Rugged CCTV Sentry-700 User manual

INSTRUCTION MANUAL
Sentry-700
Dome & Infrared Dome Camera

CONTENTS
1
WARNING & CAUTION 2
GENERAL FEATURES 4
NAME OF EACH PART 6
INSTALLATION 8
CONNECTION 13
SPECIFICATIONS 14
OSD MENU SETTING 18
TROUBLESHOOTING 20
DIMENSIONS 21

If you fail to read this information and handle the product incorrectly, death or
serious injury may occur.
The unit should be installed by the trained Personnel.
Switch off immediately if the product emits smoke or abnormal heat.
Never install the product in area exposed to oil or gas.
Never touch the power cord with wet hands.
Clean only with dry cloth.
Ensure that the product is not subjected to strong impacts and vibration.
Never expose the camera to direct sunlight
Never disassemble the unit by
unauthorized person.
Serious and Permanent
damage will occur.
WARNING
2
WARNING & CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
un-insulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
1. CAMERA
2. MOUNT BRACKET
3. TERMINAL BLOCK
4. DC JACK CABLE
5. CALBLOCK 6x30
8. WRENCH 1.5mm
9. WRENCH 2.5mm
10. MANUAL
6. SCREW 4x25
7. O-RING ( 3.8dx1.9t)
11. TEMPLATE LABEL
1EA
1EA
1EA
1EA
4EA
3EA
1EA
1EA
1EA
(Dual Power Type Only)
7EA
Contents in Box
3
(Dual Power Type Only)
1EA
WARNING & CAUTION

IP-68 rated waterproof frame housing
3-Axis bracket (Ceiling, Flush, Wall mount available)
Compatible with a junction box
Easy installation by mount bracket.
Extra video out available
Powerful Infra-Red LEDs (Built in IR LED Type only)
2.8~12mm or 3.5~16mm TDN Varifocal lens (option)
Wide-ranging power tolerance
Heater (option)
High Resolution
Low Light Sensitivity
An ideal waterproof frame housing suitable for the outdoor circumstance.
This 3-Axis bracket enable you to install easily anywhere.
It can compatible with a junction box, therefore easy to install.
Once you fix the mount bracket on the surface of a wall or the ceiling, the
camera will not fall by holder of the bottom cover.
So it can install the camera easily.
The camera has an Extra Video output jack to check the actual image or
setup of the OSD function.
By adopting powerful Infra-Red LEDs, it can observe clearly even night
time or circumstance of total darkness.
By adopting a filter-changeable TDN(ICR) Varifocal lens, you can get more
clear image.
Dual Power Type : DC10V~30V / AC10V~28V
DC12V Power Type : DC12V 10%
By adopting Heater, this camera suitable for a harsh climate.
(-40 C~+50 C)
By adopting a diagonal 6mm(1/3") SONY EXVIEW HAD CCD II, the
camera produces clear picture quality with a horizontal resolution of
700 TV line color, and 800 TV line B/W (960H Type)
By adapting unique digital processing technology, It can clearly distinguish
the outline and color of a subject in 0.0001Lux(B/W for Sens-up x256) low
illumination environments.
±
oo
4
GENERAL FEATURES

5
SMART 3DNR (3D Digital Noise Reduction + Motion Detection)
F-DNR (Fog Digital Noise Reduction)
D-WDR (Digital Wide Dynamic Range)
SMART D-ZOOM
DIS (Digital Image Stabilizer)
LENS SHADING COMPENSATION
DEFECT
SENS UP
SMART IR
Motion Detection (4 Zone, Alarm output)
Polygon Privacy Masking (8 Zone)
By adopting unique digital processing technology, it can reduces the gain
noise and produce clear, obvious images in low illumination environments.
You will have a distinct image in any severe circumstances: ambient light,
fog, rain, snow, etc.
The D-WDR function illuminates darker areas of an image during retaining
the same light level for brighter areas to even out the overall brightness of
images with high contrast between bright and dark areas.
This will be helpful to cover the limitaion of the focal length of the equipped
lens.
It prevents the unfocused image by shaking and secures the clear image.
LSC corrects the phenomenon where the image gets darkened or blurred
on the periphery.
The DEFECT mode compensates Dead Pixel of the CCD Sensor.
When it is night or dark circumstance, the camera automatically detects
the light level and maintains a clear picture if this mode is operated.
The DSP can control the saturated image caused by close object when IR
LED operating.
Since the camera detects motion and generates signals without any
additional external sensors, you can monitor more efficiently by connecting
an alarm device.
You can easily set up privacy masking areas to be masked unwanted
zones and hide them from display on the screen.
GENERAL FEATURES

