Royal Prestige Maxtractor Guide

CARE AND USE MANUAL
B77.JM3.HYCITE.1-131107M

Important Safeguards
Safety Warning
Parts
How to Assemble
How to Operate
Tips on Operation
Tips on Ingredient
Ingredients Preparation
How to Disassemble and Clean
How to Clean Silicone Parts
How to Use the Cleaning Tool
Troubleshooting Q&A
Specications
04
05
06
08
10
12
13
14
18
20
21
22
24
CONTENTS
Read all Instructions Before Use

5
4
• This appliance is for household use only. Please follow the instructions in the manual carefully.
(The appliance cannot be covered under the manufacturer’s warranty if the product is used in a
way not intended by the manufacturer or commercially.)
• Save the instruction manual for future reference.
• If the appliance is given as a gift, please include the manual with the product.
The following precautions are provided to ensure the safety of the user. Please carefully read
through the precautions and exercise care when using the appliance.
Warning: This label warns of the risk of death or severe injuries.
Caution: This label warns of the risk of injuries or appliance damage.
Prohibited Do not disassemble Must take action
IMPORTANT SAFEGUARDS SAFETY WARNING
Do not use any
hazardous chemicals
to clean the appliance;
* It may change the
color of the appliance
or result in a re.
Do not repair, disassemble
the base, or customize
the appliance;
* The appliance may
not operate properly
causing re, electric
shock, or injury.
Do not use the appliance on
an uneven surface;
* It may cause a
malfunction if the
appliance tips over.
Do not keep or
operate the appliance
near infants or
toddlers;
*It may injure them.
Do not spray water or
ammable sprays near
the appliance;
* It may cause
an explosion or
electrical shock.
Unplug the power
cord when not in use.
Do not put the
maXtractor
™
parts in the
dishwasher
or extremely hot water;
*The parts may wear
faster.
Do not put ngers or
other objects into the
hopper while it is in
operation;
*It may cause injury.
When using electrical appliances, basic safety precautions should always be followed
1. Read all instructions.
2. To protect against risk of electrical shock do not immerse motor base in water or other liquid.
3. Close supervision is necessary when any appliance is used by or near children.
4. Unplug from outlet when not in use before putting on or taking o parts, and before cleaning.
5. Avoid contacting moving parts.
6. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions
or damaged in any manner. Return appliance to the customer support for examination and/or
repair.
7. The use of attachments not recommended or sold by the manufacturer may cause re, electric
shock or injury.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter.
10. Always make sure the hopper is closed securely in place before motor is turned on. Do not open
the hopper while maXtractor
™
is in operation.
11. Be sure to turn switch to OFF position after each use of your maXtractor
™
. Make sure the motor
stops completely before disassembling.
12. Do not put ngers or other objects into the hopper during operation. If food becomes lodged, use
pusher or another piece of fruit or vegetable to push it down. When this method does not work,
turn the motor o and disassemble maXtractor
™
to remove the remaining food.
13. Do not use the appliance if the rotation wiper is damaged.
14. Do not operate without the pulp container in place.
15. Do not alter or modify the appliance in anyway.
16. Do not use the appliance for anything other than its intended purpose as described in the manual.
17. The appliance should be used for limited period of time.

7
6
PARTS
* The products illustrated/photographed in this booklet may vary slightly from the actual product.
2. Juicing Bowl
3. Pulp
Container
6. Juice
Container
4. Smart Cap
5. Base
1. Hopper
9. UltraSqueezer™8. Strainer
10. Pusher
7. Rotation Wiper
11. Cleaning Brush
+
+
+
+
Align the red dots ●on each part and
assemble in the order shown. Once
assembled, turn the hopper clockwise to
close.
STEP 1
Top-set Assembly
STEP 2
Top-set and base assembly
+
+
Assemble the entire top-set onto the
base ensuring the arrow symbol ▼on the
hopper is aligned with the arrow symbol
on the base. Turn the top-set clockwise
ensuring the arrow symbol ▼ is aligned
with the arrow symbol .
Pusher
Align
Align the dots ● and slide
the pusher in.
Detachable
+
+

9
8
HOW TO ASSEMBLE
Firmly insert the compression silicone
into the slot below the pulp spout.
The MaXtractor™ may leak if not assembled
properly.
Note | The UltraSqueezer™ needs to be locked in
place in order to close the hopper.
Note |
MaXtractor™ will not operate if parts are
not assembled properly.
Note |
STEP 1
Top-set Assembly
STEP 2
Top-set and Base Assembly
Assemble the strainer into the rotation
wiper, then place this assembly into the
juicing bowl ensuring the red dot
●
on
the strainer is aligned with the red dot
●
on the juicing bowl.
Place the UltraSqueezer™ into the strainer.
Turn and press down on it until it clicks
into place.
Place the hopper onto the juicing bowl
aligning the red dot
●
on the hopper
with the red dot
●
on the juicing bowl.
Turn clockwise to close, aligning the red
dot
●
on the hopper with the close mark
.
Check Before
Operating
• Wash the parts before rst use.
• Ensure that the compression silicone and silicone ring are assembled properly.
1
2
3
4
57
Place the pulp container under the
pulp spout and place the juice
container under the juice spout as
shown in the illustration.
Place the top-set on top of the base.
Align the arrow ▼on the hopper with
the arrow (open) on the base then
slightly turn the top-set clockwise,
until the hopper arrow is aligned with
the arrow (close) .
Open
Close
Detachable
Open/Close mark on the top-set.
6
For easy assembly hold the hopper
and turn clockwise as shown in the
illustration.
TIP

