Royal Prestige JUICE EXTRACTOR User manual

USE & CARE MANUAL
IMPORTANT: To prevent personal injury and/or property damage,
read and follow the instructions and warnings in this Product Manual.
SAVE THESE INSTRUCTIONS •FOR QUESTIONS OR COMMENTS, SEE REVERSE FOR YOUR SERVICE CENTER CONTACT NUMBER.
FOR HOUSEHOLD USE ONLY.
PRODUCT MANUAL

2
Table of Contents
Introduction . . . . . . . . . . . . . . . . 2
Important Safeguards . . . . . . . . . . . . 3
Product Diagram . . . . . . . . . . . . . . 4
Before you Start. . . . . . . . . . . . . . . 6
Operation . . . . . . . . . . . . . . . . .8
Cleaning and Care Instructions . . . . . . . . 15
Troubleshooting/FAQ . . . . . . . . . . . 20
Technical Information . . . . . . . . . . . 23
Customer Service . . . . . . . . . . . . . 24
READ ALL INSTRUCTIONS BEFORE USE
Introduction
Welcome and congratulations on purchasing your Royal Prestige®Juice Extractor. Please be sure to read
this manual in its entirety before using your Royal Prestige®Juice Extractor to ensure that you have an enjoyable experience. The
valuable information contained in this manual will provide an overview of the product, some helpful hints to get you started, as well as
trouble-shooting tips should you have issues with this product in the future.
ROYAL PRESTIGE®
JUICE EXTRACTOR

3
Important Safeguards
This appliance is for household use only. Please carefully follow the instructions in the manual. (This appliance cannot be
covered under warranty if the product is abnormally or commercially used). Save the instruction manual for future reference.
These instructions are also available on www.royalprestige.com. If the appliance is given away as a gift, please include the
manual with the product.
When using electrical appliances, basic safety precautions should be followed including the following:
READ ALL INSTRUCTIONS.
Risk of
Electric Shock or Fire
• Do not immerse motor base in water or other liquid.
• The use of attachments not recommended or sold by the manufacturer may cause fire,
electric shock or injury.
• Do not spray water or flammable sprays near the appliance.
Risk of Injury • Close supervision is necessary when any appliance is used by or near children.
• Avoid contact with any moving parts.
• Always make sure the Hopper is closed securely in place before motor is turned on. Do not open
the Hopper while Juice Extractor is in operation.
• Turn switch to OFF position aer each use of your Juice Extractor. Make sure the motor stops
completely before disassembling.
• Do not put fingers or other objects into the Hopper during operation. If food becomes lodged, use
pusher or another piece of fruit or vegetable to push it down. When this method does not work,
turn the motor off and disassemble Juice Extractor to remove the remaining food.
• This device is not intended for use by persons (including children) whose physical, sensory or
mental abilities are different or reduced, or who lack experience or knowledge, unless such
persons receive supervision or training for the operation of the device by a person responsible for
your safety.
• Children should be supervised to ensure that they do not use the device as a toy.
Dangers
Related to Misuse
• Unplug from wall outlet when not in use before putting on or taking off parts, and before
cleaning.
• Do not operate any appliance with a damaged cord or plug, or aer the appliance malfunctions or
damaged in any manner. Return appliance to customer support for examination and/or repair.
• Do not use outdoors.
• Do not let cord hang over edge of table, counter, or another surface area.
• Do not use the appliance if the rotation wiper is damaged.
• Do not operate without the pulp cup in place.
• Do not alter or modify the appliance in any way.
• Do not use the appliance for anything other than its intended purpose as described
in the manual.
• The appliance should be used for a limited period of time to prevent overheating.
• Do not use the appliance on an uneven surface.
• Do not put the Juice Extractor parts in the dishwasher or extremely hot water.
• Do not use any hazardous chemicals to clean the appliance.
The following precautions are provided to ensure the safety of the user. Please carefully read through
the precautions and exercise care when using the appliance.
Warning: This label warns of the risk of death or severe injuries.
Caution: This label warns of the risk of injuries or appliance damage.
Prohibited. Do not disassemble.
Must take action.
ROYAL PRESTIGE®
JUICE EXTRACTOR

