Saab 32 025 907 User manual

900Installation instructions
SCdefault
MONTERINGSANVISNING ·INSTALLATION INSTRUCTIONS
MONTAGEANLEITUNG ·INSTRUCTIONS DE MONTAGE
SITdefault
Saab 9-3 4D/5D M03-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Saab 9-5 M01- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17
Handsfree kit, mobile phone
Accessories Part No. Group Date Instruction Part No. Replaces
32 025 907
32 026 144 9:89-31 May 07 32 025 872 Nov 06
F930A592

2 32025872
F930A488
1x 1x 1x
1x
1x
1x
11x

32025872 3
Saab 9-3 4D/5D M03-
Saab 9-3 4D/5D M03-
1 Ignition in OFF position.
2 Remove the floor console’s right-hand side
piece.
3 Remove the lower glove box screws.
4 Remove the inner glove box screws.
F930A491
3
F930A489
1
F930A490
2
C
A
B
B
F930A492
4

4 32025872
Saab 9-3 4D/5D M03-
5 Unplug the connector for the glove box lighting
(A).
Cars with ACC: Remove the coolant hose from
the glove box (B).
6 Remove the cover plate from the A-pillar trim.
7 Remove the retaining screw.
8 Grip the upper edge of the A-pillar trim and care-
fully pull out and up.
7
F930A495
F930A493
5
AB
F930A494
6
F930A496
8

32025872 5
Saab 9-3 4D/5D M03-
9 Remove the rear cover.
10 Remove the front cover.
11 Remove the screws.
12 Remove the centre cover.
F930A499
11
F930A497
9
F930A498
10
F930A500
12

6 32025872
Saab 9-3 4D/5D M03-
13 Cars with rain sensor: Remove the cover.
14 Fit the adhesive tape onto the microphone.
15 Fit the microphone.
16 Insert the microphone cable through the hole in
the headlining by the roof console.
F930A503
15
F930A501
13
F930A502
14
F930A504
16

32025872 7
Saab 9-3 4D/5D M03-
17 Route the microphone cable on under the head-
lining towards the windscreen. Press in the cen-
tre cover and draw the microphone cable tight at
the same time.
18 Route the microphone cable under the headlin-
ing.
19 Secure the microphone cable to the A-pillar.
20 Route the microphone cable under the panel,
and on to the centre console and secure it.
Important
Secure the wiring harness firmly so that there is no
risk of chafing and rattling.
F930A507
19
F930A505
17
F930A506
18
F930A508
20

8 32025872
Saab 9-3 4D/5D M03-
Fit the keypad in accordance with one of the alterna-
tives.
F930A509
22.1-22.5
21.1-21.7

32025872 9
Saab 9-3 4D/5D M03-
21 Fitting the keypad, alternative 1:
21.1 Remove the ashtray/storage compart-
ment.
21.2 Remove the ACC panel.
21.3 Fit the keypad to the console and mark out
the cable route.
21.4 Cut out from the console for the cable.
F930A513
21.3
F930A511
A
21.1
B
F930A512
B
A
21.2
F930A514
21.4

10 32025872
Saab 9-3 4D/5D M03-
21.5 Fit the keypad to the console.
21.6 Route the cable down behind the radio
down towards the air bellows and secure it.
21.7 Fit the ACC panel (A). Check that the key-
pad’s cable is located in the groove. Fit the
ashtray/storage compartment (B).
Important
Secure the wiring harness firmly so that there is no
risk of chafing and rattling.
F930A516
A
B
21.7
F930A515
21.5
F930A517
21.6

32025872 11
Saab 9-3 4D/5D M03-
22 Fitting the keypad, alternative 2:
22.1 Remove the cover.
22.2 Route the cable along the right-hand side,
down towards the air bellows.
22.3 Routethecableinthedashboard’sgroove.
22.4 Fit the cover.
F930A520
22.3
F930A518
A
B
22.1
F930A519
22.2
22.4
F930A521
A
B