11
10
Use the smart cap to make mixed juices,
stop juice from dripping, or rinse between
dierent juices.
After juice and pulp are completely extracted, switch the unit OFF.
HOW TO OPERATE
After preparing the ingredients, plug the power cord into a wall outlet.
Press the FORWARD button to operate.
Insert the prepared ingredients one piece at a time.
• Do not touch the power cord with wet hands. It may cause electrical shock,
short-circuit, or re.
• Check the safety of the wall outlet.
• Forward: Pulls down and slowly masticates the ingredients.
• Reverse: Pushes the ingredients back up to dislodge them.
• Fibrous leafy vegetables (celery, kale, etc.):
» Separate each stem. Cut the outer stems that are thick and tough to 4 inches long or
less.
» Bundle up the leafy vegetables as inserting into the maXtractor™. Alternate between
leafy parts and stems.
• Before extracting, remove hard seeds or pits in ingredients.
• When juicing frozen fruits with small seeds, ensure that even the seeds are completely
thawed.
• Insert the ingredients one piece at a time.
• Align the dots ●and slide the pusher in.
• After inserting ingredients, use the pusher when it is necessary. Too much use of the
pusher may aect the juice quality.
» Intermittently use the pusher for soft ingredients like tomatoes and apples. Constant
use of pusher for soft ingredients may aect the juice quality.
• If the remaining ingredients in the juicing bowl have not been extracted completely,
the hopper may not open easily. After each extraction, run the maXtractor™ for an
additional 30 seconds to let the maXtractor™ extract the remaining pulp.
• When the hopper is stuck, press the REVERSE - OFF - FORWARD button in this order;
switching back and forth 2 or 3 times to dislodge the ingredients. Then place hands
on top of the hopper and rmly press down while simultaneously turning it counter
clockwise to open.
» Depending on the ingredients, pour water down the hopper to rinse out the interior
of the juicing bowl and then attempt to remove it.
• Juicing with the smart cap closed creates various mixed juice creations when
dierent fruits and vegetables, milk, banana, beans etc. are selected.
• After juicing, close the smart cap to stop the juice from dripping, especially when
disassembling the juicing bowl o the base.
• When making dierent juices quickly rinse away any leftover avors by running a
glass of water in the maXtractor™ with the smart cap closed.
• Leave the smart cap open when juicing ingredients that create excessive foam
during extraction, (e.g. apples, celery).
• Pay close attention when operating with the smart cap closed. Juice may overow
if the juice collected in the juicing bowl exceeds its capacity marked on the bowl.
• REVERSE: Pushes the ingredients back up to dislodge them.
The REVERSE button only works while holding down the switch.
• Switch OFF ensuring that the maXtractor™ comes to a complete stop. Then press
REVERSE. Hold the REVERSE button for 2-3 seconds and release. Repeat as needed.
Let the maXtractor™ stop completely before using the REVERSE button to prevent
malfunction.
• If the maXtractor™ does not work after these steps, disassemble and clean the
parts before operating the maXtractor™ again.
If the maXtractor™ stops during operation:
Switch the button to OFF position then press and
hold the REVERSE button until the ingredients
become dislodged.
Repeat REVERSE - OFF - FORWARD as needed.
FORWARD : Pulls down the food
OFF : Stops the operation
REVERSE : Pushes the food back up
▶▶▶
4
1 3
2
OFF OFFREVERSE FORWARD
Note |
Note |
Note |
Tip |
Note |
Note |
Tip |
Note |
If the ingredients become jammed in the UltraSqueezer™ and the hopper does not open,
press the OFF button. Then press and hold the REVERSE button until the ingredients become
dislodged. Repeat REVERSE - OFF - FORWARD as often as needed to achieve the desired result.
Smart cap
STEP 1 STEP 3
STEP 4
STEP 5
STEP 2

13
12
TIPS ON OPERATION TIPS ON INGREDIENTS
Peach, nectarines, apricot, plum, mango, etc.
Remove hard seeds from the ingredients
before juicing.
Hard seeds
Pineapple, melon, mango, orange, etc.
Peel the skin from the ingredients before juicing.
Hard or
inedible
skins
Frozen strawberry, blueberry, raspberry, etc.
Completely thaw frozen fruits before juicing.
Do not use ice.
Frozen
fruits or ice
Sesame seed, butter, margarine, etc.
Do not extract ingredients containing vegetable
or animal oil. This can reduce performance and
even damage the maXtractor™.
Vegetable/
animal oil
Coconut, sugarcane, whole grains, etc.
Do not extract ingredients with no water
content.
Others
The Slow MaXtractor™ is an innovative product that uses a patented
slow-speed masticating technology to eciently extract the juice from
ingredients. The maXtractor™ is designed to obtain the best result
from ingredients with rm composition and with high water content.
For best result, each ingredient should be prepared and extracted
depending on its characteristics and properties.
Experience the best quality juice by understanding each ingredient’s characteristics
and knowing the optimal way of handling them.
1. Operating the maXtractor™ without ingredients can cause damage to the
UltraSqueezer™.
2. Do not continuously operate the maXtractor™ for more than 30 minutes.
This can damage the motor from overheating.
After continuous use, let the maXtractor™ rest for 30 minutes to cool down before starting
another session.
3. Do not put ngers or other objects into the hopper. Always use provided pusher
when needed.
If other objects are inserted into the hopper during operation, such materials can get stuck and
damage the maXtractor™ parts and/or cause injury.
4. Do not put dried or hard ingredients like whole grains, fruits with hard seeds or ice
into the maXtractor™.
These may damage the parts (e.g. juicing bowl, UltraSqueezer™, and strainer).
• Beans or grains can be used if soaked overnight or boiled.
• Fruits with pits and hard seeds must be pitted before juicing (e.g. nectarines, peaches, mangoes
and cherries).
• When using frozen fruits with small seeds such as grapes, completely thaw before inserting
them into the maXtractor™.
5. Do not use ingredients containing excessive amounts of vegetable oil or animal fat.
Do not use the maXtractor™ to extract vegetable oil from ingredients.
If vegetable/animal oil gets on the UltraSqueezer™, it may reduce performance and even damage
the part.
6. Do not reinsert the extracted pulp into the maXtractor™. This can cause the unit to
stop or cause the hopper not to open.
7. After juicing ingredients with seeds like grapes, thoroughly clean all the crevices on
the bottom of the UltraSqueezer™.
DO NOT
put the following ingredients into the maXtractor™:
MaXtractor™ damage due to owner negligence or from not following the instructions of this manual will void
the warranty.