6
1. Bubble 100 Phi
2. Top Cover
3. Main Body
4. Bottom Cover
5. Mount Bracket
6. Cover
7. Lens
8. OSD Menu Switch
9. Extra Video Output
10. Cap Screw (PT 3/4)
NAME OF EACH PART(Built in IR LED Type)

7
1. Bubble 100 Phi
2. Top Cover
3. Main Body
4. Bottom Cover
5. Mount Bracket
6. Cover
7. Lens
8. OSD Menu Switch
9. Extra Video Output
10. Cap Screw (PT 3/4)
NAME OF EACH PART(Without IR LED Type)

INSTALLATION
8
1. When you need to install a camera on the surface of a concrete wall, you
can drill a hole like Fig.3 exactly by using a template label offered by
accessory.
2. As Fig.3, please set a calblock in the hole of the wall.
3. Please fix the mount bracket by using screw.
4. After connect with cable (Please refer to the connection part for the cable
connection). Please join holder part of the bottom cover to the arrow
direction on the floor inside of the mount bracket then push and twist to
clockwise. (Refer to Fig.5 & Fig.6)
84mm
46mm
Calblock
( 6x30)
Template Label
Ceiling Mount
Wall Mount
Holder Holder
Seal Taple
Screw
( 4x25)
6mm
Hole Diameter : 6mm
Depth : 30mm

INSTALLATION
9
5. Like Fig.6, please join bottom cover to clockwise until it stops after inserting,
kindly tighten screw on both sides of the mount bracket.
6. After connect Extra Video Connector to the screen, you can place the
camera to desired direction. (For the cable connection, Please refer to
Page.13)
7. Like Fig.7, please open the Cover (push lightly on both sides of the Cover).
After adjust Zoom and Focus by using a Lens Lever, close the Cover.
Please notice a direction on both side of lock part of the cover.
(The size of left and right side are different. If the direction is changed,
the cover will not be fitted.)
NOTE :
Wrench 1.5mm
Zoom Lever
Focus Lever

INSTALLATION
How to install Flush Mount
10
8. After close Groove of Top Cover and Jut of Bottom Cover, please
tighten screws surely to prevent a leak of water.
1. Like Fig.9, Please drill into Bottom Cover to 4.5mm holes of 3pcs by
using drill machine.
2. Please remove plastic holder of 2pcs on the Bottom Cover side.
3. Make a hole of 100mm on the ceiling. Then put the camera into the hole
and please fixing by screw with O-ring.
4. The way of rest installation is the same as previous page.
Holder
Screw
( 4x25)
O-Ring
Drill Dia: 4.5mm
Hole Diameter: 100mm
Wrench 2.5mm

INSTALLATION
How to install Wall Mount Bracket
11
1. When you need to install a camera on the surface of a concrete wall, you
can drill a hole like Fig.10 exactly by using a Template Label offered by
accessory.
2. Please set a Calblock in the hole of the wall.
3. Then stick by screw by using a Junction Box on the surface of a wall.
4. Please join the Bracket to the Junction Box. (Refer to Fig.11)
84mm
46mm
Calblock
( 8x35)
Screw
( 5x35)
Screw M4x60
Nut M4
Template Label 8mm
Hole Diameter : 8mm
Depth : 40mm

INSTALLATION
5. After join a Adapter to the Mount Bracket, please combine the camera by
the same way like explained in the previous.
6. After pass a cable to Wall Mount Bracket, please insert the Camera to
clockwise then screw it.
7. Please wrap and finish the Cable Connector by using a seal tape to
prevent a leak of water.
8. After close the cover of Wall Mount Bracket, please fix by using screws.
12
Screw
(M4x8)
Seal Tape
Wrench 2.5mm
Wrench 2.0mm