12 32025872
Saab 9-3 4D/5D M03-
22.5 Fit the keypad and adjust any excess cable
length.
23 Connect the control module (A), microphone (B)
and keypad (C) to the adapter harness.
24 Secure the control module using two cable ties
to the panel member.
25 Release the Tele1 connection from the car’s
cable harness by cutting the tape. The Tele1
connection is located adjacent to the lower edge
of the centre console on the right-hand side.
F930A524
24
F930A522
22.5
F930A523
23
A B C
F930A525
25

32025872 13
Saab 9-3 4D/5D M03-
26 Connect the adapter harness to the car’s Tel 1
connection and secure the wiring.
27 Secure the wiring to the panel member.
28 Cars with rain sensor: Fit the cover.
29 Fit the screws to the cover.
Important
Secure the wiring harness firmly so that there is no
risk of chafing and rattling.
F930A527
26
F930A528
27
F930A529
28
F930A530
29

14 32025872
Saab 9-3 4D/5D M03-
30 Fit the front cover.
31 Fit the rear cover.
32 Align the A-pillar trim in position. Take care not
to damage the inflatable curtain.
33 Fit the retaining screw.
Tightening torque: 5 Nm (4 lbf ft).
WARNING
Take care not to damage the inflatable curtain.
Damage could result in the inflatable curtain not
providing the intended protection to the occupants
in the event of a collision.
F930A533
32
F930A531
30
F930A532
31
F930A534
5Nm
(4lbf ft)
33

32025872 15
Saab 9-3 4D/5D M03-
34 Fit the cover plate to the A-pillar trim.
35 Plug in the connector for the glove box lighting
(A).
Cars with ACC: Fit the coolant hose for the
glove box (B).
36 Fit the inner glove box screws.
37 Fit the lower glove box screws.
F930A537
36
F930A535
34
F930A536
35
AB
F930A538
37

16 32025872
Saab 9-3 4D/5D M03-
38 Fit the floor console’s right-hand side piece.
F930A539
38
A
C
B

32025872 17
Saab 9-5 M01-
Saab 9-5 M01-
1 Ignition in OFF position.
2 Remove the radio/navigation unit, M01-05:
2.1 Insert the special tools into the intended
holes until the tools engage and pull out
the unit.
2.2 Remove the compartment.
2.3 Unplug the connectors.
E930A429
M01-05
2.2
E930A427
1
E930A428
M01-05
2.1 A
B
CLICK
E930A430
M01-05
2.3

18 32025872
Saab 9-5 M01-
3 Remove the radio/navigation unit, M06-
3.1 Remove the plugs and remove the screws.
3.2 Pull the unit out and unplug the connectors
and disconnect the antenna connection.
4 Remove the ACC panel.
E930A433
4A
B
3.1
E930A431
M06-
E930A432
M06-
3.2

32025872 19
Saab 9-5 M01-
5 Remove the lower section of the dashboard on
the driver’s side:
5.1 Remove the data link connector (A)
5.2 Remove the lower panel (B).
5.3 Remove the clip (C).
5.4 Remove the floor lighting (D).
E930A434
C
B
B
A
D
B
5

20 32025872
Saab 9-5 M01-
6 Remove the cover to the fuses.
7 Remove the A-pillar trim (secured with clips).
Remove the upper clip (A) from the trim.
8 Remove the sun visor’s screws and allow the
sun visor to hang down.
9 Remove the glass cover (A), the retaining screw
(B) and lower the cover.
WARNING
Take care not to damage or loosen the energy
absorbers. Damaged or loosened energy absorb-
ers must not be refitted. In appropriate cases, the
whole of the headlining must be replaced. A dam-
aged energy absorber could provide reduced pro-
tection to the head in the event of impact.
E930A437
8
E930A435
6
E930A436
7A
E930A438
9
BA