4
76
PARTS
Align the red dots ● on each part and
assemble in the order shown. Once
assembled, turn the drum lid clockwise
to close.
STEP 1
Top-set Assembly
STEP 2
Top-set and body assembly
Place the drum lid on the juicing bowl.
Align the down arrow ▼on the drum lid
with the OPEN mark on the body and
turn to the CLOSE position.
11. Cleaning Brush 12. Rotating Brush 13. Lid Opener
9. Juicing Screw7. Rotation Wiper 8. Strainer
* The products illustrated in this booklet may vary slightly from the actual product. * The products illustrated in this booklet may vary slightly from the actual product.
10. Pusher
+
+
+
+
+
+
Product Diagram
1. Hopper
Hopper Basket
8. Rotation Wiper 9. Ultrasqueezer
11. Cleaning Brush 12. Rotating Brush 13. Lid Opener
6. Body
5. Cap
3. Bowl
4. Pulp Cup 3. Feed 7. Juice Cup
11. Cepillo rotativo
76
PARTS
Align the red dots ● on each part and
assemble in the order shown. Once
assembled, turn the drum lid clockwise
to close.
STEP 1
Top-set Assembly
STEP 2
Top-set and body assembly
Place the drum lid on the juicing bowl.
Align the down arrow ▼on the drum lid
with the OPEN mark on the body and
turn to the CLOSE position.
11. Cleaning Brush 12. Rotating Brush 13. Lid Opener
9. Juicing Screw7. Rotation Wiper 8. Strainer
* The products illustrated in this booklet may vary slightly from the actual product. * The products illustrated in this booklet may vary slightly from the actual product.
10. Pusher
+
+
+
+
+
+
76
PARTS
Align the red dots ● on each part and
assemble in the order shown. Once
assembled, turn the drum lid clockwise
to close.
STEP 1
Top-set Assembly
STEP 2
Top-set and body assembly
Place the drum lid on the juicing bowl.
Align the down arrow ▼on the drum lid
with the OPEN mark on the body and
turn to the CLOSE position.
11. Cleaning Brush 12. Rotating Brush 13. Lid Opener
9. Juicing Screw7. Rotation Wiper 8. Strainer
* The products illustrated in this booklet may vary slightly from the actual product. * The products illustrated in this booklet may vary slightly from the actual product.
10. Pusher
+
+
+
+
+
+
Rotating Brush 12. Cleaning Brush
ROYAL PRESTIGE®
JUICE EXTRACTOR
12. Rotating Brush 13. Cleaning Brush
11. Pusher
10. Ultrasqueezer9. Strainer
2. Hopper locking mechanism

5
* The products illustrated/photographed in this manual may vary slightly from the actual product.
Align the red dots ●on each part and
assemble all the pieces in the order
shown. Once assembled, turn the
Hopper clockwise to close.
STEP 1
Top-set Assembly
STEP 2
Top-set and base assembly
Assemble the entire top-set onto the
base ensuring the arrow symbol ▼ on
the Hopper is aligned with the arrow
symbol on the base.
76
PARTS
Align the red dots ● on each part and
assemble in the order shown. Once
assembled, turn the drum lid clockwise
to close.
STEP 1
Top-set Assembly
STEP 2
Top-set and body assembly
Place the drum lid on the juicing bowl.
Align the down arrow ▼on the drum lid
with the OPEN mark on the body and
turn to the CLOSE position.
11. Cleaning Brush 12. Rotating Brush 13. Lid Opener
9. Juicing Screw7. Rotation Wiper 8. Strainer
* The products illustrated in this booklet may vary slightly from the actual product. * The products illustrated in this booklet may vary slightly from the actual product.
10. Pusher
+
+
+
+
+
+
ROYAL PRESTIGE®
JUICE EXTRACTOR

6
Before You Start
Check Before Operating Wash the parts before first use.
Note: The Ultrasqueezer needs to be locked in place
in order to close the Hopper.
STEP 1 Top-set Assembly
Assemble the strainer into the rotation wiper,
then place this assembly into the bowl ensuring
the red dot ●on the strainer is aligned with the
red dot ●on the bowl.
Place the Ultrasqueezer into the strainer. Turn
and press down on it until it clicks into place.
Place the Hopper onto the bowl aligning the red
dot ●on the Hopper with the red dot ●on the
bowl. Turn clockwise to close, aligning the red dot
●on the Hopper with the close mark .
1
2
3
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot ● on the drum lid with
the red dot ● on the juicing bowl. Turn
clockwise to close, aligning the red dot ●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot ● on
the strainer is aligned with the red dot ●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot ● on the drum lid with
the red dot ● on the juicing bowl. Turn
clockwise to close, aligning the red dot ●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot ● on
the strainer is aligned with the red dot ●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot
●
on the drum lid with
the red dot
●
on the juicing bowl. Turn
clockwise to close, aligning the red dot
●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot
●
on
the strainer is aligned with the red dot
●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
ROYAL PRESTIGE®
JUICE EXTRACTOR