15
14
INGREDIENTS PREPARATION
Hard fruits and
vegetables may put
excess strain onto the
motor and cause it to
stall.
Soak in cold water
prior to juicing and
cut to appropriate
sizes.
To increase the juice
yield, juice fruits and
vegetables with high
water content.
PREPARATION TIPS:
• Slice the ingredients 1 inch thick or cut 1 inch wide and 2-6 inches long.
• Soak hard ingredients like carrots and ginger in cold water prior to juicing.
EXTRACTION TIPS:
• Slowly insert the ingredients, one at a time.
• Pace the juicing speed ensuring each ingredient is thoroughly extracted.
• To maximize the juice yield, juice with ingredients with high water content.
PREPARATION TIPS:
• Cut 1-4 wedges.
EXTRACTION TIPS:
• Slowly insert the ingredients, one piece at a time.
• Use the pusher to push the ingredients down the hopper. (The pusher also helps prevent juice from
spraying out of the hopper when extracting ingredients with high water content)
• Leave the smart cap open when juicing ingredients that create excessive foam during extraction.
(Foam can accumulate if operated with the smart cap closed).
• It is recommended that the extracted juice be consumed within 48 hours after extracting. Depending
on the density of the ingredients, the extracted juice can gradually show layers over time.
• If there is an excessive amount of foam, use a mesh strainer to separate it from the juice.
• When an ingredient is being masticated by the UltraSqueezer™, the squeezed ingredient may splash
juice through the hopper. Use the pusher to block out the juice splash when juicing.
| (E.g. apples, oranges & tomatoes)
Before
Operating: How to Use the Smart
Cap:
Juice Yield:
Adjusting
the amount
of pulp in
the juice:
• Before Operating: If the maXtractor™ is jammed or if the hopper does not
open, press the REVERSE button and hold until the ingredient becomes
dislodged. Repeat REVERSE-OFF-FORWARD as needed.
• Continue operating the maXtractor™ until all the ingredients in the juicing
bowl are extracted. The hopper may not open easily if there is a lot of pulp
remaining in the maXtractor™.
• Every ingredient yields dierent amounts of juice.
• Juicing with the smart cap closed allows mixed juice creations with dierent
fruits, vegetables and liquids.
• After juicing, close the smart cap to block excess juice from dripping,
especially when disassembling the juicing bowl o the base.
• When making dierent juices, quickly rinse away any leftover avors by
running a glass of water in the maXtractor™ with the smart cap closed.
• Leave the smart cap open when juicing ingredients that create excessive
foam during extraction (e.g. apples, celery).
• Pay close attention when operating the maXtractor™ with the smart cap
closed. Juice may overow if the amount collected in the bowl exceeds its
capacity marked.
• For the optimal extraction and maximum juice yield, cut the ingredients
following the guidelines given in this section.
• Insert ingredients slowly monitoring how they are extracted.
The juice yield may vary depending on the juicing speed.
• Depending on the ingredient, you may get extra pulp when juicing
continuously.
• To reduce the amount of pulp, disassemble the top-set and wash frequently.
Soft fruits and vegetables
(e.g. oranges, tomatoes):
Hard fruits and vegetables
(e.g. carrots, potato, beets & spinach):
- Peel the skin o oranges, and for tomatoes and
apples, take out the stem.
- If the ingredients are larger than the hopper, cut
the ingredients into pieces that will fit into it.
- Fruits with seeds must be pitted before extraction.
Cut to 1-4 wedges then slowly insert the ingredients
down the hopper.
1-4 wedges
6 inch
1/2 - 1 inch
1 inch

17
16
4 inches
If the hopper does not open due to excessive amount of small seeds left in the juicing bowl,
continuously run the maXtractor™ for 30 second to extract any leftover seeds. If the hopper is still
stuck, repeat REVERSE - OFF- FORWARD until the ingredients become dislodged. Then twist the
hopper to open while pushing downwards with palms. (Depending on the ingredient, pour some
water down the hopper for quick rinsing to help dislodging).
• The bers from tough ingredients like celery can wrap around the juicing UltraSqueezer™
and aect maXtractor™’s performance. Cut the stems that are thick and tough to 4 inches long
or less.
• Foam can build up from juicing brous ingredients. Use strainer to remove the foam before
serving.
• For ingredients like pineapple, slice o the rind of the pineapple and cut around the brous
core. Cut the esh of the pineapple to smaller pieces.
• Recommended amount of juicing per session is 500g. When juicing more than 500g, wash the
top-set before continue juicing.
INGREDIENTS PREPARATION
Slowly insert ingredients with small seeds to prevent clogging the strainer.
| (E.g. apples, oranges & tomatoes)
Ingredients with small seeds
(e.g. raspberry, pomegranate, grape):
Fibrous ingredients like celery and kale should be cut into small lengths before juicing
| (E.g. apples, oranges & tomatoes)
Fibrous and/or tough leafy ingredients
(e.g. celery, kale, pineapple):
Insert ingredients slowly
to minimize the amount
of leftover seeds in the
strainer.
When juicing leafy
ingredients like celery and
kale, do not collect more
than 500g per session. For
best result, disassemble
and wash the top-set
before juicing again.
If leafy ingredients
wrap around the juicing
UltraSqueezer™,
open the hopper and
remove the bers
before continue
juicing.
It’s best to juice with
ingredients with higher
amount of uid, like
apples or carrots.
Carrots, apples : brous
ingredients = 9:1
[recommended ratio]
For best result, juice with
ingredients with higher
amount of uid(e.g. apple,
pear)
PREPARATION TIPS:
• When juicing frozen ingredients, make sure they are completely thawed (e.g. raspberry, strawberry).
• Rinse ingredients thoroughly. Remove all stems.
• For pomegranate, discard the skin and juice only the inner part.
EXTRACTION TIPS:
• Depending on the size of the grape, insert 3-5 grapes at a time while monitoring the extraction result.
• Thaw frozen ingredients, like pomegranate and raspberry, then insert about 1 tablespoon (5g) at a time.
• Frozen ingredients usually lose signicant amount of uid from thawing. When juicing, mix milk or
yogurt to balance the uid lost.
PREPARATION TIPS:
• Soak brous ingredients in cold water for about 30 minutes before cutting them.
• Separate each stem. Cut the outer stems that are thick and tough to 4 inches long or less.
EXTRACTION TIPS:
• One at a time, slowly insert the prepared ingredients.
• Insert more ingredients after the previously ones have been completely extracted.
①
Roll leaves in spiral as inserting into the maXtractor™.
②
Insert the leafy part of the ingredients rst then alternate between leafy parts and stems.
③
For ingredients like cilantro or wheatgrass, grab a handful and insert in a bundle.
Caution |
Caution |

