rough country 927061900 User manual

2016 Tacoma 30” Single Row LED Bumper Mount
927061900
Thank you for choosing Rough Country for all your lighting needs.
Please read instructions before beginning installation. Check the kit hardware against the kit contents
shown below. Be sure you have all needed parts and know where they go.
If question exist, please call us @1-800-222-7023. We will be happy to answer any questions concerning the design,
function, and correct use of our products.
Only fits Toyota Tacoma 2016 models.
By purchasing any item sold by Rough Country, LLC, the buyer expressly warrants that he/she is in compliance with all
applicable Federal, State, and Local laws and regulations regarding the purchase, ownership, and
use of the item. It shall be the buyers responsibility to comply with all Federal, State and Local laws
governing the sales of any items listed, illustrated or sold. The buyer expressly agrees to indemnify
and hold harmless Rough Country, LLC for all claims resulting directly or indirectly from the purchase,
ownership, or use of the items.
Tools Needed:
14mm Wrench
Reciprocating Saw
Side Cutters
10mm Socket
Flat Screwdriver
Kit Contents:
2-Rough Country LED Light Brackets
1-70619BAG containing:
Instructions
1-70523BAG2 containing:
(2) 8mm Hex Head Stainless Bolts

1. Park the vehicle on a smooth level surface.
2. Using a 10mm socket, remove the (2) upper grille mount screws. See Photo 1.
3. Using a flat screwdriver, remove the (2) upper grille push pins. See Photo 2.
4. Reaching down behind the grille, use a flat screwdriver to release the lower clips holding the grille. See Photo 3.
5. Gently pull to remove the grille from the truck. See Photo 4.
6. Using a flat screwdriver, remove the (2) push pins holding the grille duct. See Photo 5.
7. Release the (2) clips from the radiator support that hold the grille duct. See Photo 6.
Photo 1 Photo 2
Photo 3 Photo 4
Photo 6 Photo 5
Remove upper grille mounts. Remove upper grille push pins.
Unclip lower grille. Remove grille.
Remove grille duct push pins. Unclip grille duct.

8. Gently pull to remove the grille duct from the truck. Repeat on opposite side of truck. See Photo 7.
9. Using a reciprocating saw, cut the vertical bars of the lower grille in the bumper and the horizontal bar on each end.
See Photo 8.
10. Remove the grille from the bumper. See Photo 9.
11. Measure over 1.5”and mark on the middle plastic part of the bumper. Do this on both sides of the bumper See
Photo 10.
13. Using a reciprocating saw, remove the plastic to the mark and file the edge smooth. Do this on both sides of the
bumper. See Photos 11 & 12.
Photo 8
Photo 10
Photo 7
Photo 9
Photo 11 Photo 12
Remove the grille duct. Cut bumper grille.
Remove bumper grille. Mark plastic for trimming.
Trim plastic in bumper center. File edge smooth.

14. Using a 14mm socket, remove the (2) bumper mounting bolts on each side of the truck . See Photo 13.
15. Insert light mounting brackets through hole in bumper. See Photos 14 & 15.
16. Using factory hardware, install the light mounting brackets on both sides of the truck. See Photo 16.
17. Using a 14mm socket tighten the factory nuts to factory torque specifications. See Photo 17.
18. Insert light into opening in bumper. See Photo 18.
Photo 18
Photo 13 Photo 14
Photo 15 Photo 16
Photo 17
Remove bumper mounting nuts. Insert light bracket into bumper opening.
Attach light mount to bumper mount.
Tighten bumper mounting nuts. Insert light into bumper opening.

19. Using supplied 8mm bolts and spacers (supplied with the light), install the light between the light mounts. See Photo
19.
20. Measure 6”from the bottom of the grille duct and mark. See Photo 20.
21. Using a reciporicating saw, cut the marked portion off of the grille duct. Repeat process for opposite side. See
Photo 21.
22. Install the grille duct parts back onto the truck. See Photo 22.
23. Install grille duct push pins. See Photo 23.
24. Install the grille back on the truck by gently pushing into place. See Photo 24.
Photo 20
Photo 22
Photo 24
Photo 21
Photo 23
Photo 19
Attach light to mounting brackets. Mark grille duct for cutting.
Cut grille duct. Install grille duct.
Insert grille duct push pins. Install grille.

25. Install grille push pins. See Photo 25.
26. Using a 10mm socket and factory bolts, attach the upper grille mounts to the truck. See Photo 26.
27. Make sure the lower portion of the grille is locked into place with the factory clips.. See Photo 27.
28. Wire light per instructions included with light.
Photo 28
Photo 27
Photo 25 Photo 26
Make sure factory clips are secure.
Replace grille push pins. Attach upper grille mounts.