RT-Wave EV-L2R5803 User manual

It’s About Real-Time
RT-Wave Wireless Elevator Video System
EV-L2R5803 Manual Rev-A
OWNER’S MANUAL

WIRELESS ELEVAT R CAMERA SYSTEM REV. A
2
Table of Contents
SAFETY NOTICES.……………………………………………………………………………………………………....3
INTRODUCTION……..…………………………………………………………………………………………………..4
PRE INSTALLATION…………………………………………………………………………………...……………….5
Site Evaluation….………………..…...……………………………………………….………………...5
Tools Required…….………..………...……………………………..………………………………...…6
Camera Parts List………..…………………………………………………………………………….…7
Preparing Camera for Installation….………………………………………………………………....
CORNER- OUNT CA ERA INSTALLATION………………………………...……………………………………9
ADJUSTING CA ERA FOCUS & TILT…...………………………………………………………………………...11
SECURING CA ERA FACEPLATE……….……………………………………………………………………...…12
SECURING POWER & VIDEO CABLES TO CAB………..…………………………….…………………………..13
OPENING & CLOSING THE ALL WEATHER ENCLOSURE……………………….………………..…………..14
OUNTING THE TRANS ITTER……...…………………………………………………………………………....15
VIDEO CABLE CONNECTION TO TRANS ITTER…...………………………………………………………….16
CONNECTING O NI-DIRECTIONAL ANTENNAS……...……………………………………………..…………17
POWER SUPPLY CONNECTION TO TRANS ITTER…….………..…………………………………………….18
AC/DC Power Terminal Input………………………………………………………...…………..19
ESD Lightning Surge Protection Feature………………………………………………………..19
UN-USED GRO ETS & SEALS…..…………………………………………………………………………...……20
OUNTING THE RECEIVER…...……………………………………………………………………………………21
VIDEO CABLE CONNECTION TO RECEIVER……………………………………………………………………22
POWER SUPPLY CONNECTION TO RECEIVER…………………………………………………………….……23
AC/DC Power Terminal Input………………………………….………………………………....24
ESD Lightning Surge Protection Feature….…………………..……...………………………...24
ON-SCREEN VIDEO ADJUST ENTS…………..…………………………..………………………………………..25
Setup Menu………………………………….…………………………………………………….….25
Input Selection………………………………………………………….……………………………26
Output Selection………………………………………………………..……………………………27
Miscellaneous…………………………………………………………..……………………………2
Picture Setup…………………………………………………………………………………………29
WARRANTY INFOR ATION & RETURNS………………………………………….…….…………………….....30

WIRELESS ELEVAT R CAMERA SYSTEM REV. A
3
Safety Notice
I. THIS DEVICE CO PLIES WITH FCC RULES PART 15. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITONS:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference, including interference that
may cause undesired operation of the device
II. This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
III. In order to comply with the FCC/IC adopted RF exposure requirements, this transmission system will
be installed by a professional installer. Installation of all antennas must be performed in a manner that
will provide at least 2.4 feet clearance from the front radiating aperture, to any member of the public.
IV. This is NOT an intrinsically safe device. Do not take into an area where intrinsic safety is required.
Bodily harm may result if warning is ignored.
V. DO NOT OPERATE TRANS ITTER OR RECEIVER WITHOUT ANTENNAS CONNECTED TO
ANTENNA PORTS. Failure to do so will result in damage to the unit and void the warranty.
VI. DO NOT OPERATE THE RT-WAVE SYSTE WHEN the transmitter and receiver are closer than
10 feet to each other. The devices may not work properly and permanent damage can occur.
VII. The RT-WAVE has been certified by the FCC for use with other products without any further
certification (as per FCC section 2.1091).
Warning: Changes or modifications not expressly approved by VideoComm Technologies could void the
user’s authority to operate the equipment
FCC ID: SU5-MSR-RTWAVE INDUSTRY CANADA ID: 3 7A-MSR
SSID #

WIRELESS ELEVAT R CAMERA SYSTEM REV. A
4
Introduction
Introduction
The industry's only wireless elevator camera system delivers Real-Time, DVD quality encrypted digital
video up to 200 Floors. Featuring a revolutionary pre-configured plug-and-play design, the system does not
require software setup or programming, minimizing installation time and maximizing results. Choose this
wireless system for the most extreme elevator surveillance applications.
Advantages
• Revolutionary pre-configured plug & play design
• Transmits Real-Time DVD quality video up to 200 Floors
• Digital immunity to signal interference
• Lightning fast hardware based MPEG-4 encoder & decoder
• Industry leading 5-tier input power management system
• 64 Bit encrypted data stream (optional 128 bit)
• Automatic system pairing and on screen status display
• No connections to the elevator mechanics or traveling cable
• No maintenance or inspections required
• Deters vandalism, trespassing & other criminal behavior
• Easily identify employees, residents, and visitors
• FCC & IC approved for license free use
SECURITYSTORES INC.
Customer Service
Bus [phone]
US Toll Free [phone]
Fax [phone]
E-mail- [e-mail]
Web Site- www.wirelesselevatorcamera.com
Monday - Friday 8:30am- 5:30pm
Eastern Standard Time