19
18
HOW TO DISASSEMBLE AND CLEAN
Note |
• Soak the juicing bowl in a solution of
warm water with baking soda or little bit
of bleach to clean the excess buildup.
Tip |
• It is not necessary to completely
clean the maXtractor™ when making
multiple juices during a single juicing
session.
• When nished juicing, always
disassemble and clean thoroughly to
prevent residue buildup.
Tip |
Clean the base with a soft damp towel
and dry.
Remove the UltraSqueezer™, strainer and
rotation wiper unit from the juicing bowl.
Clean with provided brush.
Note |
Tip |
Note |
Under running water, clean the outside of
the UltraSqueezer™ with a dish scrub. Use
the tip of the cleaning brush to push out
any residue in the crevices on the bottom
of the part.
With the smart cap closed, ll the
juicing bowl with water and turn on
the maXtractor™.
Let it run for a moment. Open the
smart cap and let the water run out
of the juicing bowl.
Turn the hopper counter clockwise to
open.
Turn the top-set counter clockwise and
lift o the base.
Note | • If the towel is dripping wet, make sure
to squeeze out the excess liquid before
using it on the maXtractor™.
• After juicing ingredients with seeds, make
sure to thoroughly clean the bottom
crevice of the UltraSqueezer™. If this area
isn’t properly cleaned, it can aect the
balance between the UltraSqueezer™ and
the strainer and damage the parts.
• Extract all the remaining pulp in the
juicing bowl before stopping the
maXtractor™.
• For easier clean up, operate the
maXtractor™ for an additional 30 seconds
after the juice is extracted.
• When the hopper is stuck, press the
REVERSE – OFF – FORWARD button in
this order, switching back and forth 2 to
3 times to dislodge. Then place hands on
the lower part of the hopper and rmly
press down simultaneously turning the
hopper counter clockwise to open.
Note | • When moving the appliance, do not
lift by grabbing the hopper. Always lift
the appliance by grabbing the base or
handle.
• Thoroughly clean the UltraSqueezer™
ensuring that it is clean without any residue.
• Completely dry before using.
• Immediately clean the maXtractor™
after each use. If remaining residue in
the maXtractor™ dries up, it can make
disassembling and clean-up difficult.
The excess buildup can cause poor
performance in future uses.
• For easier disassembly, place the top-set
in the sink and run water through the top-
set.
• Thoroughly dry the bottom of the
UltraSqueezer™ where it connects to the
metal cylinder shaft on the base.
Switch OFF and unplug the power cord
from the wall outlet.
1
1 4 6
7
Place the juicing bowl under running
water and unplug the compression
silicone to clean the pulp spout.
5
2
3
1
2
* The products illustrated/photographed in this booklet may vary slightly from the actual product.
Quick Rinsing

21
20
HOW TO USE THE CLEANING TOOL
Hold the cleaning tool with one hand and insert
the strainer into the tool.
Under running water, rotate the cleaning
tool and the strainer in opposite directions to
clean.
Thoroughly rinse the inside and outside of
the strainer under running water.
After cleaning, remove the strainer from the
cleaning tool. Dry before storing.
HOW TO CLEAN SILICONE PARTS
Silicone Brushes
Pull out the Silicone brushes from
the rotation wiper to clean.
After cleaning, insert into the slot
with the tail pointing down as
shown in the illustration.
Compression Silicone
Unplug to clean.
After cleaning, rmly insert into
the slot below the pulp spout.
Silicone Ring
Remove the silicone ring from the
juicing bowl to clean.
After cleaning, push in the silicone
ring with the smaller surface facing
down.
Smart Cap
Remove from the juice spout
to clean.
After cleaning, insert the silicone
piece into the smart cap and
attach the cap into the juice spout.
Clean the rotation wiper under running water.
Thoroughly dry after cleaning. Before assembling the top-set, ensure that the compression
silicone and silicone ring are rmly inserted.
The cleaning tool makes clean-up quick and easy.
Completely dry after cleaning.
If the compression silicone and silicone ring are not rmly inserted, juice may leak through the
bottom of the juicing bowl.
Use the included cleaning brush to remove hard-to-reach bits after using the cleaning tool.
Tip | Tip |
Note |
Note |
* The products illustrated/photographed in this booklet may vary slightly from the actual product.
1
1
4
2
3
Note | Insert the strainer until you hear a click.

23
22
TROUBLESHOOTING Q&A
When there is no power to the maXtractor™:
• Check if the power cord is properly plugged in.
• Check if the hopper and the juicing bowl are
properly assembled.
• Check if the top-set and the base are properly
assembled.
• MaXtractor™ will not operate if parts are not
assembled properly.
Low juice yield:
• Each ingredient has dierent amounts of liquid
that will yield dierent amounts of juice.
• If the ingredients are not fresh, they may contain
reduced amounts of uid, which will yield less
juice.
• Check if the compression silicone is rmly
inserted.
• If the ingredient itself has low water content, it
may help to soak it in water before juicing.
• If juicing ingredients with small seeds, after a
few servings, it may reduce the juice yield. For
best results, disassemble and wash the top-set in
between juicing.
• If there is seed residue on the bottom of the
strainer, this can aect maXtractor™ performance
and the overall juice yield.
There is too much pulp in the juice:
• When continuously juicing, and depending on the
ingredient, the juice may contain a lot of ne pulp.
• To reduce the ne pulp, clean the top-set
frequently and extract the pulp.
• Use a mesh strainer and put the juice through it
to collect the unwanted pulp.
• If the strainer and the UltraSqueezer™ are
damaged and aecting the maXtractor™’s
performance, it is recommended the parts be
replaced.
*The lifetime of each part may vary depending
on length and method of use and ingredients
extracted.
• If too many ingredients are inserted at the same
time, it may cause the maXtractor™ to stop
frequently. This can lead to pulpy juice. Insert the
ingredients slowly and few at a time.
The hopper will not close:
• Make sure the UltraSqueezer™ is pushed all the
way in to the strainer in order for the hopper to
close properly.
Odd noise from the maXtractor™:
• Check if the parts are assembled correctly.
Try reassembling the parts and listen for the odd
noise.
• Do not start the maXtractor™ unless there are
ingredients and/or liquid in it.
• Operating the maXtractor™ without ingredients
can cause damage to the UltraSqueezer™.
• The friction noise from the UltraSqueezer™ and
the strainer will disappear when ingredients are
inserted into the maXtractor™.
• If the noise occurs when ingredients are inserted
into the maXtractor™, check the size of the
ingredients. Do not insert anything over 1 inch in
thickness.
• Depending on the type of ingredients, the
dimensions can be smaller.
• The noise can occur if the maXtractor™ is operated
on an uneven or slanted surface. Place the
maXtractor™ on a horizontally at surface when
operating.
The extracted pulp is very moist:
• During the very beginning of extraction, the pulp
can be more moist.
• Depending on the ingredient’s condition,
especially when the ingredient is not fresh, the
juice can be extracted with the pulp.
• Select fresh ingredients.
During operation, the juicing bowl shakes.
• The UltraSqueezer™ and the strainer are set up
to crush and squeeze the ingredients. It is normal
for the UltraSqueezer™ and the strainer to vibrate.
• If the ingredient contains strong ber, the
vibration from the top-set may be stronger.
During juicing, the maXtractor™ stopped:
• Check the power cord and make sure it is plugged
in correctly.
• Check that all the parts are correctly assembled.
• If too many ingredients are inserted at one time,
this can cause the maXtractor™ to stop.
• When the maXtractor™ stops because there are
too many ingredients inserted in it, press the
REVERSE - OFF - FORWARD button in this order,
switching back and forth 2 to 3 times.
• The reverse setting will push the ingredients up,
and the forward setting will pull the ingredients
down.
• If the maXtractor™ stops due to the overload
protection, let it cool for 30 minutes to 2 hours
before juicing again.
• If there are hard seeds within the ingredients,
remove them before juicing. Hard seeds can
damage the maXtractor™.
Layers of separation in the juice:
• Depending on the density of the ingredients,
the extracted juice may show layers of dierent
juices. It is dierent from separation due to
oxidation caused by juicing with a high-speed
maXtractor™.
The hopper is stuck:
• After juicing, let the maXtractor™ operate for
another 30 seconds to extract the remaining
pulp.
• If there is too much pulp in the top-set, this can
cause the hopper to not open. In this situation,
press the REVERSE OFF - FORWARD button in this
order, switching back and forth 2 to 3 times.
• Pour water down the hopper to rinse out the
inside and then try opening the hopper.
Juice dripping down the body of the base:
• If the compression silicone on the bottom of the
juicing bowl is not plugged in correctly, the juice
may seep out on to the maXtractor™ base. Before
assembling the parts, check and make sure the
compression silicone is plugged in correctly.
Is it possible to juice ingredients with
tough ber?
• Ingredients like celery or ginger contain long
bers that may wrap around the UltraSqueezer™
and aect the maXtractor™’s performance. When
juicing brous ingredients, do not collect more
than 0.5 liter of juice. After collecting this quantity
or less, clean the top-set completely before
juicing again.
Discoloration of the plastic parts:
• After juicing, if the maXtractor™ is not cleaned
right away, the remaining pulp inside the top-
set can dry up which can make disassembling
and cleaning hard. This can also aect the
maXtractor™’s performance and color.
• Ingredients that are rich in carotenoids such as
carrots and spinach may dye plastic parts. When
this occurs, rub vegetable oil in to the dyed areas
and use mild detergent to clean.
• Vegetable oil should only be used during clean-
up for parts that are discolored. Do not use
vegetable oil on the UltraSqueezer™ or the
strainer. If vegetable oil or animal fat gets on the
UltraSqueezer™ or the strainer, this can aect the
maXtractor™’s performance and may result in
damaged parts.
• The silicone pieces on the top-set can be
detached to be thoroughly cleaned.
Using for purposes other than juicing:
• This maXtractor™ is designed to juice ingredients
like fruits and vegetables.
• Do not use the maXtractor™ for extracting
vegetable oil.
• Do not juice ingredients with high contents of
vegetable/ animal oil.
• If vegetable/animal oil gets on the UltraSqueezer™
or the strainer, this can aect the performance
of the maXtractor™ and could result in damaged
parts.

