RTS IFB-828 User manual

IFB-828
Service Manual
LIT000481000 Rev B © Bosch Security System, Inc 2010 MAY–2010

PROPRIETARY NOTICE
The product information and design disclosed herein were originated by
and are the property of Bosch Security Systems, Inc. Bosch reserves all
patent, proprietary design, manufacturing, reproduction, use and sales
rights thereto, and to any article disclosed therein, except to the extent
rights are expressly granted to others.
COPYRIGHT NOTICE
Copyright 2010 by Bosch Security Systems, Inc. All rights reserved.
Reproduction, in whole or in part, without prior written permission from
Bosch is prohibited.
WARRANTY NOTICE
See the enclosed warranty card for further details.
CUSTOMER SUPPORT
Technical questions should be directed to:
Customer Service Department
Bosch Security Systems, Inc.
12000 Portland Avenue South
Burnsville, MN 55337 USA
Telephone: [phone]
Fax: [phone]
[email protected]
Technical Questions EMEA
Bosch Security Systems Technical Support EMEA
http://www.rtsintercoms.com/contact_main.php
RETURN SHIPPING INSTRUCTIONS
Customer Service Department
Bosch Security Systems, Inc. (Lincoln, NE)
Telephone: [phone]
Fax: [phone]
Factory Service: 800-553-5992
Please include a note in the box which supplies the company name,
address, phone number, a person to contact regarding the repair, the type
and quantity of equipment, a description of the problem and the serial
number(s).
SHIPPING TO THE MANUFACTURER
All shipments of product should be made via UPS Ground, prepaid (you
may request from Factory Service a different shipment method). Any
shipment upgrades will be paid by the customer. The equipment should
be shipped in the original packing carton. If the original carton is not
available, use any suitable container that is rigid and of adequate size. If
a substitute container is used, the equipment should be wrapped in paper
and surrounded with at least four (4) inches of excelsior or similar
shock-absorbing material. All shipments must be sent to the following
address and must include the Proof of Purchase for warranty repair.
Upon completion of any repair the equipment will be returned via
United Parcel Service or specified shipper, collect.
Factory Service Department
Bosch Security Systems, Inc.
8601 East Cornhusker Hwy.
Lincoln, NE 68507 U.S.A.
Attn: Service

Table
of
Contents
IFB-828 Description ..................................................................................................................................................3
Installation in an RTS Digital Matrix ........................................................................................................................3
Using the IFB-828 as a Simple Program Interface with 4020 and 4030 Belt Packs ................................................6
Specifications .............................................................................................................................................................7
IFB-828 Mechanical Assembly Parts ........................................................................................................................8
90007094005 / 90007094006 .................................................................................................................................................8
IFB-828 PC Board Electrical Parts ..........................................................................................................................8
90307094000 ...........................................................................................................................................................................8
Drawings .................................................................................................................................................................11
Notes ........................................................................................................................................................................13

IFB-828 Description
The IFB-828 interfaces up to eight (8) RTS Systems’ Model IFB-325, 4020, or 4030 IFB Belt Packs to any RTS Digital Matrix
Intercom System, and it provides power to the belt packs.
The IFB-828 may also be used as a simple program interface to feed two (2) separate program sources to each of eight (8)
4020 or 4030 belt packs (16 program sources to eight (8) belt packs total).
Installation in an RTS Digital Matrix
To install an IFB-828 in an RTS Digital Matrix, do the following:
1. Mount the IFB-828 in an equipment rack or bay.
It should be positioned near eye level when sitting or standing to permit adjustment of the IFB program levels and to
check the power indicator lights. There are no special ventilation requirements.
IMPORTANT: IFB-828 Location. The XLR connector outputs from the IFB-828 provide unbalanced audio and DC
operating power to IFB belt packs. Therefore, very long cable runs (over several hundred feet) from the
IFB-828 to the belt packs may result in diminished performance due to DC resistance in the cabling and
noise induced by surrounding equipment. Select a location for the IFB-828 that is as close as possible to
the belt packs, or use appropriate precautions (shielded cable, heavier gauge stranded wire, routing
away from unshielded equipment, etc.) For broadcast application you will typically locate the IFB-828
in the audio booth near the talent location, and no special precautions are required.
2. Select 110 for 110/120V, 50/60Hz operation.
OR
Select 220 for 220/240V, 50/60Hz operation.
3. Connect a 25-pair telco cable to J9 on the back of the IFB-828.
FIGURE 1. IFB-828 Reference View