7
Note: The Juice Extractor will not operate if
parts are not assembled properly.
STEP 2 Top-set and Base Assembly
Place the top-set on top of the base.
Align the arrow ▼ on the Hopper with
the arrow (open) on the base.
4
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot
●
on the drum lid with
the red dot
●
on the juicing bowl. Turn
clockwise to close, aligning the red dot
●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot
●
on
the strainer is aligned with the red dot
●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
Open/Close mark on the top-set.
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot ● on the drum lid with
the red dot ● on the juicing bowl. Turn
clockwise to close, aligning the red dot ●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot ● on
the strainer is aligned with the red dot ●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
For easy assembly hold the Hopper with
both hands and turn clockwise as shown
in the illustration.
TIP
5
Place the pulp cup under the pulp spout and
place the juice cup under the juice spout as
shown in the illustration. Pusher is optional.
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot ● on the drum lid with
the red dot ● on the juicing bowl. Turn
clockwise to close, aligning the red dot ●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot ● on
the strainer is aligned with the red dot ●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close
6
ROYAL PRESTIGE®
JUICE EXTRACTOR
98
HOW TO ASSEMBLE
The juicing screw needs to be locked in
place in order to close the drum lid.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Body Assembly
Place the juicing screw into the strainer.
Turn and press down on it until it clicks into
place.
Place the drum lid on to the juicing bowl
aligning the red dot ● on the drum lid with
the red dot ● on the juicing bowl. Turn
clockwise to close, aligning the red dot ●
on the drum lid with the close mark .
Check Before
Operating • Wash the parts before rst use.
• Ensure that the silicone ring is assembled properly.
2
3
46
Place the pulp cup under the pulp
spout and place the juice cup under the
juice spout as shown in the illustration.
Place the drum lid on the juicing bowl.
Align the down arrow ▼ on the drum
lid with the OPEN mark on the body
and turn to the CLOSE position.
Open/Close mark on the top-set.
5
For easy assembly hold the drum lid
by grabbing the feeding tube and turn
clockwise as shown in the illustration.
TIP
Assemble the strainer into the rotation
wiper then place this assembly in to the
juicing bowl ensuring the red dot ● on
the strainer is aligned with the red dot ●
on the juicing bowl.
1
Note | The juicer will not operate if the down arrow
▼
on the drum lid is not completely aligned
with the CLOSE mark on the body.
Open
Close

8
Operation
STEP 1
After preparing the ingredients, plug the power cord into a wall outlet.
Note: • Do not touch the power cord with wet hands. It may cause electrical shock, short-circuit, or re.
• Check the safety of the wall outlet.
STEP 2
Press the FORWARD button to operate.
Note: • Forward: Pulls down and slowly presses the ingredients.
• Reverse: Pushes the ingredients back up to dislodge them.
If the ingredients become jammed in the Ultrasqueezer and the Hopper does not open, press the OFF button. Then
press and hold the REVERSE button until the ingredients become dislodged. Repeat REVERSE - OFF - FORWARD as often
as needed to achieve the desired result.
REVERSE: Pushes the ingredients back up to dislodge them.
The REVERSE button only works while holding down the switch.
Switch OFF ensuring that the Juice Extractor comes to a complete stop. Then press REVERSE. Hold
the REVERSE button for 2-3 seconds and release. Repeat as needed. Let the Juice Extractor stop
completely before using the REVERSE button to prevent malfunction.
If the Juice Extractor does not work after these steps, disassemble and clean the parts before
operating the Juice Extractor again.
If the Juice Extractor stops during operation
Switch the button to OFF position then press and
hold the REVERSE button until the ingredients
become dislodged. Repeat REVERSE - OFF - FORWARD
as needed.
FORWARD : Pulls down the food
OFF : Stops the operation
REVERSE : Pushes the food back up
OFF OFF
▲ ▲ ▲
REVERSE FORWARD
GGGG
Note |
➊ ➋ ➌ ➍
ROYAL PRESTIGE®
JUICE EXTRACTOR

