Rydeen PVR5D User manual

FHD5900英文说明书(V2.0) BY06E046-0 /规格：210*140MM 120G双胶纸，黑色印刷（12P)
V1.0
PVR5D
Motion Sensing DVR System
Owner’s Manual
PVR5D DVR

micro SD (8G) x1)
<0.3Lux
1920X1080P 30FPS/1280X720P 60FPS/WVGA 848X480
60FPS/VGA 640X480 60FPS
8GB SD card:1080P/78min 720P/130min
1.5,TFT LCD
210mAh
15~85%RH
-10°C~70°C [14°F ~ 158°F]
-10°C~50°C [14°F ~ 122°F]
ParametersItem
01. Lens structure Using full glass composition
02. Sensor American high-definition SENSOR
03. Night vision illumination
04. Video resolution
05. Video file format (H.264 compression) MOV
06. Storage medium micro SD/MMC (maximum support to 32GB SDHC)
07. Video length
08. Motion detection Within 3.5 meters of the trigger recording.
09. The LCD screen
10. Lithium battery
11. Storage temperature
12. Working environment temperature
13. Working environment humidity
Attention:
1. Pictures may be slightly different from the actual product.
2. According to the product configuration you choose, different parts may be added, refer to the actual product.
Unit x1 Main Cable x1
Manual x1 GPS Antenna (optional) Clip x1
Congratulations and thank you for purchasing the RYDEEN PVR5D Portable
DVR System. We hope you will enjoy using this exciting product and trust that
it will make your driving experience more enjoyable and hassle-free.
Please read this Owner ’s Manual carefully before using this product. If you have
any further questions about your PVR5D operation, feel free to call RYDEEN,
Toll Free at 1-877-777-8811(within USA only) for product support, or visit our
website: www.rydeenmobile.com or send email to: [e-mail].
WARNINGS
THE FOLLOWING INSTRUCTIONS ARE INTENDED FOR AUTHORIZED
RYDEEN MOBILE INSTALLERS ONLY.
DAMAGE FROM IMPROPER INSTALLATION WILL VOID THE WARRANTY.
EXCESSIVE SHOCK due to dropping any components in the system or subjecting
it to excessive shock and vibrations may cause malfunction and is not covered by
warranty.
THE MAIN BOX OF THE PVR5D SYSTEM IS NOT WATERPROOF. Avoid exposing it
to rain or other forms of excessive moisture.
Water damage is not covered under the warranty.
The usage of Rydeen PVR5D system should never replace normal operation
and safety precautions needed for reversing a vehicle.
Caution should always be taken in ANY vehicle operation.
WELCOME STATEMENT & WARNINGS SPECIFICATIONS
KIT CONTENTS
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC interference limits for Class B digital
devices for home or vehicle use. These limits are designed to provide more reasonable
protection against harmful interference in a residential installation and are more
stringent than “outdoor” requirements.
Operation of this device is subject to the following conditions:
1. This device may not cause harmful interference;
2. This device must accept any interference received, including interference that may
cause undesired operation.

1. 3M adhesive: used for pasting the bracket to the windowshield;
2. Lens: optical components, for video and camera viewfinder, please keep the lens clean;
3. Lens angle adjustment : adjust the lens angle following your needs;
4. Power key (two functions)
•POWER function: hold for 3 seconds to shutdown, screen ON or OFF by a short press;
•UP function: on 9 grips replay interface or system menu status, press UP button to
select file, during play status, press “UP” to select next file or fast-forward;
5. KEY:(two functions)
•"NEXT" function: on 9 grips replay interface and system menu status, press next button to
select file, during play status, press “NEXT” to select next file or fast-forward;
•"FORMAT" function: on standby mode, press “FORMAT” button for 3 seconds until it shows
“FORMAT,” then it’ll get into SD card format process and with the “di di...” alarming sounds,
after formatting, “FORMAT” will disappear;
6. KEY: (three functions)
•"PLAY" function: press to play the video when the unit is on standby mode;
•"OK" function: on non-record, press button for 3 seconds and it’ll show the menu,
press " "(down) or " "(up) to setup, after settings, press "OK" to save and return back;
•"MIC"press: when recording, turn on MIC, press again, turn off MIC;
7. press: (two functions)
•Record function: used to start recording on any standby record mode or stop recording, the
indication light will twinkle when recording, and will turn off when recording is stopped;
•Timing function: on standby mode, press for 3 seconds to get into time settings, press "up"
and "down" to set date and time, press to get into next setting, after setting’s done, press
to log out and save;
8. Reset button: press to initial a system reset;
9. Heat radiation hole: to keep an appropriate working temperature;
10. Micro SD slot: to insert a SD card;
11. loudspeaker: high quality loudspeaker.
1. Clean the window and choose
a proper position to mount.
2. Tear down the 3M from the
bracket.
3. Paste on the window shield. 4. Installation finished.
How to mount / disassemble & adjust lens angle
1. After installation, simply remove the bracket #2 from #1 to pull out the unit if necessary.
(as shown in picture 1)
2. The lens angle can be adjusted 30 degrees (as shown in picture 2).
(picture 1) (picture 2)
fixed mount
SD card slot
Electrical Connecting Instruction
1. Connect wires to the car BAT, ACC and GND (remember to distinguish BAT, ACC and GND).
2. The other end of the wires connected to the host cable-confirm good connection before moving
to next step.
3. Fix the cables with the wire clips.
4. Mount the unit near to the back mirror to get a better view.
5. Mount position should be far from the position of safety airbag.
6. In order to get better GPS signal, please install the GPS antenna in a horizontal position to
ensure no signal disturbances.
How to install
Note:
please follow this
instruction to avoid
malfunctions.
PRODUCT OVERVIEW INSTALLATION INSTRCUTIONS

