S.R.Smith SWIM-N-DUNK & COMMERCIAL BASKETBALL GAMES Instruction manual

SWIM-N-DUNK & COMMERCIAL
BASKETBALL GAMES
CORPORATE HEADQUARTERS
WESTERN SALES AND MANUFACTURING PLANT
P.O. Box 400 •
••
•1017 SW Berg Parkway
Canby, Oregon 97013
[phone] •
••
•[phone]
www.srsmith.com
06-647 S.R. SMITH, LLC 2004 JUN 09
ASSEMBLY AND INSTALLATION
INSTRUCTIONS

2
INTRODUCTION
The Commercial and Swim-N-Dunk Basketball Games are designed for use on in-ground pools in shallow
water depth areas. Proper and complete assembly, use and supervision is essential for proper operation
and to reduce the risk of accident or injury.
**IMPORTANT**
Check entire boxes and inside all packing materials for parts. Before beginning assembly, read the
instructions and identify parts using the figures and parts listed in this document. It is critical that all
parts be carefully inspected by the installer prior to installation to ensure that no damage occurred in
transit and that a damaged part is not used. Proper installation cannot be overstressed, as an improper
installation voids S.R. Smith’s warranty and may affect the safety of the user.
FIGURE 1
(3)
(14)
(1)
(13)
(11)
(20)
(16)
(5)
(15)
(4)
(8)
(7)
(2)
(17)
(10)
(12)
(11)
(6)

3
COMMERCIAL AND SWIM-N-DUNK PARTS LIST
NOTE: Two in-deck plastic anchors (AS-100P) for concrete decks are required to install the game.
ASSEMBLY INSTRUCTIONS
1. Begin by locating the basketball posts and the cross
brace as shown in FIGURE 1. This is simpler if the
vertical posts are already inserted in the anchors and
standing upright facing away from the pool. Attach the
cross brace to the posts with the stainless steel split tees
and hardware as shown in FIGURE 2.
2. Insert a 3/8” x 3.5” button head cap screw through
each hole drilled in the top of the backboard frame and
through a black flange bushing, as shown in FIGURE 3. A
7/32” allen wrench will be needed for tightening the button
head screws.
3. Attach the backboard to the posts by inserting
the 3.5” button head screws through the top holes of
the posts as shown in FIGURE 3 and fastening with
the 3/8” lock nuts. Do not completely tighten at this
time. Do not place the black nut caps over the lock
nuts until later in the assembly process, after all the
final tightening has occurred.
ITEM #
PART #
DESCRIPTION
QTY.
1 SPG-101 Basketball Rim & Net (Net alone SPG-106) 1 ea.
2 05-627 Flanged Bushing For 5/16" HDWR 4 ea.
3 05-628 Flanged Bushing For 3/8" HDWR 2 ea.
4 SPG-100 Basketball Backboard 1 ea.
5 20-110 or
20-132 Basketball Post Assembly Commercial Basketball Post Assembly 2 ea.
6 20-104 Basketball Post Cross Brace 1 ea.
7 2019061 Split Tee Half 4 ea.
8 2020049 3/8” x 2-1/2” Carriage Bolt 4 ea.
10 5-139 3/8” Hex Nut S/S 4 ea.
11 5-662 7/16” x 1” Flat Washer Stainless Steel 8 ea.
12 5-658 5/16” Hex Flange Nut Stainless Steel 4 ea.
13 5-656 5/16”-18 x 2” Hex Flange Bolt Stainless Steel 4 ea.
14 5-250 3/8” x 3.5” Button Head Cap Screw Stainless S. (7/32” Allen Wrench) 2 ea.
15 5-141 3/8” Nylon Lock Nut Stainless Steel 2 ea.
16 05-608 3/8” x 1” Nut Cap, Black 2 ea.
17 6-630 5/16” Dual Plastic Spacer 2 ea.
18 SPG-102 Basketball (not pictured) 1 ea.
19 SPG-103 Basketball Needle (not pictured) 1 ea.
20 05-32-111 3/8” Nylon Washer 4 ea.
FIGURE 2
FIGURE 3
(8) (7)
(10)
(7)
(3)
(15)
(16)

4
FIGURE 4
FIGURE 5
(20) (11)
(13)
(2)
(12) (11)
(17)

5
4. Attach the rim to the front of the backboard and to the post assembly on the opposite side of the
backboard with the 5/16” bolts, 1” OD flat washers, nylon washer, 3/8” flanged bushing and nuts as
shown in FIGURES 4 and 5. NOTE: Remove the protective film from the front face of the backboard
before mounting the rim. Make sure to place the 5/16” plastic spacers between the backboard frame and
the plate of the cross brace.
5. Fully tighten all hardware. Place the black nut caps over the 3/8” lock nuts.
6. Install the net to the rim. Refer to page 3 of the Huffy Sports Rim Owners Manual for the proper
installation procedures.
7. The Swim-N-Dunk and Commercial
Basketball units are to be anchored to the
deck using 6 inch deep AS-100P anchor
sockets. Install the anchors in the pool deck
17-1/2 inches apart on center and 12 inches
back from the pool’s edge for the Swim-N-
Dunk and 18 inches for the Commercial as
shown in FIGURE 5. Properly ground the
anchor sockets using the attached grounding
screw and the appropriate grounding wire per
local codes. Allow concrete to cure before
installing the Swim-N-Dunk or Commercial
Basketball unit.
8. Place the basketball assembly into the anchor sockets installed in the pool deck. Each anchor socket
has a removable cap, which needs to be removed before inserting the assembly. The cap can be
removed by inserting a small flat blade screwdriver into the groove between the anchor socket and the
cap and prying up. NOTE: When removing the basketball assembly from the anchors make sure to place
the caps in the anchors.
SAFETY INSTRUCTIONS
•This equipment is intended for use in shallow water depth areas.
•During play, do not wear jewelry (rings, watches, necklaces, etc.) Objects
may entangle in net.
•Do not dive or jump from any part of unit, including backboard support
braces or rim.
•Periodically inspect the rim, backboard and posts to assure there are no
worn parts and that all hardware is properly tightened.
FIGURE 5
FIGURE 5