9
Insert the prepared ingredients one piece at a time.
• Prepare ingredients for optimal extraction.
• If a large quantity of ingredients is put into the Hopper, it can cause the Juice Extractor to stop.
• Insert the ingredients one piece at a time.
• Remove hard seeds or pits in fruits. When juicing frozen fruits, completely thaw before juicing.
Note:
Tip:
Tip:
STEP 3
Use the cap to make mixed juices, stop juice
from dripping, or rinse between dierent juices.
After juice and pulp are completely extracted, switch the unit OFF.
• If the remaining ingredients in the bowl have not been extracted completely, the Hopper may not
open easily. Aer each extraction, run the Juice Extractor for an additional 30 seconds to let
it extract the remaining pulp.
• When the Hopper is stuck, press the REVERSE - OFF - FORWARD button in this order; switching back
and forth 2 or 3 times to dislodge the ingredients. Then place hands on top of the Hopper’s lid and
firmly press down, while simultaneously turning it counter clockwise to open.
» Depending on the ingredients, pour water down the Hopper to rinse out the interior
of the bowl and then attempt to remove it.
• Juicing with the cap closed makes various mixed juice creations when different fruits and vegetables,
milk, banana, beans etc. are selected.
• Aer juicing, close the cap to stop the juice from dripping, especially when disassembling the bowl
off the base.
• When making different juices quickly rinse away any leover flavors by running a glass of water in
the Juice Extractor with the cap closed.
• Leave the cap open when juicing ingredients that create excessive foam during
extraction (e.g. apples, celery).
• Pay close attention when operating with the cap closed. Juice may overflow if the juice collected
in the bowl exceeds its capacity marked on the bowl.
Note:
Note :
Tip:
Cap
STEP 4
STEP 5
• Tough and fibrous ingredients: Cut to size.
• Fibrous leafy vegetables (celery, kale, collard greens, etc.): Cut the stems to size.
Hard vegetables & high fiber foods | (E.g. carrots, beets, & spinach)
• So ingredients: Cut ingredients to size. Insert the prepared ingredients into the feed
basket and push down the ingredient with the basket lid to extract.
So Fruits & Vegetables | (E.g. apples, oranges & tomatoes)
1110
HOW TO OPERATE
After preparing the ingredients, plug the power cord into a wall outlet.
Press the FORWARD button to operate.
Insert the prepared ingredients into the feeding tube, one piece at a time.
If the juicer stops during operation:
Switch the button to OFF position then press and
hold the REVERSE button until the ingredients
become dislodged.
Repeat REVERSE - OFF - FORWARD as needed.
FORWARD : Pulls down the food
OFF : Stops the operation
REVERSE : Pushes the food back up
▶▶▶
4
1 3
2
OFF OFFREVERSE FORWARD
Note |
Note |
Note
Tip |
Tip |
Note |
If the ingredients become jammed in the screw and the drum lid does not open, press the OFF
button. Then press and hold the REVERSE button until the ingredients become dislodged.
Repeat REVERSE - OFF - FORWARD as often as needed to achieve the desired result.
Use the smart cap to make mixed juice, block juice from dripping,
or rinse between dierent juices.
After juice and pulp have been completely extracted, switch the unit OFF.
TIP
Note
Note
Hard vegetables & high ber foods
Soft Fruits & Vegetables
| (E.g. carrots, beets, & spinach)
| (E.g. apples, oranges & tomatoes)
Insert into
the feeding
tube
Insert into
the feeding
basket
Smart Cap
· Do not touch the power cord with wet hands. It may cause electrical shock,
short-circuit, or re.
· Ensure the power cord is plugged into a power outlet.
· Forward: Pulls down and slowly masticates the ingredients.
· Reverse: Pushes the ingredients back up to dislodge them.
· REVERSE: Pushes the ingredients back up to dislodge them.
The REVERSE button only works while holding down the switch.
· Switch OFF ensuring that the juicer comes to a complete stop. Then press REVERSE.
Hold the REVERSE button for 2-3 seconds and release. Repeat as needed. Let the
juicer stop completely before using the REVERSE button to prevent malfunction.
· If the juicer does not work after these steps, disassemble and clean the parts before
operating the juicer again.
· Prepare ingredients for optimal extraction.
· If large quantity of ingredients are put into the feeding tube, it can cause the juicer to stop.
Insert the ingredients one piece at a time.
· Remove hard seeds or pits in fruits. When juicing frozen fruits, completely thaw before juicing.
·
Tough and brous ingredients:
Cut to 1/2-1 inches wide and 2 inches long.
· Fibrous leafy vegetables (celery, kale, collard greens, etc.):
Cut the stems into 2 inches long and bundle up the leafy part as you
insert them into the juicer.
· Soft ingredients: Cut ingredients into 1-4 pieces. Insert the prepared
ingredients into the feeding basket and push down the ingredient
with the basket lid to extract.
· Juicing with the smart cap closed creates various mixed juice creations with dierent fruits
and vegetables, milk, banana, beans and other ingredients.
· After juicing, close the smart cap to stop juice from dripping, especially when disassembling
the juicing bowl o of the base.
· When making dierent juices, quickly rinse any left over avors by running a glass of water
in the juicer with the smart cap closed.
· Leave the smart cap open when juicing ingredients that often creates foam during extraction.
(e.g. apples, celery)
· Pay close attention when operating with the smart cap closed. Juice may overow if the juice
collected in the juicing bowl exceeds its capacity.
· If the remaining ingredients in the juicing bowl have not been extracted completely, the drum
lid may not open easily. (After each extraction, run the juicer for additional 30 seconds to let
the juicer extract the remaining pulp.)
When the drum lid is stuck, press the REVERSE - OFF - FORWARD button in the order, switching
back and forth 2~3 times to dislodge. Then place your hands on top of the drum lid and rmly
press down as you simultaneously turn the drum lid counter clockwise to open.
※Depending on the ingredients, pour water down the feeding tube to rinse out the interior
of the juicing bowl and then try to take o the drum lid.
Insert
into the
Hopper
Insert
into the
feed
basket
cap
ROYAL PRESTIGE®
JUICE EXTRACTOR