*A power source connection is nonpolar.
CONNECTION
DUAL POWER TYPE
1. Terminal Block (Accessory)
2. DC Jack Cable (Accessory)
3. Adaptor (DC12V or AC24V)
4. Video Output (CVBS)
5. Seal Tape
*A power source connection is nonpolar.
DC12V POWER TYPE
1. DC Jack
2.
3. Video Output (CVBS)
4. Seal Tape
Adaptor (DC12V)
CAUTION : After connecting the cable, please make sure bind by using a
Seal Tape to prevent a leak of water.
13

Operating temp./hum.
Storage temp./hum.
Power
Power consumption
IR LED
Lens (option)
Dimension
Weight
-10 C~+50 C (Heater type -40 C~+50 C) / 30%~80% RH
OO OO
-20 C~+60 C / 20%~90% RH
OO
Dual Type(DC:10V~30V, AC:10V~28V)/DC Type(DC12V 10%)
Round 40pcs (30deg)
145mm(W) x 124mm(H)(When Including Bracket Mount)
0.9Kg
IP Rating 68
Dual Type (DC:Max. 7W, AC:Max. 9W) / DC Type (Max. 6W)
DC auto iris lens (2.8~12mm or 3.5~16mm)
ICR Filter change DC auto iris lens (2.8~12mm or 3.5~16mm)
NTSC PAL
Total pixels
Effective pixels
Frequency
ESC
DSP
Sensor
Resolution
Scanning system
Sync
S/N Ratio (Y signal)
Video output
Min. Illumination
White balance
BLC
Gain control
Defect
Smart 3DNR
Day & Night
Privacy
Motion detection
Smart IR
Lens Shading
811(H) x 508(V) 795(H) x 595(V)
768(H) x 494(V) 752(H) x 582(V)
15.734[KHz] (H) / 59.94[Hz] (V) 15.625[KHz] (H) / 50[Hz] (V)
Auto/FLK/Manual(1/60~100,000 sec)
NEXT CHIP HAWK-II
1/3 inch SONY 760H EXVIEW HAD CCD II
650 TV lines (Color), 700 TV lines (B/W)
2:1 Interlace
Internal
More than 52 dB (AGC Off)
0.5Lux at F1.2 (color) / 0.0001Lux (B/W for sense up X256) / 0Lux (IR on)
ATW / AWB / AWC-->SET / MANUAL / INDOOR / OUTDOOR
BLC / HSBLC / Off
Low / Middle / High / Off
CVBS:1.0Vp-p / 75 Composite
Compensation dead pixed of the CCD Sensor
On / Off (3D)
Color / Auto / B/W /EXT
On / Off (Programmable 8 zones)
On / Off (Programmable 4 zones)
On/Off
On/Off
Auto/FLK/Manual(1/50~100,000 sec)
Sens-up
DIS
D-zoom
AUTO(x2~x256) / Off
(Digital Image Stabilizer) On / Off
x1.0~x32
F-DNR(Defog) Auto / Manual / Off
D-WDR (Digital Wide Dynamic Range) Low-Level / High-Level
TV SYSTEM
14
SPECIFICATIONS (Built in IR LED /760H Type)