24
MANUAL DE USO Y CUIDADOMANUA
L
SPECIFICATIONS
Voltage
Power Consumption
Maximum Use
Weight
Dimension
Manufacturer
Type
AC120V, 60Hz
240W
Less than 30 min
15 lbs (6.8kg)
7.2 x 9.5 x 18.3 inch (184 x 242 x 466mm)
NUC Electronics Co., Ltd.
Low speed
Product
Model
maXtractor™
ULD-322NB, ULD-325NB

28 Medidas importantes de seguridad
29 Precauciones de seguridad
30 Partes
32 Instrucciones de ensamblaje
34 Instrucciones de uso
36 Consejos de uso
37 Consejos sobre ingredientes
38 Preparación de ingredientes
42 Instrucciones para desarmar y limpiar
44 Instrucciones para limpiar las piezas de silicona
45 Instrucciones para usar el accesorio para limpiar
46 Solución de problemas: Preguntas y respuestas
48 Especicaciones
CONTENIDO
Antes de usar el producto, lea todas las instrucciones
incluidas en este manual.

29
28
• Este aparato ha sido diseñado para uso doméstico solamente. Por favor siga cuidadosamente
las instrucciones incluidas en este manual. (Este aparato no estará cubierto bajo la garantía del
fabricante, si es utilizado de cualquier manera que sea diferente a la especicada por el mismo,
o si se le da un uso comercial).
• Guarde este manual de uso para futuras referencias.
• Si el aparato es ofrecido como regalo, por favor incluya este manual junto con el producto.
Las siguientes precauciones son provistas para asegurar el bienestar del usuario. Por favor léalas
cuidadosamente y tenga cuidado cuando use el producto.
Advertencia: Esta señal advierte sobre el riesgo de lesiones severas e incluso la muerte.
Cuidado: Esta señal advierte sobre el riesgo de lesiones o daños severos al producto.
Prohibido No desarmar Debe actuar
MEDIDAS IMPORTANTES DE SEGURIDAD PRECAUCIONES DE SEGURIDAD
No utilice soluciones
químicas peligrosas
para limpiar el
aparato: Esto pudiese
descolorarlo o incluso
causar un incendio.
No desarme la base ni
haga reparaciones o
modicaciones al aparato:
Esto pudiese causar
que deje de funcionar
correctamente y
causar incendios,
descargas eléctricas
o lesiones.
No utilice este aparato
sobre supercies
desniveladas: Esto
pudiese causar que el
aparato no funcione
correctamente si se
llegara a caer.
No mantenga o
utilice este aparato
cerca de infantes
o niños pequeños:
Hacer esto, pudiese
causarles lesiones.
No rocíe agua
o soluciones
inflamables cerca del
aparato: Esto pudiese
causar una explosión
o descarga eléctrica.
Desconecte el cable
del tomacorriente
cuando el producto
no esté siendo usado.
No coloque las partes
de su maXtractor™ en
el lavaplatos o en agua
demasiado caliente:
Esto pudiese desgastar
las partes más rápido.
No introduzca sus
dedos ni otros
objetos en la tolva
mientras el aparato
esté en uso: Esto
pudiese ocasionar
lesiones.
MEDIDAS IMPORTANTES DE SEGURIDAD
Cuando se utilizan aparatos eléctricos, siempre deben seguirse precauciones básicas de seguridad.
1 Lea todas las instrucciones.
2 Para reducir el riesgo de descargas eléctricas, no coloque la base del motor en agua ni en cualquier
otro líquido.
3 Cuando el aparato esté siendo usado por niños o cerca de ellos, se requiere una supervisión atenta.
4 Desconecte el aparato del tomacorriente cuando no esté siendo usado, antes de ensamblarlo,
desarmarlo o cuando vaya a limpiarlo.
5 Evite tocar las partes que estén en movimiento.
6 No use el aparato si nota que el cable o el enchufe están dañados, ni tampoco si el aparato está
funcionando incorrectamente o se ha dañado en forma alguna. Envíelo al Centro de Servicio para
que sea revisado y/o reparado.
7 El uso de accesorios que no han sido recomendados o vendidos por el fabricante pudiesen
ocasionar un incendio, descargas eléctricas o lesiones personales.
8 Este aparato ha sido diseñado solamente para uso doméstico.
9 No permita que el cable cuelgue de una mesa o mostrador.
10 Antes de encender la unidad, asegúrese de que la tolva esté correctamente cerrada. No el abra
mientras el aparato está siendo usado.
11 Una vez que termine de usar el aparato, asegúrese de que el interruptor se encuentre en la posición
de “OFF”. Fíjese que el motor se haya detenido completamente antes de desarmar el aparato.
12 No introduzca sus dedos ni otros objetos en la tolva mientras el aparato esté en uso. Si algún
alimento llegara a atascarse, utilice la pieza para empujar o un pedazo de fruta o verdura para
presionar el alimento atorado. Si al hacer esto, el alimento sigue atascado, apague el motor y
desarme el maXtractor™ para remover los residuos de alimentos.
13 No use el aparato si la unidad giratoria está dañada.
14 No utilice el aparato sin antes colocar el recipiente para la pulpa en su lugar.
15 No altere ni modique el aparato de manera alguna.
16 Solamente use este aparato tal y como se especica en este manual.
17 Este aparato debe usarse durante periodos de tiempo limitados.
GUARDE ESTAS INSTRUCCIONES

