Rowlinson Modena Arbour User manual

Assembly Instructions
Modena Arbour English SS412
Before assembly
• We recommend that time is taken to read
the instructions before starting assembly,
then follow the easy step by step guide.
The instruction sheet is only a guide to
the assembly. Certain items may not be
shown to scale.
• Check all components prior to assembly
• This product should be assembled by no
less than two people
• Drill all components where indicated
x 2 Drill
Recommended tools for assembly
• Power drill/screwdriver
• 3mm drill bit
• Crosshead screwdriver bit
No. Fixing Kit Qty.
12 Wooden dowels 2
13 60mm screws 14
14 50mm screws 8
15 40mm screws 84
16 35mm screws 6
No. Components Qty.
1 Right-hand upright 1
2 Left-hand upright 1
3 Seat 1
4 Seat back 1
5 Back panel 1
6 Back right/front left rafter 2
7Front right/back left rafter 2
8 Centre roof slat 1
9 Roof slat sections 2
10 Small finial 4
11 Large finial 2
1
5
2
3
4
6
7
8
9
10
11

2. Seat back to uprights
Drill four holes in the frames of the seat back as shown in the diagram. Place the seat back on the seat between the
two uprights. Secure through the drilled holes into the legs of the uprights using 4 x 60mm screws. From the front of
the arbour, screw 1 x 60mm screw through each of the seat back frames into the seat frames.
Drill
Drill
60mm
360mm
Drill
60mm
60mm
Important Note:
Ensure rebate slots for
back panel are on the
inside at the back.
Drill
1. Seat to uprights
Drill four holes in each of the seat frames as shown in the diagram. Position the seat between the two uprights,
360mm from the bottom of the upright. Secure through the drilled holes into the upright legs using 8 x 60mm screws.

3. Back panel
Slot the back panel into the rebates of the uprights and slide down until it rests on the seat back. Ensure the top edge
of the panel is level with the top of the uprights. Secure the in place using 6 x 35mm screws.
4. Roof rafter assembly
Slot together one of each rafter using a dowel. Drill two holes in a large finial. Secure using 2 x 40mm screws centrally
over the join of the two rafters. Create a second rafter assembly in the same way.
35mm
Wooden
Dowel
40mm
Drill

Information
If in doubt of any aspect regarding the assembly, use or safety of your garden arbour please contact us:
Help Line: (Normal Office Hours) 01829 261 121
Email: [e-mail]
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
www.rowgar.co.uk
We constantly improve the quality of our products,
occasionally the components may differ from the
components shown and are only correct at time
of printing. We reserve the right to change the
specification of our products without prior notice.
2017 © Rowlinson Garden Products Ltd
6. Roof slats
Position the centre roof slat into the rebate and fix in place using 4 x 40mm screws. Evenly spread a roof slats section
over each side of the roof and secure using 2 x 40mm screws per slat, screw through the slats and into the rafters.
5. Rafters to uprights
Lift the rafter sections onto the rebates of the uprights. Drill two holes at each corner of the roof, then secure the
roof to the uprights using 2 x 50mm screw per corner. Drill two holes in each small finial. Secure the finials over the
joins between the rafter and the uprights using 2 x 40mm screws per finial.
Roof slat
Rafter Rafter
40mm
IMPORTANT: RETAIN FOR FUTURE REFERENCE READ CAREFULLY
• Periodically check all fastenings for tightness
• For domestic use only
40mm
50mm
Drill
40mm Drill