On standby status, press " " for 3 seconds to go to the menu, press " " or " " to
select items. Press " " for 3 seconds to confirm selections and press " " to return.
Date / Time
Language
Beep Sound
TV Mode
Setup Date / Time
Date / Time
Language
Beep Sound
TV Mode
Setup
English
Français
Español
Português
Language
[TV Mode] set TV mode: PAL / NTSC;
[Frequency] set frequency source : 50Hz / 60Hz;
[Parking Mode] on/off, on means when ACC is on it comes to parking mode
automatically;
[Default Settings] restore to factory settings: confirm / cancel; (Note: when choosing
"confirm," all parameters will be restored to factory default settings);
[Format] used for storage of SD card format: Yes / No (Note: select "yes" will format the
SD card, remove the card of all documents, please be careful while operating);
[Version] to check the software version of the product.
[G-Sensor] off / low / middle / high;
[Beep Sound] set sound of button-press to be on / off;
[Language] set required language: English, German, French, Italian, Russian,
Portuguese, simplified, traditional Chinese, Japanese, Spanish;
Once get power from car charger, DVR will start automatically and enter into recording state.
ON/ OFF manually
ON/ OFF automatically
Put the SD card into the card slot follow the pointed direction, and you’ll hear a sound "ka."
Press the SD card to pull out the SD card .
When AV out connects to terminal DVD, the monitor of the unit will turn off.
Attention: please format your SD card before usage.
power key
SD card slot
Wiring Diagram
ACC
GND
AV OUT
DVD
BAT
fuse
GPS
Tips
Please make sure to connect the cables to car
Battery & ACC following the sketch,othewise,
may cause parking model to become invalid,
SD card full, file broken or wrong timing etc..
malfunctions.
Turn on the parking model (default is on ).
When ACC is off while recording, the motion detection with high sensitivity parking model will
turn on. Any movements or light changes within 3.5M will trigger recording and it will standby
automatically after 30s with no movement or light change.
When ACC is off while recording, the system will save current recording file and turn off automatically.
When on parking mode, the BAT Voltage Detection is on, once the voltage is under than 11.8V, the
system will save current recording file and turn off automatically.
Parking mode turn on
Parking mode turn off
BAT voltage detection
Connect to DVD
SD card usage
ON: press power supply key to turn ON the unit and the indicator will turn to green;
OFF: press power supply key for 2 seconds to turn OFF the unit and the indicator will turn off;
2015
OPERATION INSTRUCTIONS
MAINTAINING YOUR DVR

Press the "PLAY" key to enter playback mode, press up, down, left, right and then press "OK"
button to play the file, then press the stop button to stop playing. In the process of rewind,
2X, 4X, 8X three kinds of speed are available for fast forward and rewind.
1. The software of specified video player for PC is copied in the SD card. Please copy the software to
your PC before usage and then install the software on your PC.
2. Please access the website (www. rydeenmobile.com) to download and install the software.
1. [No Video and Photo]
Please amend the video or photo resolution, or check whether there is enough space for
the storage card and make sure the storage card is installed correctly;
2. [No signal output to the DVD]
Please confirm whether correctly connected with the DVD, and check whether AV OUT socket
is in the right place;
3. [Video or photo images are not clear]
Please check the lens or automotive glass is not dirt, please use a soft cloth to clean it;
4. [Normal video process state with no light flash or keypad failure]
Please reset the system with the "RESET" key while the system is on, and press "POWER" key
to restart;
5. [ System crushed]
Please enter "MENU" then enter the "default settings" to restore all parameters to factory settings.
(Main menu overview)
After power on and press " " to start recording, white lights will flash. The top left corner of the
screen will show " " (see below picture), press “ ” again to stop recording and save the
current files.During the recording, press" " to open or close the MIC.
The symbol " " indicates voice recording is on, " " means mute.
(1) Video state
(2) WDR is on
(3) G-sensor icon
(4) Video lasting time
(5) The video-loop time setting
(6) Video resolution
(7) Mobile detection is on
(8) GPS icon (no signal shows gray,
receives a signal shows green)
(9) Exposure compensation
(10) SD memory card
(11) Microphone
(12) System Date
(13) System Time
Video operations
Video settings
Press "MENU" button to get into video standby and settings.
[Video resolution] to set image resolution at: 1080P (1920x1080
30fps) /720P (1280x720 60fps) /720P (1280x720 30fps) /WVGA (848x480 60fps) /
VGA (640x480 60fps);
[Video cycle ] set cycle recording time: 1 minutes /2 minutes /3 minutes;
[WDR] set WDR state: on / off;
[Exposure compensation] set exposure compensation exposure value: -2.0, +2.0,
+5/3, +4/3, +1.0, +2/3, +1/3, +0.0, -1/3, -2/3, -1.0, -4/3, -5/3;
[Motion detection recording] set mobile detecting switch : on / off;
[Recording audio] set the recording audio: on / off;
[Date label] set the date and time: on / off;
While standby press " ", it will go to 9 grips status, press " " or " " to select file, and then
press " " to play. During playing press " " as fast forward (2×/×4/×8), press" " as
back forward (2×/×4/×8).
Video operation
9
Video playback File path Narrow window Full screen display
Close the program
Speed
Language selection
GPS map display
(make sure internet
is connected)
VIDEO RECORDING INSTRUCTIONS VIDEO PLAYER ON THE UNIT
SPECIFIED VIDEO PLAYER FOR PC
TROUBLESHOOTINGS