31
30
PARTES
*Los productos ilustrados/fotograados en este manual pudiesen ser ligeramente distintos al producto real.
PASO 1
Ensamblaje de la parte superior
PASO 2
Ensamblaje de la parte superior a la base
Alinee los puntos rojos de las piezas que
componen la parte superior y ensámblelas
cómo se indica en el gráco. Luego gire la
tolva (ya ensamblada) en dirección de las
manecillas del reloj para cerrarla.
Una vez que tenga la parte superior
armada, conéctela a la base del
maXtractor™, asegurándose de que la
echa incluida en la tolva
▼
esté alineada
con la echa de la base, identicada
como OPEN . Gire ligeramente la parte
superior en dirección de las manecillas del
reloj, hasta asegurarse de que su echa
▼
esté alineada con la echa de la base,
identicada como CLOSE .
9. UltraSqueezer™8. Colador
10.
Pieza para empujar
7. Unidad giratoria
11. Cepillo para limpiar
Pieza para empujar
Alinee
Alinee los puntos rojos
●
e
inserte la pieza para empujar.
+
+
+
+
+
+
+
+
2. Tazón
3. Recipiente
para la pulpa
6. Recipiente
para el jugo
4.Tapa inteligente
5. Base
1. Tolva
Removible

33
32
INSTRUCCIONES DE ENSAMBLAJE
Inserte rmemente el tapón de silicona
en la ranura interna del canal de
expulsión de la pulpa
El jugo pudiese gotear si no está
correctamente ensamblado.
Nota |
El UltraSqueezer™ necesita estar puesto en
su lugar para que la tolva se pueda cerrar.
Para facilitar el ensamblaje, sostenga
la tolva y gírela tal como se indica en
el gráco.
El maXtractor™ no funcionará si es que sus
partes no se encuentran correctamente
ensambladas.
Nota |
Nota |
PASO 1
Ensamblaje de la parte superior
PASO 2
Ensamblaje de la parte superior con la base.
Inserte el colador en la unidad giratoria,
luego colóquela en el tazón –asegúrese
de que los puntos rojos
●
, que se incluyen
en ambas partes, estén alineados-.
Inserte el UltraSqueezer™ en el colador.
Presiónelo hacia abajo hasta que calce
correctamente.
Coloque la tolva en el tazón, de manera
que los puntos rojos de cada parte
●
estén
alineados. Gire la tolva en dirección de las
manecillas del reloj para cerrarla. El punto
rojo de la tolva deberá quedar alineado con
la señal identicada como CLOSE .
Antes de usar
el maXtractor™
• Lave todas las partes antes de ser usadas por primera vez.
• Asegúrese de que tanto el tapón como el aro de silicona estén instalados
correctamente.
1
2
3
4
5
Una vez que tenga la parte superior armada,
conéctela a la base del maXtractor™,
asegurándose de que la echa incluida en
la tolva
▼
esté alineada con la echa de
la base, identicada como OPEN . Gire
ligeramente la parte superior en dirección de
las manecillas del reloj, hasta asegurarse de
que su echa
▼
esté alineada con la echa
de la base, identicada como CLOSE .
7
Coloque el recipiente para la pulpa
debajo del canal de expulsión de la
misma. Asimismo, coloque el recipiente
para el jugo bajo su canal de expulsión,
tal como se muestra en el gráco.
Consejo
Coloque la parte superior sobre la base.
6
Open
Close
Removible