4. Run this cable to the audio distribution point for the intercom system (punch blocks, etc.).
5. Using AZedit, configure the IFBs for your system.
6. Assign the IFBs to the appropriate keypanel keys.
7. For each IFB you set up:
a. Connect from the output port of the matrix (defined in step 5) to an available IFB input of the IFB-828.
Make the connects at the audio distribution point where you have connected the cable from J9 of the IFB-
828. See Table 1 on page 5 for pin numbers.
b. Connect the IFB program audio source both to the intercom port that you defined as the program input port
of the matrix (in step 5) AND also connect the IFB program audio source to the direct program input of the
selected channel of the IFB-828.
8. Connect from the appropriate 3-pin XLR output connector of the IFB-828 to the LINE (or LINES) connector of the
IFB belt pack. Typical cable wiring is shown in Figure 2 on page 6.
NOTE: In the factory-default configuration, the IFB-325 belt packs receive IFB audio on pin 3 of its XLR connector.
In this configuration, the belt pack’s internal shorting plug J3 is set to pins 2 and 3 shorted. This is not the
correct configuration for use with the IFB-828. To change the setting, open the belt pack and reset the J3
shorting plug so that pins 4 and 5 are shorted. Refer to the IFB-325 User Manual (P/N 93507448000) for
further information.
9. Connect an earset to the IFB belt pack. The Model IFB-325 accepts only monaural earsets. The models 4020 and
4030 accept either monaural or stereo earsets. However, for the standard application of the IFB-828, only a monaural
earset is required.
Monaural Earset Pin Out:
Tip: IFB audio and direct program mix.
Sleeve: Common
Stereo Earset Pin Out:
Tip: IFB audio and direct program mix (interrupt)
Ring: Direct program audio (non-interrupt)
Sleeve: Common
10. Set all belt pack volume controls and all level controls on the IFB-828 to minimum.
11. Plug in the IFB-828 power cord.
The main power on the front panel should light, and each channel LED should light indicating that power is being
supplied to the belt pack output on that channel. Ensure that the matrix is operation and that all program sources are
operational.
12. During normal operation (no IFB interrupts activated) have each talent position adjust their belt pack volume control
for a comfortable program listening level.
Use the interrupt control on a Model 4020or 4030 belt pack.
13. For each IFB:
a. Activate the keypanel key assigned to the IFB.
The program audio should be interrupted at the associated IFB belt pack, and the mic audio from the
keypanel becomes audible.
b. While the IFB key is active, adjust the appropriate level control on the front panel of the IFB-828 to mix the
desired amount of direct program audio back into the keypanel’s mic audio signal.
When the key is released, the mic audio should cut off, and the normal program audio level restores.

5
TABLE 1. Input Connector Pin Out (J9)
Pin Numbers Description
+ Input - Input
1 26 Channel 1 direct program input
2 27 Channel 1 IFB input (from Matrix)
3 28 No connection
4 29 Channel 2 direct program input
5 30 Channel 2 IFB input (from Matrix)
6 31 No Connection
7 32 Channel 3 direct program input
8 33 Channel 3 IFB input (from Matrix)
9 34 No Connection
10 35 Channel 4 direct program input
11 36 Channel 4 IFB input (from Matrix)
12 37 No Connection
13 38 Channel 5 direct program input
14 39 Channel 5 IFB input (from Matrix)
15 40 No Connection
16 41 Channel 6 direct program input
17 42 Channel 6 IFB input (from Matrix)
18 43 No Connection
19 44 Channel 7 direct program input
20 45 Channel 7 IFB input (from Matrix)
21 46 No Connection
22 47 Channel 8 direct program input
23 48 Channel 8 IFB input (from Matrix)
24 49 No Connection
25 50 No Connection

6
Using the IFB-828 as a Simple Program Interface with 4020 and 4030 Belt Packs
Use Table 1 on page 5 and the cable wiring in Figure 2 to connect one (1) or two (2) program sources to each IFB-828 channel.
In this application, each direct program input at the IFB-828 feeds to the non-interrupt channel of the belt pack, and the level is
adjusted by the NON-INTERRUPT control on the belt pack; each IFB input feeds to the interrupt channel and is adjusted by
the INTRRUPT control. The control on the IFB-828 front panel can be used to mix the NON-INTERRUPT audio into the
INTERRUPT audio.
FIGURE 2. IFB Belt Pack Interconnect Cable Wiring Diagram