10
Helpful Hints
1. Operating the Juice Extractor without ingredients can cause damage to the Ultrasqueezer.
2. Do not continuously operate the Juice Extractor for more than 30 minutes.
This can overheat the motor and damage it. Aer continuous use, let the Juice Extractor rest for 30 minutes
to cool down before starting another session.
3. Do not put fingers or other objects into the Hopper. Always use provided pusher when needed.
If other objects are inserted into the Hopper during operation, they can get stuck and damage the Juice Extractor
parts and/or cause injury.
4. Do not put dried or hard ingredients like whole grains, fruits with hard seeds or ice into the Juice Extractor.
These may damage the parts (e.g. bowl, Ultrasqueezer, and strainer).
• Beans or grains can be used if soaked overnight or boiled.
• Fruits with pits and hard seeds must be pitted before juicing (e.g. nectarines, peaches, mangoes and cherries).
• When using frozen fruits with small seeds such as grapes, completely thaw before inserting them
into the Juice Extractor.
5. Do not use ingredients containing excessive amounts of vegetable oil or animal fat. Do not use the Juice Extractor
to extract vegetable oil from ingredients.
If vegetable/animal oil gets on the Ultrasqueezer, it may reduce performance and even damage the part.
6. Do not reinsert the extracted pulp into the Juice Extractor. This can cause the unit to stop or cause the Hopper
not to open.
7. Aer juicing ingredients with seeds like grapes, thoroughly clean all the crevices on the bottom of the Ultrasqueezer.
Juice Extractor damaged due to owner negligence or from not following the instructions in this manual will void the warranty.
Hard seeds Peach, nectarines, apricot, plum, mango, etc.
Remove hard seeds or pits from the ingredients before juicing
Hard or inedible skins Pineapple, melon, mango, orange, etc.
Peel the skin from the ingredients before juicing.
Frozen fruits or ice Frozen strawberry, blueberry, raspberry, etc.
Completely thaw frozen fruits before juicing. Do not use ice.
DO NOT put the following ingredients into the Juice Extractor:
ROYAL PRESTIGE®
JUICE EXTRACTOR

11
Vegetable/animal oil Sesame seed, butter, margarine, etc.
Do not extract ingredients containing vegetable or animal oil. This can reduce
performance and even damage the Juice Extractor.
Others Coconut, sugarcane, whole grains, etc.
Do not extract ingredients with no water content.
Experience the best quality juice by understanding each ingredient’s characteristics
and knowing the optimal way of handling them.
The Juice Extractor is an innovative product that uses a patented slow-speed juicing technology to eciently extract
the juice from ingredients. The Juice Extractor is designed to obtain the best result from ingredients with rm
composition and with high water content. For best result, each ingredient should be prepared and extracted depending
on its characteristics and properties.
Tips On Ingredients
Before Operating
• Before Operating: If the Juice Extractor is jammed or if the Hopper does not
open, press the REVERSE button and hold until the ingredient becomes dislodged.
Repeat REVERSE-OFF-FORWARD as needed.
• Continue operating the Juice Extractor until all the ingredients in the bowl
are extracted. The Hopper may not open easily if there is a lot of pulp remaining
in the Juice Extractor.
• Every ingredient yields different amounts of juice.
Juice Yield
• For the optimal extraction and maximum juice yield, cut the ingredients following the
guidelines given in this section.
• Insert ingredients slowly, monitoring how they are extracted. The juice yield may
vary depending on the juicing speed.
Adjusting
the Amount
of Pulp in the Juice
• Depending on the ingredient, you may get extra pulp when juicing continuously.
• To reduce the amount of pulp, disassemble the top-set and wash frequently.
ROYAL PRESTIGE®
JUICE EXTRACTOR

12
SOFT FRUITS AND VEGETABLES (e.g. oranges, tomatoes):
PREPARATION TIPS:
• Cut ingredients cut to size.
EXTRACTION TIPS:
• Slowly insert the ingredients, one piece at a time.
• Use the pusher to push the ingredients down the Hopper. (The pusher also helps prevent juice from spraying
out of the Hopper when extracting ingredients with high water content.)
• Leave the cap open when juicing ingredients that create excessive foam during extraction, like apples
and celery. (Foam can accumulate if operated with the cap closed.)
• It is recommended that the extracted juice be consumed within 48 hours aer extracting. Depending on the
density of the ingredients, the extracted juice can gradually separate into layers over time.
• If there is an excessive amount of foam, use a mesh strainer to separate it from the juice.
HARD FRUITS AND VEGETABLES (e.g. carrots, potatoes, beets):
PREPARATION TIPS:
• Slice the ingredients cut to size.
• Peel the skin off oranges, and for tomatoes and apples, take out the stem.
• If the ingredients are larger than the Hopper, cut the ingredients into pieces that will fit into it.
• Fruits with seeds must be pitted before extraction. Cut to size then slowly insert them down the
Hopper.
• Hard fruits and vegetables may put excess strain onto the motor and cause it to stall.
• To increase the juice yield, juice fruits and vegetables with high water content.
ROYAL PRESTIGE®
JUICE EXTRACTOR