35
34
Utilice la tapa inteligente para preparar
jugos combinados, impedir que el jugo siga
cayendo o para enjuagar el tazón cuando
prepare diferentes jugos.
Una vez que el jugo y la pulpa hayan sido completamente exprimidos,
apague la unidad.
INSTRUCCIONES DE USO
Una vez que tenga los ingredientes listos, conecte el cable (enchufe)
al tomacorriente.
Presione el interruptor en la opción FORWARD para que el aparato
empiece a funcionar.
Introduzca los ingredientes listos, uno a la vez.
• Evite agarrar el cable con las manos mojadas. Esto podría producir una descarga
eléctrica, un cortocircuito o un incendio.
• Revise que el tomacorriente sea seguro.
• Opción FORWARD: Empuja los ingredientes hacia abajo y los tritura lentamente.
• Opción REVERSE: Empuja los ingredientes hacia arriba para desobstruirlos.
• Si los ingredientes que quedaron en el tazón no han sido completamente exprimidos, la
tolva pudiese no abrir fácilmente. Después de cada exprimida, deje que el maXtractor™
funcione por 30 segundos más para que el aparato pueda procesar la pulpa sobrante.
• Si la tolva se llegara a atascar, presione el interruptor en este orden: REVERSE–OFF-FORWARD.
Repita el mismo procedimiento de 2 a 3 veces hasta que los ingredientes se desatoren. Luego
coloque sus manos sobre la parte inferior de la tolva y presione rmemente hacia abajo,
mientras la gira en dirección opuesta de las manecillas del reloj para abrirla.
» Dependiendo de los ingredientes usados, vierta agua por la tolva para enjuagar la
parte interna del tazón y luego intente retirar la tolva.
• Deje la tapa inteligente abierta cuando esté exprimiendo ingredientes que
producen espuma excesiva al ser procesados (por ejemplo: manzanas, apio).
• Preste mucha atención cuando esté exprimiendo con la tapa inteligente cerrada.
El jugo pudiese derramarse si llegara a exceder la capacidad indicada en el tazón.
• REVERSE: Empuja los ingredientes hacia arriba para desobstruirlos. La opción de
REVERSE funciona solamente mientras se mantenga presionado el interruptor.
• Presione el interruptor en la opción OFF para asegurarse que el maXtractor™ se
haya detenido completamente. Luego mantenga presionada la opción REVERSE
de 2 a 3 segundos y deje de presionarla. Repita este paso las veces que sean
necesarias. Espere a que el maXtractor™ se detenga completamente antes de usar
la opción REVERSE, para evitar que funcione incorrectamente.
• Si el maXtractor™ no llegase a funcionar luego de estos pasos, desármelo y limpie
todas sus partes antes de volverlo a usar.
Si el maXtractor™ dejara de funcionar mientras esté siendo usado:
Presione el interruptor en la opción OFF. Luego mantén-
galo presionado en REVERSE hasta que los ingredientes
se desobstruyan.
Repita los pasos de REVERSE–OFF-FORWARD tantas veces
sean necesarias hasta conseguir el resultado deseado.
Opción FORWARD: Empuja los
ingredientes hacia abajo y los tritura
lentamente.
Opción OFF: Hace que el aparato se
detenga.
Opción REVERSE: Empuja los ingre-
dientes hacia arriba para desobstruirlos.
Nota |
Nota |
Nota |
Nota |
Nota |
Consejos |
Consejos |
Nota |
Si los ingredientes se llegaran a atorar en el UltraSqueezer™ y la tolva no se abre, presione el
interruptor en la opción de apagado “OFF”. Luego mantenga presionado el interruptor en
REVERSE hasta que el ingrediente se desobstruya. Repita los pasos de REVERSE–OFF-FORWARD
las veces que sean necesarias hasta conseguir el resultado deseado.
PASO 1 PASO 3
PASO 4
PASO 5
PASO 2
▶▶▶
4
1 3
2
OFF OFFREVERSE FORWARD
• Verduras de hojas brosas (apio —celery—, col rizada —kale—, etc.):
» Separe cada tallo. Corte los extremos duros y gruesos en pedazos de hasta 4 pulgadas
(10 cm) de largo.
» Agrupe las hojas de las verduras mientras las va insertando en el maXtractor™.
• Antes de empezar a procesar los ingredientes, retire las semillas y pepas duras.
• Cuando vaya a procesar frutas congeladas que tengan semillas pequeñas, asegúrese de
que incluso estas semillas se hayan descongelado completamente.
• Introduzca un ingrediente a la vez.
• Alinee los puntos rojos
●
e inserte la pieza para empujar.
• Una vez que haya colocado los ingredientes, utilice la pieza para empujar cuando sea nece-
sario. Tenga en cuenta que si usa esta pieza en exceso, la calidad del jugo pudiese variar.
» Use ocasionalmente la pieza para empujar cuando esté exprimiendo ingredientes
suaves como tomates y manzanas. El uso constante de esta pieza al procesar
ingredientes suaves pudiese afectar la calidad del jugo.
• Usar el maXtractor™ con la tapa inteligente puesta permite crear una variedad de jugos,
cuando se escogen diferentes frutas y verduras, leche, bananas, frijoles, etc.
• Luego de usar el maXtractor™, cierre la tapa inteligente para impedir que el jugo siga
cayendo, sobre todo cuando vaya a retirar el tazón de la base.
• Cuando prepare diferentes clases de jugos, cierre la tapa inteligente y pase un vaso de
agua por el maXtractor™ para enjuagar rápidamente los sabores restantes.
Tapa inteligente

37
36
CONSEJOS DE USO CONSEJOS SOBRE INGREDIENTES
Duraznos, nectarinas, melocotones, ciruelas,
mangos, etc. Retire las semillas duras de estos
ingredientes antes de exprimirlos.
Semillas
duras
Piña, melón, mango, naranja, etc.
Antes de exprimir estos ingredientes,
pele sus cáscaras.
Cáscaras
duras o no
comestibles
Fresas, moras azules ( blueberries ), frambuesas
congeladas, etc. Antes de exprimirlas,
descongélelas completamente. No use hielo.
Frutas
congeladas
o hielo
Ajonjolí, mantequilla, margarina, etc.
No exprima ingredientes que contengan grasas
animales o vegetales. Esto puede afectar el
desempeño del maXtractor™ e incluso dañarlo.
Grasas
vegetales
o animales
Coco, caña de azúcar, granos integrales, etc.
No exprima ingredientes sin contenido líquido.
Otros
El maXtractor™ es un producto innovador que usa una tecnología
patentada para triturar lentamente los ingredientes y extraer su
jugo de manera eciente. Ha sido diseñado para obtener el mejor
resultado, tanto de ingredientes de consistencia firme como de
aquellos con alto contenido de agua.
Para obtener los mejores resultados, cada ingrediente debe
ser preparado y exprimido de acuerdo a sus características y
propiedades.
Para poder disfrutar de jugo de la mejor calidad,
entienda las características de cada ingrediente y
conozca la manera óptima de usar cada uno de ellos.
1. Dejar el maXtractor™ funcione sin ingredientes puede dañar el UltraSqueezer™.
2. No utilice el maXtractor™ por más de 30 minutos seguidos.
Esto pudiese ocasionar que el motor se recaliente. Luego de usar el maXtractor™ por un periodo
continuo, déjelo reposar por 30 minutos para que se enfríe antes de comenzar una nueva sesión.
3. No meta los dedos o cualquier objeto en la tolva.
Siempre utilice la pieza provista para
presionar cuando sea necesario. Si cualquier otro objeto es introducido en la tolva mientras se
esté usando, dichos materiales pudiesen llegar a atorarse y dañar las partes del maXtractor™ y/o
causar lesiones.
4. No ponga ingredientes secos o duros como granos integrales, frutas con semillas duras o
hielo dentro del maXtractor™. Esto pudiese dañar las partes del maXtractor™ (por ejemplo: el
tazón, el UltraSqueezer™ o el colador)
• Puede usar frijoles o granos, siempre y cuando los haya dejado remojando desde el día
anterior o los haya hervido.
• Retire las semillas o pepas duras de las frutas, antes de ser exprimidas (por ejemplo:
nectarinas, duraznos, mangos y cerezas).
• Cuando use frutas congeladas con semillas pequeñas como uvas, descongélelas
completamente antes de pasarlas por el maXtractor™.
5. No use ingredientes que contengan cantidades excesivas de aceite vegetal o grasa animal.
No use el maXtractor™ para exprimir aceite vegetal de ingredientes. Si grasas vegetales o
animales llegan al UltraSqueezer™, pudiesen reducir su desempeño e incluso dañarlo.
6. No vuelva a introducir la pulpa extraída en el maXtractor™. Esto pudiese hacer que la
unidad deje de funcionar o impedir que la tolva se abra.
7. Luego de exprimir ingredientes con semillas como uvas, limpie detalladamente todas las
hendiduras en el asiento del UltraSqueezer™.
NO ponga los siguientes ingredientes en el maXtractor™:
Si el maXtractor™ es dañado por negligencia del usuario o por no seguir las instrucciones en este manual, la
garantía quedará anulada.

