replaced when worn or damaged.
Failuretofollowsafetyinstructionsandwarninglabelscouldresult
in failure of your cover system and/or personal injury.
• Always wear safety glasses and/or other necessary protective
equipment when installing your truck bed cover system.
• These instructions are complete for most pickup models.
Additional instructions are included, if required for your pickup.
Please read entire manual before installing your truck bed cover
system.
Vinylcovercanbehandwashedwithmildsoapandwaterorcleaned
inacarwash. Thoroughlyrinsecovertoremoveanysoapresidue.
Cover can be treated with any vinyl protectant made for ttruck bed
covers. Never use any vinyl conditioners (ie, Armor
All®) that contain silicone, petroleum, or citrus
based products on your truck bed cover as they
may crack and shrink the vinyl.
COVER MAINTENANCE
MESSAGES TO INSTALLER
OWNER/USER RESPONSIBILITIES
SOFT ROLL UP TRUCK BED COVER
DIRECTALL WARRANTY CLAIMS TO:
WARNING
Tighten clamps securely on side rails before driving
vehicle, to prevent cover from blowing off.
!
9. Covermustberolledfullyopenandsecuredwithretainer
straps if any part of the truck bed cover is worn or
damaged.
ATTENTION!
P/N 1118517 Rev P2
Our company warrants this product to be free of defects in
material and workmanship at the time of purchase by the
original retail consumer. We disclaim any other warranties,
express or implied, including the warranty of tness for
a particular purpose or an intended use. If the product is
found to be defective, we may replace or repair the product
at our option, when the product is returned prepaid, with
the proof of purchase. Alteration to, improper installation, or
misuse of this product voids the warranty. Our company’s
liability is limited to repair or replacement of products found
to be defective, and specically excludes liability for any
incidental or consequential loss or damage.
Before returning any item please call
1-800-222-7023 or email:
[e-mail] to receive instructions
and Return Goods Authorization (RGA) number.
Please have your order number and full contact in-
formation available, along with the reason for your
return.

-2-
Components
A
BCD
Tools Required
9/16”
6x
3:
Correct
2:
B
F
1:
E
G
2x
2x
1/2”
SOFT ROLL-UP TRUCK BED COVER
MANUAL
H2x
2x

-3-
B
4:
Tighten clamps securely on
side rails before driving vehicle.
WARNING
!
LEVEL
5:
B
6: Repeat steps 3-5 on passenger side for item C. Proceed to step 7 when complete.
1/2”
SETTING TENSION ADJUSTMENT BLOCKS
7: Adjustment Zone
Cover tension is controlled by four position adjustable blocks.
To start, place blocks in postion shown below. With 4 on top and
closest to front header. Secure blocks with hitchpin in #2 hole,
this is the least amount of tension. (Position 4)
Hitchpin
Position 1
Maximum
Position 2
Position 3
Position 4
Minimum
Setting cover tension
1. Set cover tension during warmest part of the day.
2. Roll cover up to adjustable block.
3. Pull Hitchpin and rotate blocks to the next position need-
ed. Replace Hitchpin. (Driver and passenger blocks
must always be in the same position.)
4. Close cover and re-check adjustment. Repeat until sat-
isfactory tension has been achieved.
When installing clamps, nger tighten nut holding back side of clamp. Be sure the teeth of
the clamp engage with the grooves of the side rail. Holding the clamp, tighten the nut not
allowing the clamp to rotate.
End Seal Compressed At Cab.
End Seal Compressed At
Tailgate.
With Tailgate Closed, Position Side Rail Compressing End Seals
Equally Between Cab and Tailgate.

-4-
B
9: Thread nut onto bolt enough to be tight but still able to move freely. DO NOT over tighten nut and plastic
washer connection.
BUnhook and unroll cover to the tailgate.
10:
9/16” 9/16”
8:
A
E
F
Passenger side detailDrivers side detail

-5-
B
B
B
!
CAUTION
ROLL COVER TIGHT AND SECURE BOTH RETAINER
STRAPS.DONOTSTOWCOVERAGAINSTCABWINDOW.
To unlatch Pull Toggle.
14:
To stow cover open roll cover to the front. Secure both hooks
DO NOT stow cover against cab window.
13: NOTE: Secure hook fastener and loop fastener along entire length
of both side rails before driving vehicle. This will prevent wind lifting
the cover and causing damage.
15:
B
B
NOTE:Preferred method to close cover. Roll cover closed
then close tailgate. Seal will be inside the tailgate. If tailgate
has a key lock, truck bed cover is secured until tailgate is
unlocked and opened.
12:
11:
A
A
CLICK

-6-
12 * Hook Strip
13 1703332 Hitch Pin
14 1705234 ClampAssembly (6)
15 * Side Rail, Passenger’s Side
16 * Side Rail, Driver’s Side
17 1114773 Flat Spring
18 1704213 LatchAssembled
19 1703455 Cap Screw
20 1705336 Header Stop
21 1703690 Self Drill Screw
22 1705405 Rear Header End Plug RH
23 1705404 Rear Header End Plug LH
24 * Rear Header
25 1117958 Side Rail End PlugAssy LH
26 1117959 Side Rail End PlugAssy RH
27 1701580 Hex Nut Full Nylon Lock
28 * Extruded Header Seal
* Please specify length or make and model of vehicle.
1* Replacement Cover
2* Front Header
31705310 Front Header End Plug RH
41705311 Front Header End Plug LH
5* Retainer Strap
61115745 Plastic Washer
71703455 Square Head Cap Screw
8* BowAssembly
91705192 Retainer Loop
10 1705318 Tension Adjustment Block
11 1705364 Header Insert Retainer Clip
REPLACEMENT PARTS
1
2
4
3
56
7
810
11
11
12
13
14
15
16
17
18
19
20
21
22
23
25
26
24
27
25
28
28
2
9
28
8
26