Operating temp./hum.
Storage temp./hum.
Power
Power consumption
IR LED
Lens (option)
Dimension
Weight
-10 C~+50 C (Heater type -40 C~+50 C) / 30%~80% RH
OO OO
-20 C~+60 C / 20%~90% RH
OO
Dual Type(DC:10V~30V, AC:10V~28V)/DC Type(DC12V 10%)
Round 40pcs (30deg)
145mm(W) x 124mm(H)(When Including Bracket Mount)
0.9Kg
IP Rating 68
Dual Type (DC:Max. 7W, AC:Max. 9W) / DC Type (Max. 6W)
SPECIFICATIONS (Built in IR LED /960H Type)
DC auto iris lens (2.8~12mm or 3.5~16mm)
ICR Filter change DC auto iris lens (2.8~12mm or 3.5~16mm)
NTSC PAL
Total pixels
Effective pixels
Frequency
ESC
DSP
Sensor
Resolution
Scanning system
Sync
S/N Ratio (Y signal)
Video output
Min. Illumination
White balance
BLC
Gain control
Defect
Smart 3DNR
Day & Night
Privacy
Motion detection
Smart IR
Lens Shading
1020(H) x 508(V) 1020(H) x 596(V)
976(H) x 494(V) 976(H) x 582(V)
15.734[KHz] (H) / 59.94[Hz] (V) 15.625[KHz] (H) / 50[Hz] (V)
Auto/FLK/Manual(1/60~100,000 sec)
1/3 inch SONY 960H EXVIEW HAD CCD II
700 TV lines (Color), 800 TV lines (B/W)
2:1 Interlace
Internal
More than 52 dB (AGC Off)
0.4Lux at F1.2 (color) / 0.0001Lux (B/W for sense up X256) / 0Lux (IR on)
ATW / AWB / AWC-->SET / MANUAL / INDOOR / OUTDOOR
BLC / HSBLC / Off
Low / Middle / High / Off
CVBS:1.0Vp-p / 75 Composite
Compensation dead pixed of the CCD Sensor
On / Off (3D)
Color / Auto / B/W /EXT
On / Off (Programmable 8 zones)
On / Off (Programmable 4 zones)
On/Off
On/Off
Auto/FLK/Manual(1/50~100,000 sec)
Sens-up
DIS
D-zoom
AUTO(x2~x256) / Off
(Digital Image Stabilizer) On / Off
x1.0~x32
F-DNR(Defog) Auto / Manual / Off
D-WDR (Digital Wide Dynamic Range) Low-Level / High-Level
TV SYSTEM
15
NEXT CHIP HAWK-II

16
SPECIFICATIONS (Without IR LED /760H Type)
NTSC PAL
Total pixels
Effective pixels
Frequency
ESC
DSP
Sensor
Resolution
Scanning system
Sync
S/N Ratio (Y signal)
Video output
Min. Illumination
White balance
BLC
Gain control
Defect
Smart 3DNR
Day & Night
Privacy
Motion detection
Smart IR
Lens Shading
15.734[KHz] (H) / 59.94[Hz] (V) 15.625[KHz] (H) / 50[Hz] (V)
Auto/FLK/Manual(1/60~100,000 sec)
1/3 inch SONY 760H EXVIEW HAD CCD II
650 TV lines (Color), 700 TV lines (B/W)
2:1 Interlace
Internal
More than 52 dB (AGC Off)
0.5Lux at F1.2 (color) / 0.0001Lux (B/W for sense up X256) / 0Lux (IR on)
ATW / AWB / AWC-->SET / MANUAL / INDOOR / OUTDOOR
BLC / HSBLC / Off
Low / Middle / High / Off
CVBS:1.0Vp-p / 75 Composite
Compensation dead pixed of the CCD Sensor
On / Off (3D)
Color / Auto / B/W /EXT
On / Off (Programmable 8 zones)
On / Off (Programmable 4 zones)
On/Off
On/Off
Auto/FLK/Manual(1/50~100,000 sec)
Sens-up
DIS
D-zoom
AUTO(x2~x256) / Off
(Digital Image Stabilizer) On / Off
x1.0~x32
F-DNR(Defog) Auto / Manual / Off
D-WDR (Digital Wide Dynamic Range) Low-Level / High-Level
TV SYSTEM
Operating temp./hum.
Storage temp./hum.
Power
Power consumption
Dimension
Weight
-10 C~+50 C (Heater type -40 C~+50 C) / 30%~80% RH
OO OO
-20 C~+60 C / 20%~90% RH
OO
Dual Type(DC:10V~30V, AC:10V~28V)/DC Type(DC12V 10%)
145mm(W) x 124mm(H)(When Including Bracket Mount)
0.9Kg
IP Rating 68
Dual Type (DC:Max. 4W, AC:Max. 5W) / DC Type (Max. 3W)
Lens (option)
DC auto iris lens (2.8~12mm or 3.5~16mm)
ICR Filter change DC auto iris lens (2.8~12mm or 3.5~16mm)
811(H) x 508(V) 795(H) x 595(V)
768(H) x 494(V) 752(H) x 582(V)
NEXT CHIP HAWK-II