7
Specifications
Dimensions
19” wide x 1.75” high x 7.5” deep (483mm x 44.5mm x 191mm)
Input Power Requirements
110/120 or 220/240 VAC, 50/60Hz selectable via a back panel switch
Audio Inputs
Type: Balanced (transformer coupled)
Level: +4 to +8dBu
Impedance: Approximately 600 Ohms
Audio Outputs
Type: Unbalanced
Level: -10 to -6dBu
Output Power (each IFB belt pack channel)
+24VDC, 160mA, not to exceed 750mA total.
Connectors
Input (J9)
Type: 50-pin telco
Pin Out: see Table 1 on page 5
Outputs (J1 to J8)
Type: 3-pin male XLR
Pin 1: Audio and DC Common
Pin 2: +IFB Audio (interrupt audio) and +24VDC
Pin 3: +Direct program audio (non-interrupt audio)

8
IFB-828 Mechanical Assembly
Parts
90007094005 / 90007094006
IFB-828 PC Board Electrical
Parts
90307094000
QTY Description Part Number
1 Transformer, Subassembly 90207094000
1 CONN D HDWE KIT=KY 8800102463
1 A/C CORD/CONN 18GA 8800102668
1 A/C ENTRY MODULE 8800117313
9 CONN. 100SP 2POS 24 8800127838
1 FUSE 630mA 5MMX 20M PAS000130000
1 LED 5V GN PNL MNT W 8800131495
2 IDE PNL 7” 8800144463
8 KNOB POINTER 15MM 8800156636
8 KNOB 15MM 1/4 SHFT 8800157458
8 LED GRN PNL MNT 8800191073
1 COVER 7” TOP/BTM 8800218428
8 KNOB CAP 15MM BLK 8800243720
1 PCB ASSY IFB POWER 90307094000
1 FRONT PANEL IFB828 90707094000
1 REAR PANEL IFB828 90807094000
1 BOTTOM PANEL 91007094000
Ref
Des Description Part No.
C1 CAPACITOR, EL, 1000 UF, 50V PAS000104004
C2 CAPACITOR, CN, 0.1 UF, 50V 52676-613
C11 CAPACITOR, EL, 10 UF, 50V 51821-639
C12 CAPACITOR, CM, 0.1 UF, 50V 52676-613
C13 CAPACITOR, EL, 10 UF, 50V 51821-639
C21 CAPACITOR, EL, 10 UF, 50V 51821-639
C22 CAPACITOR, CM, 0.1 UF, 50V 52676-613
C23 CAPACITOR, EL, 10 UF, 50V 51821-639
C31 CAPACITOR, EL, 10 UF, 50V 51821-639
C32 CAPACITOR, CM, 0.1 UF, 50V 52676-613
C33 CAPACITOR, EL, 10 UF, 50V 51821-639
C41 CAPACITOR, EL, 10 UF, 50V 51821-639
C42 CAPACITOR, CM, 0.1 UF, 50V 52676-613
C43 CAPACITOR, EL, 10 UF, 50V 51821-639
C51 CAPACITOR, EL, 10 UF, 50V 51821-639
C52 CAPACITOR, CM, 0.1 UF, 50V 52676-613
C53 CAPACITOR, EL, 10 UF, 50V 51821-639
C61 CAPACITOR, EL, 10 UF, 50V 51821-639
C62 CAPACITOR, CM, 0.1 UF, 50V 52676-613
C63 CAPACITOR, EL, 10 UF, 50 V 51821-639
C71 CAPACITOR, EL, 10 UF, 50 V 51821-639
C72 CAPACITOR, CM. 0.1 UF, 50 V 52676-613
C73 CAPACITOR, EL, 10 UF, 50 V 51821-639
C81 CAPACITOR, EL, 10 UF, 50 V 51821-639
C82 CAPACITOR, CM, 0.1 UF, 50 V 52676-613
C83 CAPACITOR, EL, 10 UF, 50 V 51821-639
D1 DIODE, BRIDGE, 2A, 1000V,
BR810DF 558011-000
D11 DIODE, 1N4004, 400 V 50745-005
D13 DIODE, 1N4004, 400 V 50745-005
D21 DIODE, 1N4004, 400 V 50745-005
D22 DIODE, 1N4004, 400 V 50745-005
D23 DIODE, 1N4004, 400 V 50745-005
D31 DIODE, 1N4004, 400 V 50745-005
D32 DIODE, 1N4004, 400 V 50745-005
D33 DIODE, 1N4004, 400 V 50745-005
D41 DIODE, 1N4004, 400 V 50745-005
D42 DIODE, 1N4004, 400 V 50745-005
D42 DIODE, 1N4004, 400 V 50745-005
D51 DIODE, 1N4004, 400 V 50745-005
D52 DIODE, 1N4004, 400 V 50745-005
D53 DIODE, 1N4004, 400 V 50745-005
D61 DIODE, 1N4004, 400 V 50745-005
D62 DIODE, 1N4004, 400 V 50745-005
D63 DIODE, 1N4004, 400 V 50745-005
D71 DIODE, 1N4004, 400 V 50745-005
D72 DIODE, 1N4004, 400 V 50745-005
D73 DIODE, 1N4004, 400 V 50745-005
D81 DIODE, 1N4004, 400 V 50745-005
D82 DIODE, 1N4004, 400 V 50745-005
D83 DIODE, 1N4004, 400 V 50745-005
J1 CONNECTOR, RA XLR, M-3 59892-003
J2 CONNECTOR, RA XLR, M-3 59892-003
J3 CONNECTOR, RA XLR, M-3 59892-003
Ref
Des Description Part No.