13
EXTRACTION TIPS:
• Slowly insert the ingredients, one at a time.
• Pace the juicing speed, ensuring each ingredient is thoroughly extracted.
• To maximize the juice yield, juice ingredients with high water content.
INGREDIENTS WITH SMALL SEEDS(e.g. raspberry, pomegranate, grape):
Slowly insert ingredients with small seeds to prevent clogging the Strainer.
PREPARATION TIPS:
• When juicing frozen ingredients, make sure they are completely thawed (e.g. raspberry, strawberry).
• Rinse ingredients thoroughly. Remove all stems.
• For pomegranate, discard the skin and juice only the inner part.
EXTRACTION TIPS:
• Depending on the size of the grape, insert 3-5 grapes at a time while monitoring the extraction result.
• For ingredients like pomegranate and raspberry, insert about 1 tablespoon (5g) at a time.
• Frozen ingredients usually lose a significant amount of fluid from thawing. When juicing, mix milk or yogurt
to balance the fluid lost.
• Insert ingredients slowly to minimize the amount of leftover seeds in the Strainer.
• For best results, use ingredients with a higher amount of fluid (e.g. apple, pear).
CAUTION:
If the Hopper does not open due to excessive amount of small seeds left in the bowl, continuously
run the Juice Extractor for 30 seconds to extract any leftover seeds. If the Hopper is still stuck,
repeat REVERSE - OFF- FORWARD until the ingredients become dislodged. Then twist the Hopper
to open while pushing downwards with palms. (Depending on the ingredient, pour some water
down the Hopper for a quick rinse to help dislodge.)
ROYAL PRESTIGE®
JUICE EXTRACTOR

14
CAUTION:
• The fibers from tough ingredients like celery can wrap around the Ultrasqueezer and affect the
Juice Extractor’s performance. Cut the stems to size.
• Foam can build up from juicing fibrous ingredients. Use strainer to remove the foam before
serving.
• For ingredients like pineapple, slice off the rind of the pineapple and cut around the fibrous core.
Cut the flesh of the pineapple to smaller pieces.
• Recommended amount of juicing per session is 500g (approximately 2¼ cups). When juicing more
than this amount, wash the top-set before continuing to juice.
FIBROUS AND/OR TOUGH LEAFY INGREDIENTS (e.g. celery, kale, pineapple):
Fibrous ingredients like celery and kale should be cut to size.
PREPARATION TIPS:
• Separate each stem. Cut outer stems to size.
EXTRACTION TIPS:
• Slowly insert the prepared ingredients one at a time.
• Insert more ingredients aer the previous ones have been completely extracted.
■ Roll leaves in spiral before inserting into the Juice Extractor.
■ Insert the leafy part of the ingredients first, then alternate between leafy parts and stems.
■ For ingredients like cilantro or wheatgrass, grab a handful and insert in a bundle.
• When juicing leafy ingredients like celery and kale, do not collect more than 500g (approximately
2¼ cups) per session. For best results, disassemble and wash the top-set before juicing again.
• If leafy ingredients wrap around the Ultrasqueezer, open the Hopper and remove the fibers before
continuing to juice.
• It’s best to use ingredients with a higher amount of fluid, like apples or carrots.
ROYAL PRESTIGE®
JUICE EXTRACTOR

15
NOTE:
Extract all the remaining pulp in the bowl before stopping the Juice Extractor.
For easier clean up, operate the Juice Extractor for an additional 30 seconds after the juice
is extracted.
When the Hopper is stuck, press the REVERSE – OFF – FORWARD button in this order, switching back
and forth 2 to 3 times to dislodge. Then place hands on the lower part of the Hopper and firmly press
down simultaneously turning the Hopper counter clockwise to open.
NOTE:
When moving the appliance, do not lift
by grabbing the Hopper. Always lift the
appliance by grabbing the base or handle.
Switch OFF and unplug the power cord from
the wall outlet.
1
Turn the Hopper counter clockwise to open.
2
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
Lift top set vertically o base.
3
Remove the Ultrasqueezer, strainer and rotation wi
per unit from the bowl. Clean with provided brush.
4
Cleaning and Care
ROYAL PRESTIGE®
JUICE EXTRACTOR

