SAFAVIEH COUTURE Caspian SFV4751-K User manual

CARE AND MAINTENANCE
NOTICE
2X
B Leg Part of Headboard(L&R) 2X
2X
C Footboard 1X
Part List and Hardware List
PIECE DESCRIPTION PICTURE
QUANTITY
SAFAVIEH
1X
2X
AHeadboard 1X
Spot clean using a mild water-free solvent. Only a professional cleaner should
undertake a complete overall cleaning.
The use of steam or water-based cleaners may cause excessive shrinking or
staining.
* Please make sure that you have all parts indicated before you begin assembly of
this item
* This item should be assembled on a soft surface to prevent scratching the finish
during assembly
* This item may require periodic tightening
Dimensions: 81.1"WX85.4"DX65.4"H
Weight Capacity: 825 lbs
C O U T U R E
Leg Part of Footboard(L&R)
H Support Leg for Cross Slat 4X
Cross Slat
WARNING: DO NOT STAND ON BED
WARNING: DO NOT OVER TORQUE BOLTS/SCREWS
SFV4751-K
HW6
1X
Slat
D
E
F
G
HW1
HW2
HW5 Allen Key
Phillips Screws 4*2*40MM
1X
Wrench
10X
10X
Split Lock Washer(M8)
Flat Washer(M8)
Socket Screws 8*1.25*40MM
HW3
HW4
12X
10X
Sideboard(L&R)
The legs and hardware are located inside the sideboard&slat boxs.

PREPARATION
The legs and hardware are located inside the sideboard&slat boxs.
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
If any partismissing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 15minutes.
Tools Required for Assembly (included): Allen key/wrench
PREARATION
STEP1 Open the velcro on the headboard A, attach the
leg part of headboard B to the headboard A by using
allen key HW5 and hardware HW2, HW3, HW4 as
shown, tighten until secure, Then smooth the velcro.
STEP4 Rotate the slat legs H to the middle rod of slat
G. Put it inside the middle of the bed, And then,
smooth the slat F inside the bed
HW1
Assembl the slat legs"H" with part ofAssembl the slat legs"H" with part ofAssembl the slat legs"H" with part of Assembl the slat legs"H" with part of
STEP5 Secure the slat with screw HW1 by using
wrench HW6.There are totally 12 holes on slat to
make sure it stable, it's shown in step 4
HW5
HW2
HW3
HW4
STEP2 Open the velcro on the footboard C, attach the leg
parts of footboard D to the footboard C by using allen key
HW5 and hardware HW2,HW3,HW4 as shown, tighten until
secure. Then smooth the velcro.
HW5
HW2
HW3
HW4
STEP3 Attach the sideboard E with headboard(Step1)
and footboard(Step2) by sliding the iron plates onto the
Bolts,The metal card should be alignment card
slot when install it,then press it lightly.
G
H
HW6
It's finished as shown,Your Bed is
ready for use.
HW6
X2
F
B/L B/R
AC
D/L D/R
E/L
E/R

CARE AND MAINTENANCE
NOTICE
2X
B Leg Part of Headboard(L&R) 2X
2X
C Footboard 1X
Part List and Hardware List
PIECE DESCRIPTION PICTURE
QUANTITY
SAFAVIEH
1X
1X
AHeadboard 1X
Spot clean using a mild water-free solvent. Only a professional cleaner should
undertake a complete overall cleaning.
The use of steam or water-based cleaners may cause excessive shrinking or
staining.
* Please make sure that you have all parts indicated before you begin assembly of
this item
* This item should be assembled on a soft surface to prevent scratching the finish
during assembly
* This item may require periodic tightening
Dimensions:65.4"WX85.4"DX65.4 "H
Weight Capacity: 825 lbs
C O U T U R E
Leg Part of Footboard(L&R)
H Support Leg for Cross Slat 2X
Cross Slat
WARNING: DO NOT STAND ON BED
WARNING: DO NOT OVER TORQUE BOLTS/SCREWS
SFV4751-Q
HW6
1X
Slat
D
E
F
G
HW1
HW2
HW5 Allen Key
Phillips Screws 4*2*40MM
1X
Wrench
10X
10X
Split Lock Washer(M8)
Flat Washer(M8)
Socket Screws 8*1.25*40MM
HW3
HW4
9X
10X
Sideboard(L&R)
The legs and hardware are located inside the sideboard&slat boxs.

PREPARATION
The legs and hardware are located inside the sideboard&slat boxs.
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
If any partismissing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 15minutes.
Tools Required for Assembly (included): Allen key/wrench
PREARATION
STEP1 Open the velcro on the headboard A, attach
the leg part of headboard B to the headboard A by
using allen key HW5 and hardware HW2, HW3, HW4
as shown, tighten until secure, Then smooth the
velcro.
STEP4 Rotate the slat legs H to the middle rod of slat
G. Put it inside the middle of the bed, And then,
smooth the slat F inside the bed
HW1
Assembl the slat legs"H" with part ofAssembl the slat legs"H" with part ofAssembl the slat legs"H" with part of Assembl the slat legs"H" with part of
STEP5 Secure the slat with screw HW1 by using
wrench HW6.There are totally 9 holes on slat to make
sure it stable, it's shown in step 4
HW5
HW2
HW3
HW4
STEP2 Open the velcro on the footboard C, attach the leg
parts of footboard D to the footboard C by using allen key
HW5 and hardware HW2,HW3,HW4 as shown, tighten until
secure. Then smooth the velcro.
HW5
HW2
HW3
HW4
STEP3 Attach the sideboard E with headboard(Step1)
and footboard(Step2) by sliding the iron plates onto the
Bolts,The metal card should be alignment card
slot when install it,then press it lightly.
G
H
F
HW6
It's finished as shown,Your Bed is
ready for use.
HW6
B/L B/R
AC
D/L D/R
E/L
E/R