RouterBOARD Cloud Core Series User manual

See www.routerboard.com fo r more information . Conta ct [e-mail]
21/08/13
Cloud Core Router series
Setup Guid e and Warrant y Information
The ROUTERBOARD is a h igh p erformance m ulticore r outer w ith t welve G igabit p orts and four SFP cages . Several models ar e
currentl y available: CloudCoreRouter 1036 --‐ 8G --‐ 2S+ (36 cores, 8x Gigabi t ports, 2x SFP+ ports), CloudCoreRouter 1036 --‐ 12G --‐ 4S
(36 cores, 12x Gigabit ports, 2x2GB RAM), CloudCoreRouter 1036 --‐ 12G --‐ 4S --‐ EM (32 cores, 12x Gigabi t ports, 2x8GB RAM),
CloudCoreRouter 1016 --‐ 12G (16 cores , 12x Gigabit ports, 2x1GB RAM) ,
First use
The device come s preinstalled with RouterOS a nd is ready t o use. Device is compatible with RouterOS v6 and newer, if your
device comes preinstalle d wit h a n earlier version, please upgrade before using it .
The Ethernet ports 1 has a default I P address for connecting: 192.168.88. 1 username is admin and ther e is no password .
Pleas e connect with your web browser to this I P address and choos e Webfig to configur e it. The device doesn’t have any
other configurati on applie d by default, please connect t o it, a nd set up WAN IP addresses, user password, firewall etc.
See this pag e for connection and configuration guides: http://wiki.mikrotik.com/wiki/Category:Manual
Powering
• 110~250 VAC
Extensio n Slot s and Ports
• 1036 --‐ 12G --‐ 4S and 1016 --‐ 12G : Twelve Gigabit Ethernet ports (Auto MDI/X) ; 1036 --‐ 8G --‐ 2S+ : Eight Gigabit ports
• 1036 --‐ 12G --‐ 4S : F our S FP c ages ; 1036 --‐ 8G --‐ 2S+ : Two SFP+ cages
• One LCD connector (LCD touchscreen included)
Resetting the device
In c ase y ou w ish t o r eturn t he d evice t o it s o rigina l c onfiguration , y ou c an use the RESET button. Hold this button during boo t
time until LED lights sta rt flashing, then release the button to reset RouterOS configuration. You can use this procedure if
you have forgotten the password to access the device, or simpl y wish to return the unit to its default configuration state.
Buttons and Jumpers
• RouterBOOT reset butt on (image R eset1 ) has several functions:
 Hold the button before powering on the device, and at power up, the button will force load the backup boot
loader . Continue holding the button for the other two functions o f this button:
 Release the butt on whe n gree n LED starts flashing, to rese t RouterOS configuration. To no t load backup boot
loader , y ou c an s tart h olding t he b utton a fter p ower i s a lready a pplied
 Release the butt on after LED is no longer flashing (~20 seconds ) to cause device to look fo r Netinstall servers
(required fo r reinstalling RouterOS ove r network)
• RouterOS reset jumper hole (image Reset2): reset s RouterOS software to defaults. Hold screwdriver pressed to thi s
rese t hole, and boo t the device. Hol d screwdriver i n place until RouterOS configurati on is cleare d (10 seconds).
Operating System Support
Currently teste d operating system is MikroTik RouterOS (starting from versi on 6).

See www.routerboard.com fo r more information . Conta ct [e-mail]
21/08/13
Safet y Notice
Electric shock hazard. This equipment is to be serviced by trained personnel only .
Warranty
Copyright and Trademarks . Copyright MikroTikls SIA . This manua l contains information protected by copyright law . No part
of it may be reproduce d or transmitte d i n any form without prior writte n permission from the copyrigh t holder. Route r-
BOARD, RouterOS, RouterBOOT a nd MikroTik are trademarks of MikroTikls SIA. All trademarks a nd registere d trademarks
appearin g in this manual ar e th e property of their respectiv e holders.
Hardware . MikroTik warrants all RouterBOARD series equipmen t fo r the term o f twelve (12 ) months from the shipping date to
be free o f defects in materials and workmanship unde r normal use and service, excep t in case o f damage caused by m e-
chanical, electrical or other accidental or intended damages caused by improper us e or du e to wind, rain, fir e or other acts of
nature.
To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization) procedure. Fo l-
low t he in structions b elow t o s ave t ime, e fforts, a voi d costs, a nd improve the spee d of the RM A process.
1. If y ou h ave p urchased y our p roduct f rom a M ikroTik R eseller , p lease c ontact t he R eseller c ompany r egarding all w a r-
ranty and repai r issues, the following instructions a pply O NLY if y ou p urchased y our e quipment directly from
MikroTik in Latvia.
2. We do not offer repairs for products that are not covered by warranty. Exceptions can be made for RB1000, RB1100
and RB1200 , ROUTERBOARD.
3. Out -- of -- warranty devices and devices not covered by warranty sent to MikroTik will be returned to the sender at
sender' s cost.
RM A Instructions a re lo cated o n o ur w ebpage h ere : http://rma.mikrotik.com
Manual . This manua l is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to, the
implied w arranty o f m erchantability a nd f itness f or a p articular p urpose . T he m anufacturer h as m ade e very e ffort t o en- sure
the accuracy of the content s of thi s manual, however, it i s possible that it may contain technical inaccuracies, typ o- graphica l
o r o ther errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect, inc i- dental,
consequential or other damages that may result from suc h a n inaccuracy, including, but not limite d to, loss of data o r
profits. Please report any inaccuracies f ound t o [e-mail]

See www.routerboard.com fo r more information . Conta ct [e-mail]
21/08/13