9
J4 CONNECTOR, RA XLR, M-3 59892-003
J5 CONNECTOR, RA XLR, M-3 59892-003
J6 CONNECTOR, RA XLR, M-3 59892-003
J7 CONNECTOR, RA XLR, M-3 59892-003
J8 CONNECTOR, RA XLR, M-3 59892-003
P1 CONNECTOR, ST POLARIZED,
0.100, M-2 57763-402
P2 CONNECTOR, ST POLARIZED,
0.100, M-2 57763-402
P3 CONNECTOR, ST POLARIZED,
0.100, M-2 57763-402
P4 CONNECTOR, ST POLARIZED,
0.100, M-2 57763-402
P5 CONNECTOR, ST POLARIZED,
0.100, M-2 57763-402
P6 CONNECTOR, ST POLARIZED,
0.100, M-2 57763-402
P7 CONNECTOR, ST POLARIZED,
0.100, M-2 57763-402
P8 CONNECTOR, ST POLARIZED,
0.100, M-2 57763-402
P9 CONNECTOR, ST POLARIZED,
0.100, M-2 57763-402
P10 CONNECTOR, ST LOCKING,
0.156, M-3 57762-503
R1 RESISTOR, CF, 1.8K OHM, 5%,
1W 52154-629
R2 RESISTOR, CF, 1.2K OHM, 5%,
1/2W 52154-456
R3 RESISTOR, CF, 1.2K OHM, 5%
1/2W 52154-456
R4 RESISTOR, CF, 1.2K OHM, 5%
1/2W 52154-456
R5 RESISTOR, CF, 1.2K OHM, 5%
1/2W 52154-456
R6 RESISTOR, CF, 1.2K OHM, 5%
1/2W 52154-456
R7 RESISTOR, CF, 1.2K OHM, 5%
1/2W 52154-456
R8 RESISTOR, CF, 1.2K OHM, 5%
1/2W 52154-456
R9 RESISTOR, CF, 1.2K OHM, 5%
1/2W 52154-456
R11 POTENTIOMETER, 100 OHM,
10%, 1W 523015-000
R12 RESISTOR, MF, 2.26K OHM,
1%, 1/2W 54054-226
Ref
Des Description Part No.
R13 RESISTOR, MF, 124 OHM, 1%,
1/4W 54042-124
R14 RESISTOR, WW, 10 OHM, 10%,
5W 50155-011
R21 POTENTIOMETER, 100 OHM,
10%, 1W 523015-000
R22 RESISTOR, MF, 2.26K OHM,
1%, 1/2 W 54054-226
R23 RESISTOR, MF, 124 OHM, 1%,
1/4W 54042-124
R24 RESISTOR, WW, 10 OHM, 10%,
5W 50155-011
R31 POTENTIOMETER, 100 OHM,
10%, 1W 523015-000
R32 RESISTOR, MF, 2.26K OHM,
1%, 1/2 W 54054-226
R33 RESISTOR, MF, 124 OHM, 1%,
1/4W 54042-124
R34 RESISTOR, WW, 10 OHM, 10%,
5W 50155-011
R41 POTENTIOMETER, 100 OHM,
10%, 1W 523015-000
R42 RESISTOR, MF, 2.26K OHM,
1%, 1/2 W 54054-226
R43 RESISTOR, MF, 124 OHM, 1%,
1/4W 54042-124
R44 RESISTOR, WW, 10 OHM, 10%,
5W 50155-011
R51 POTENTIOMETER, 100 OHM,
10%, 1W 523015-000
R52 RESISTOR, MF, 2.26K OHM,
1%, 1/2 W 54054-226
R53 RESISTOR, MF, 124 OHM, 1%,
1/4W 54042-124
R54 RESISTOR, WW, 10 OHM, 10%,
5W 50155-011
R61 POTENTIOMETER, 100 OHM,
10%, 1W 523015-000
R62 RESISTOR, MF, 2.26K OHM,
1%, 1/2 W 54054-226
R63 RESISTOR, MF, 124 OHM, 1%,
1/4W 54042-124
R64 RESISTOR, WW, 10 OHM, 10%,
5W 50155-011
R71 POTENTIOMETER, 100 OHM,
10%, 1W 523015-000
R72 RESISTOR, MF, 2.26K OHM,
1%, 1/2 W 54054-226
Ref
Des Description Part No.