17
NTSC PAL
Total pixels
Effective pixels
Frequency
ESC
DSP
Sensor
Resolution
Scanning system
Sync
S/N Ratio (Y signal)
Video output
Min. Illumination
White balance
BLC
Gain control
Defect
Smart 3DNR
Day & Night
Privacy
Motion detection
Smart IR
Lens Shading
1020(H) x 508(V) 1020(H) x 596(V)
976(H) x 494(V) 976(H) x 582(V)
15.734[KHz] (H) / 59.94[Hz] (V) 15.625[KHz] (H) / 50[Hz] (V)
Auto/FLK/Manual(1/60~100,000 sec)
1/3 inch SONY 960H EXVIEW HAD CCD II
700 TV lines (Color), 800 TV lines (B/W)
2:1 Interlace
Internal
More than 52 dB (AGC Off)
0.4Lux at F1.2 (color) / 0.0001Lux (B/W for sense up X256) / 0Lux (IR on)
ATW / AWB / AWC-->SET / MANUAL / INDOOR / OUTDOOR
BLC / HSBLC / Off
Low / Middle / High / Off
CVBS:1.0Vp-p / 75 Composite
Compensation dead pixed of the CCD Sensor
On / Off (3D)
Color / Auto / B/W /EXT
On / Off (Programmable 8 zones)
On / Off (Programmable 4 zones)
On/Off
On/Off
Auto/FLK/Manual(1/50~100,000 sec)
Sens-up
DIS
D-zoom
AUTO(x2~x256) / Off
(Digital Image Stabilizer) On / Off
x1.0~x32
F-DNR(Defog) Auto / Manual / Off
D-WDR (Digital Wide Dynamic Range) Low-Level / High-Level
TV SYSTEM
Operating temp./hum.
Storage temp./hum.
Power
Power consumption
Dimension
Weight
-10 C~+50 C (Heater type -40 C~+50 C) / 30%~80% RH
OO OO
-20 C~+60 C / 20%~90% RH
OO
Dual Type(DC:10V~30V, AC:10V~28V)/DC Type(DC12V 10%)
145mm(W) x 124mm(H)(When Including Bracket Mount)
0.9Kg
IP Rating 68
Dual Type (DC:Max. 4W, AC:Max. 5W) / DC Type (Max. 3W)
Lens (option)
DC auto iris lens (2.8~12mm or 3.5~16mm)
ICR Filter change DC auto iris lens (2.8~12mm or 3.5~16mm)
SPECIFICATIONS (Without IR LED /960H Type)
NEXT CHIP HAWK-II

18
OSD MENU SETTING
MENU SUB MENU
LENS
DC
VIDEO
MANUAL
BRIGHTNESS
IRIS SPEED
0~100
0~5
BRIGHTNESS 0~100
SHUTTER AUTO(SHUT.MIN, SHUT.MAX), 1/60(50), FLK, MANUAL(LEVEL1/60, FLK,1/250,1/500,
1/1000,1/2000,1/5000,1/10000,1/20000,1/50000,1/1000000
AGC LOW,MIDDLE,HIGH
SENS-UP OFF
AUTO x2,x4,x6,x8,x10,x12,x14,x16,x24,x32,x64,x128,x256
D-WDR LOW-LEVEL 0~15
HIGH-LEVEL 0~15
BLC
VALUE
AREA
DEFAULT
LOW, MIDDLE, HIGH
SINGLE, DOUBLE
HSBLC
GAIN
MODE
MASK LEVEL
DEFAULT
M. SKIP AREA
0~100
NIGHT ONLY, ALL DAY
0~100
OFF, ON
ATW
AWB
AWC-->SET
MANUAL BLUE
RED
0~100
0~100
INDOOR
OUTDOOR
AUTO
COLOR
DELAY
D-->N(AGC)
N-->D(CDS)
0~15
48~255
0~207
B/W
BURST
IR SMART
ON, OFF
OFF
VALUE
AREA
IR DWDR
EXT DELAY 0~15
OFF
ON
VALUE 0~200
OFF
ON
0~100
POSITION, SIZE
0~15
SMART LEVEL 0~200
SENSITIVITY 0~100
SMART NR
OFF
LEVEL
COLOR GAIN
EDGE GAIN
GAMMA
DEFECT LEVEL
MANUAL
AUTO
0~31
0~10
0~10
USER, 0.05~1.00
0~5
EXPOSURE
BACK LIGHT
WHITE BAL
DAY&NIGHT
SMART 3DNR
F-DNR