16
NOTE:
Immediately clean the Juice Extractor
after each use. If remaining residue in
the Juice Extractor dries up, it can make
disassembling and clean-up difficult. The
excess buildup can cause poor performance
in future uses.
For easier disassembly, place the Top-set in
the sink and run water through it.
Thoroughly dry the bottom of the
Ultrasqueezer where it connects to the metal
cylinder shaft on the Base.
TIP:
Thoroughly clean the Ultrasqueezer, ensuring that it is clean without any residue.
Completely dry before using.
NOTE:
After juicing ingredients with seeds, make sure to thoroughly clean the bottom crevice of
the Ultrasqueezer. If this area isn’t properly cleaned, it can affect the balance between the
Ultrasqueezer and the Strainer and damage the parts.
Under running water, clean the outside of the
Ultrasqueezer with a dish scrub. Use the tip of
a cleaning tool to push out any residue in the
crevices on the bottom of the part.
5
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
ROYAL PRESTIGE®
JUICE EXTRACTOR

17
TIP: If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the Juice Extractor.
NOTE: Soak the bowl in a solution of warm
water with baking soda or a little bit of
bleach to clean the excess buildup.
TIP:
It is not necessary to completely clean the Juice Extractor when making multiple juices during
a single juicing session.
When finished juicing, always disassemble and clean thoroughly to prevent residue buildup.
Clean the base with a soft damp towel and dry.
6
With the cap closed, ll the juicing bowl with water
and turn on the Juice Extractor.
Let it run for a moment. Open the cap and let
the water run out of the bowl.
12
Quick Rinsing
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
1918
HOW TO DISASSEMBLE AND CLEAN
Tip |
Clean the body with a soft damp towel
and dry.
Note |
Tip |
Note |
Under running water, clean the outside
of the juicing screw with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the juicing screw.
With the smart cap closed, ll the juicing
bowl with water and turn on the juicer.
Let it run for a moment. Open the
smart cap and let the water run out of
the juicing bowl.
Turn the drum lid counter clockwise to
open.
Note |
Note |
Switch OFF and unplug the power cord
from the wall outlet.
1
1 6
7
2
Turn the top-set counter clockwise and
lift o the body.
3
1
2
Quick Rinsing
Note |
TIP |
Remove the juicing screw, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Place the juicing bowl under running
water.
4
5
* The products illustrated in this booklet may vary slightly from the actual product.
Extract all the remaining pulp in the
juicing bowl before stopping the juicer.
For easier clean up, operate the juicer for
an additional 30 seconds after the juice is
extracted.
When the drum lid is stuck, press the
REVERSE – OFF – FORWARD button in this
order, switching back and forth 2 to 3 times
to dislodge. Then place both hands on
the drum lid and firmly press down while
simultaneously turning the drum lid to open.
* Fill the juicing bowl with water and run
the juicer before opening the drum lid. It
may help to open the drum lid when stuck.
·
·
·
When moving the appliance, do not lift
by grabbing the feeding tube. Always lift
the appliance by grabbing the body or
handle.
Immediately clean the juicer after each
use. If remaining residue in the juicer dries
up, it can make disassembling and clean-
up dicult. The excess build up can cause
poor performance in future uses.
For easier disassembly, place the top-
set in the sink and run the water through
from the top of the top-set.
Thoroughly dry the bottom of the juicing
screw.
The round brush can clean the juice
spout of the juicing bowl.
After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the juicing screw. (If this area
isn’t properly cleaned, it can cause the
part to be damaged.)
Thoroughly clean the juicing screw
ensuring that the juicing screw is clean
without any residue.
Completely dry before using.
If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the juicer.
It is not necessary to completely clean
the juicer in between making multiple
juices during a single juicing session.
When nished with juicing, always
disassemble and clean thoroughly
between juicing sessions to prevent
residue buildup.
ROYAL PRESTIGE®
JUICE EXTRACTOR

18
How to Clean Silicone Parts
SILICONE BRUSHES
Pull out the Silicone brushes from the rotation wiper
to clean.After cleaning, insert into the slot with the tail
pointing down as shown in the illustration.
SILICONE RING
Remove the silicone ring from the strainer to clean.
After cleaning, push in the silicone ring with the
smaller surface facing down.
Clean the Rotation Wiper under running water. Thoroughly dry after cleaning.
Tip:
2120
HOW TO USE THE CLEANING TOOL
Hold the cleaning tool with one hand and insert
the strainer into the cleaning tool.
HOW TO CLEAN SILICONE PARTS
Silicone Brush
Pull out the silicone brush from
the rotation wiper to clean.
After cleaning, insert into the slot
with the tail pointing down as
shown in the illustration.
Silicone Ring
Remove the silicone ring from
strainer to clean.
After cleaning, push in the silicone
ring.
Smart Cap
Remove from the juice spout
to clean.
After cleaning, attach the smart
cap to the smart cap silicone on
the juice spout.
Clean the rotation wiper under running water.
Thoroughly dry after cleaning. Before assembling the top-set, ensure that the silicone ring is
rmly inserted.
If the silicone ring is not rmly inserted, juice may leak from the bottom of the juicing bowl.
Tip |
Note |
The cleaning tool makes clean-up quick and easy.
Completely dry after cleaning.
Tip |
1
After cleaning, remove the strainer from the
cleaning tool. Dry before storing.
4
Under running water, rotate the cleaning tool
and the strainer in opposite directions to clean.
2
Thoroughly rinse the inside and outside of
the strainer under running water.
3
Note | Insert the strainer until you hear a click.
* The products illustrated in this booklet may vary slightly from the actual product.
Cleaning inside of the bowl
Please unscrew the cover on the bottom and clean inside.
After cleaning, make sure that protrusion part of gear is
placed on the outer part so it ts (connects) with the drum.
Sequence of assembly is in reverse order of disassembly.
CAP
Remove from the juice spout to clean.
After cleaning, insert the silicone piece into the cap
and attach the cap into the juice spout.
ROYAL PRESTIGE®
JUICE EXTRACTOR