10
R73 RESISTOR, MF, 124 OHM, 1%,
1/4W 54042-124
R74 RESISTOR, WW, 10 OHM, 10%,
5W 50155-011
R81 POTENTIOMETER, 100 OHM,
10%, 1W 523015-000
R82 RESISTOR, MF, 2.26K OHM,
1%, 1/2 W 54054-226
R83 RESISTOR, MF, 124 OHM, 1%,
1/4W 54042-124
R84 RESISTOR, WW, 10 OHM, 10%,
5W 50155-011
T11 TRANSFORMER, AUDIO 559001-000
T12 TRANSFORMER, AUDIO 559001-000
T21 TRANSFORMER, AUDIO 559001-000
T22 TRANSFORMER, AUDIO 559001-000
T31 TRANSFORMER, AUDIO 559001-000
T32 TRANSFORMER, AUDIO 559001-000
T41 TRANSFORMER, AUDIO 559001-000
T42 TRANSFORMER, AUDIO 559001-000
T51 TRANSFORMER, AUDIO 559001-000
T52 TRANSFORMER, AUDIO 559001-000
T61 TRANSFORMER, AUDIO 559001-000
T62 TRANSFORMER, AUDIO 559001-000
T71 TRANSFORMER, AUDIO 559001-000
T72 TRANSFORMER, AUDIO 559001-000
T81 TRANSFORMER, AUDIO 559001-000
T82 TRANSFORMER, AUDIO 559001-000
VR1 IC, VOLTAGE REGULATOR,
LM317 53290-000
VR2 IC, VOLTAGE REGULATOR,
LM317 53290-000
VR3 IC, VOLTAGE REGULATOR,
LM317 53290-000
VR4 IC, VOLTAGE REGULATOR,
LM317 53290-000
VR5 IC, VOLTAGE REGULATOR,
LM317 53290-000
VR6 IC, VOLTAGE REGULATOR,
LM317 53290-000
VR7 IC, VOLTAGE REGULATOR,
LM317 53290-000
VR8 IC, VOLTAGE REGULATOR,
LM317 53290-000
C14 CAPACITOR, CEREMIC DISC,
0.001UF 500V 52157-022
Ref
Des Description Part No.
C24 CAPACITOR, CEREMIC DISC,
0.001UF 500V 52157-022
C34 CAPACITOR, CEREMIC DISC,
0.001UF 500V 52157-022
C44 CAPACITOR, CEREMIC DISC,
0.001UF 500V 52157-022
C54 CAPACITOR, CEREMIC DISC,
0.001UF 500V 52157-022
C64 CAPACITOR, CEREMIC DISC,
0.001UF 500V 52157-022
C74 CAPACITOR, CEREMIC DISC,
0.001UF 500V 52157-022
C84 CAPACITOR, CEREMIC DISC,
0.001UF 500V 52157-022
R10 RESISTOR, MF, 10.0K OHM, 1%
1/2W 54055-100
R15 RESISTOR, MF, 10.0K OHM, 1%
1/2W 54055-100
R16 RESISTOR, MF, 10.0K OHM, 1%
1/2W 54055-100
R17 RESISTOR, MF, 10.0K OHM, 1%
1/2W 54055-100
R18 RESISTOR, MF, 10.0K OHM, 1%
1/2W 54055-100
R19 RESISTOR, MF, 10.0K OHM, 1%
1/2W 54055-100
R20 RESISTOR, MF, 10.0K OHM, 1%
1/2W 54055-100
R25 RESISTOR, MF, 10.0K OHM, 1%
1/2W 54055-100
Ref
Des Description Part No.

11
Drawings
FIGURE 3. 9027-7094-000 (page 1)

12
FIGURE 4. 9027-7094-000 (page 2)

13
Notes