WIRELESS ELEVAT R CAMERA SYSTEM REV. A
5
Pre-Installation
Site Evaluation
The following must be determined prior to installation:
Power Source
The transmitter, receiver and corner-mount camera will each require a power source.
Ensure there is a 115 Volt electrical outlet available on the rooftop of the elevator cab;
this outlet will power both the transmitter and corner-mount camera.
A 115 Volt AC electrical outlet will also be required at the receiver location in the pit.
Cabling routes
Hardwiring the video cable from the receiver to your monitoring location will be required;
consider this in determining whether your receiver will be mounted in the elevator pit
or in the mechanical penthouse.
Clearances
The transmitter and receiver location must be clear of any moving mechanisms including but not
limited to traveling cable, counter-weight, cabling trough, guide rails, brakes, door mechanics,
sensors and safety devices.
Line-of-Sight
Consider the path that the wireless video will travel between the transmitter and receiver.
Line-of –sight is defined as a clear and unobstructed view between the transmitter and receiver.
This will determine where you will mount the transmitter (roof or under-carriage of elevator cab)
and the receiver (mechanical penthouse or elevator pit).
Every elevator installation is unique – These guidelines may or may not apply to your particular application.
For additional application design assistance contact SECURITYSTORES INC. Customer Service
SECURITYSTORES INC.
Customer Service
Bus [phone]
US Toll Free [phone]
Fax [phone]
E-mail- [e-mail]
Web Site- www.wirelesselevatorcamera.com
Monday - Friday 8:30am- 5:30pm
Eastern Standard Time

WIRELESS ELEVAT R CAMERA SYSTEM REV. A
6
Tools Required
The Wireless Elevator Camera System is designed to be “Plug & Play”
and simple to install with minimal tools. The following is a list
of recommended tools to setup your system.
Drill - Used to create holes for the mounting bracket screws and the video cable,
which will be fed through the roof of the elevator cab.
Drill Bits - Standard drill bit set and ¾” hole saw (used for drilling hole through the roof of the cab)
Wire Stripper – For preparing power wires.
Philips Screw Driver – Used for unscrewing the front cover of the IP-67 enclosure to gain access to video,
audio and power terminations.
Micro-Phillips Screw Driver – Used for adjusting the focus on the camera lens
Metric 20mm Socket & Wrench (Closest Imperial Si e – 13/16”) – Used to tighten or loosen the larger all
weather cable glands. Do not use pliers as they may cause damage to the cable glands
Metric 13mm Socket & Wrench (Closest Imperial Si e – 5/8”) – Used for tightening or loosening the single
small all weather cable gland. Do not use pliers as they may cause damage to the cable glands
Hand Held LCD Monitor – Recommended for verifying video images at input to transmitter
and output from receiver. Perfect for camera angle and focus adjustment.
Multimeter – Measures voltage output, amperage, resistance and cable continuity.
Do Not Use Pliers - The pliers rigid grip may cause permanent damage to the cable glands
on the all weather IP-67 enclosure.

WIRELESS ELEVAT R CAMERA SYSTEM REV. A
7
Camera Parts List

WIRELESS ELEVAT R CAMERA SYSTEM REV. A
8
Preparing Camera for Installation
Use the security key to remove three security screws
on the camera faceplate. Remove the camera faceplate from
camera and mounting bracket.
Use the security key to remove four
security screws from the camera’s protective dome.
Remove the dome.
Remove camera shroud from lens.

WIRELESS ELEVAT R CAMERA SYSTEM REV. A
9
Using a Phillips screwdriver, remove the four screws from the camera base plate (Figure A)
and remove base plate from the triangular mounting bracket (Figure B).
Figure A Figure B
Corner- ount Camera Installation
Place mounting bracket in the corner flush
with the desired location. Mark the wall and
ceiling for the location of the mounting
screws. Depending on wall material type,
wall plugs may be required.
Warning: ounting holes no greater than 5mm in diameter
Drill a larger (imperial size 1/2”) hole in the roof behind
the bracket where the video and power cables
will be fed-through.

WIRELESS ELEVAT R CAMERA SYSTEM REV. A
10
Secure mounting bracket to the wall.
From the rooftop of the elevator, connect the 12VDC
power supply to a 115 Volt electrical outlet.
Feed the power barrel jack and 18” of video cable
into the cab through the ½” hole previously drilled in the roof.
Using a Philips screwdriver, re-attach
the camera base plate on to the mounting
bracket using four screws imperial Size 3/32”