39
38
PREPARACIÓN DE INGREDIENTES
Las frutas y verduras
duras pueden hacer
que el motor trabaje
excesivamente y, por
lo tanto, este deje de
funcionar.
Remójelas en agua
fría, antes de pasarlas
por el maXtractor™
y luego córtelas en
pedazos apropiados.
Para incrementar
la cantidad de
jugo, utilice frutas
y verduras que
contengan grandes
cantidades de agua.
CONSEJOS PARA PREPARARLOS:
• Rebane los ingredientes en cortes de 1 pulgada (2.5 cm) de grosor o córtelos en pedazos de 1
pulgada (2.5 cm) de ancho y de 2 a 6 pulgadas (5 cm -15 cm) de largo.
• Antes de procesarlos, remoje los ingredientes duros como las zanahorias y el jengibre en agua fría.
CONSEJOS PARA EXPRIMIR:
• Inserte lentamente los ingredientes, uno a la vez.
• Siga la velocidad del maXtractor™, asegurándose de que cada ingrediente está siendo exprimido
completamente.
• Para maximizar las cantidades de jugo, exprima ingredientes que contengan grandes cantidades
de agua.
CONSEJOS PARA PREPARARLOS:
• Córtelos en 1 a 4 rebanadas
Consejos para exprimir:
• Inserte lentamente los ingredientes, uno a la vez.
• Empuje los alimentos usando la pieza para presionar. (Esta pieza también evita que el jugo de los
alimentos con alto contenido de agua, que está procesando, salpique).
• Deje la tapa inteligente abierta cuando esté exprimiendo ingredientes que producen excesiva espuma
al ser procesados (La espuma puede acumularse si se usa el maXtractor™ con la tapa inteligente cerrada).
• Se recomienda que el jugo exprimido sea consumido dentro de 48 horas después de haber sido
preparado. De acuerdo a la densidad de los ingredientes, el jugo exprimido puede gradualmente
mostrar capas al pasar el tiempo.
• Si el jugo contiene una cantidad excesiva de espuma, use un colador de malla (mesh strainer) para
retirar dicha espuma.
• When an ingredient is being masticated by the juicing UltraSqueezer™, the squeezed ingredient may
splash juice through the hopper. Use the pusher to block out the juice splash when juicing
| (E.g. apples, oranges & tomatoes)
Antes de
empezar
a usar el
maXtractor™:
Cómo usar
la tapa
inteligente:
Cantidades
de jugo:
Para ajustar
la cantidad
de pulpa en
el jugo:
• Antes de empezar a usar el maXtractor™: Si los ingredientes se llegaran a
atorar y la tolva no se abre, presione el interruptor en la opción de apagado
“OFF”. Luego mantenga presionado el interruptor en REVERSE hasta que el
ingrediente se desobstruya. Repita los pasos de REVERSE–OFF-FORWARD las
veces que sean necesarias hasta conseguir el resultado deseado.
• Continúe usando el maXtractor™ hasta que todos los ingredientes que
se encuentren el tazón sean exprimidos. Puede ser que la tolva no abra
fácilmente, si hay un montón de pulpa restante dentro del maXtractor™.
• Cada ingrediente rinde diferentes cantidades de jugo.
• Usar el maXtractor™ con la tapa inteligente cerrada permite crear una variedad
de jugos combinados, cuando se escogen diferentes frutas, verduras y líquidos.
• Luego de usar el maXtractor™, cierre la tapa inteligente para impedir que el
jugo siga cayendo, sobre todo cuando vaya a retirar el tazón de la base.
• Cuando prepare diferentes clases de jugos, pase un vaso de agua por el
maXtractor™ para enjuagar rápidamente los sabores restantes con la tapa
inteligente cerrada.
• Deje la tapa inteligente abierta cuando esté exprimiendo ingredientes que
producen espuma excesiva al ser procesados (por ejemplo: manzanas, apio).
• Preste mucha atención cuando esté exprimiendo con la tapa inteligente cerrada.
El jugo pudiese derramarse si llegara a exceder la capacidad indicada en el tazón.
• Para obtener la mayor y óptima cantidad de jugo, corte los ingredientes de
acuerdo a cómo se indica en esta sección.
• Introduzca los ingredientes lentamente, mientras vigila como están siendo
exprimidos.
• La cantidad de jugo pudiese depender de la velocidad de la extracción.
• De acuerdo al ingrediente, puede que obtenga más pulpa mientras continúa
exprimiendo.
• Para reducir la cantidad de pulpa, desarme la parte superior y lávela con
frecuencia.
Frutas y verduras suaves
(Ejemplos: naranjas y tomates):
Frutas y verduras duras
(Ejemplos: zanahorias, papas, remolacha (betabel) y espinaca):
6 pulgadas
½ pulgada
(1.27 cm) –
1 pulgada
(2.5 cm)
1 pulgada (2.5 cm)
- Pele la cáscara de las naranjas. En el caso de
tomates y manzanas, retire el cabo.
-Si los ingredientes son más grandes que la
entrada de la tolva, córtelos en pedazos que
entren adecuadamente.
-
Retire las semillas de las frutas, antes de
exprimirlas. Córtelas en 1 a 4 rebanadas y
luego insértelas lentamente en la tolva.
1-4 wedges