19
How to Use the Rotating Brush
The rotating brush makes clean-up quick and easy. Completely dry after cleaning.
Tip:
Note:
Use the included Cleaning Brush to remove hard-to-reach bits after using the rotating brush.
Thoroughly rinse the inside and outside of
the strainer under running water.
Hold the rotating brush with one hand and insert the
strainer into the brush.
NOTE: Insert the Strainer until you hear a click.
1
Under running water, rotate the rotating brush
and the strainer in opposite directions to clean.
2
3
After cleaning, remove the strainer from the rotating
brush. Dry before storing.
4
2120
HOW TO USE THE CLEANING TOOL
Hold the cleaning tool with one hand and insert
the strainer into the cleaning tool.
HOW TO CLEAN SILICONE PARTS
Silicone Brush
Pull out the silicone brush from
the rotation wiper to clean.
After cleaning, insert into the slot
with the tail pointing down as
shown in the illustration.
Silicone Ring
Remove the silicone ring from
strainer to clean.
After cleaning, push in the silicone
ring.
Smart Cap
Remove from the juice spout
to clean.
After cleaning, attach the smart
cap to the smart cap silicone on
the juice spout.
Clean the rotation wiper under running water.
Thoroughly dry after cleaning. Before assembling the top-set, ensure that the silicone ring is
rmly inserted.
If the silicone ring is not rmly inserted, juice may leak from the bottom of the juicing bowl.
Tip |
Note |
The cleaning tool makes clean-up quick and easy.
Completely dry after cleaning.
Tip |
1
After cleaning, remove the strainer from the
cleaning tool. Dry before storing.
4
Under running water, rotate the cleaning tool
and the strainer in opposite directions to clean.
2
Thoroughly rinse the inside and outside of
the strainer under running water.
3
Note | Insert the strainer until you hear a click.
* The products illustrated in this booklet may vary slightly from the actual product.
Cleaning inside of the bowl
Please unscrew the cover on the bottom and clean inside.
After cleaning, make sure that protrusion part of gear is
placed on the outer part so it ts (connects) with the drum.
Sequence of assembly is in reverse order of disassembly.
ROYAL PRESTIGE®
JUICE EXTRACTOR

20
Troubleshooting QA
CONDITION REASON SOLUTION
There is no power
to the Juice Extractor
Juice Extractor will not operate if
parts are not assembled properly.
• Check if the power cord is properly plugged in.
• Check if the Hopper and the bowl are properly
assembled.
• Check to see if the Top-set and the Base are properly
assembled.
Low juice yield Each ingredient has different
amounts of liquid that will yield
different amounts of juice.
If the ingredients are not fresh,
they may contain reduced
amounts of fluid, which will
yield less juice.
• If the ingredient itself has low water content, it may
help to soak it in water before juicing.
• If juicing ingredients with small seeds, aer a few
servings, it may reduce the juice yield. For best
results, disassemble and wash the Top-set in
between juicing.
• If there is seed residue on the bottom of the
Strainer, this can affect Juice Extractor performance
and the overall juice yield.
There is too much pulp
in the juice
When continuously juicing, and
depending on the ingredient, the
juice may contain a lot
of fine pulp.
• To reduce the fine pulp, clean the
Top-set frequently and extract the pulp.
• Use a mesh strainer and put the juice through it to
collect the unwanted pulp.
• If the Strainer and the Ultrasqueezer are damaged
and affecting the Juice Extractor’s performance, it is
recommended the parts be replaced.
• The lifetime of each part may vary depending on
length and method of use and ingredients extracted.
To order parts, see customer service information
on page 24.
• If too many ingredients are inserted at the same
time, it may cause the Juice Extractor to stop
frequently. This can lead to pulpy juice. Insert the
ingredients slowly.
ROYAL PRESTIGE®
JUICE EXTRACTOR