Safco 7751 User manual

MODEL
NUMBER 7751
7751-37: 1 of 2; 05/99
One Tier Sorter Module
For questions or concerns, please call
Safco Consumer Hot Line 1-800-664-0042
available Monday-Friday 8:00 AM to 4:30 PM (Central Time)
(English-speaking operators)
ASSEMBLY INSTRUCTIONS
Safco Products Company, New Hope, MN 55428
Back Panel 1 7751-01
Right Side Panel 1 7751-04
Left Side Panel 1 7751-03
Bottom Shelf 1 7751-02
Dividers 6 7751-06
Top Shelf 1 7751-05
Mail Trays 20 7751-07
Label Holders 25 7751-08
Label Sheet (not shown) 1 7751-35
Q
Q
Q
Q
Q
Q
Q
Q
Q
LETTER
CODE DESCRIPTION QTY. PART NO.
PARTS LIST
Sort and count your parts!
A
B
C
D
E
F
G
H
I
This product will assemble very easily IF you read and follow the instructions carefully.
So take your time, read your instructions, and enjoy your project.
IMPORTANT READ and FOLLOW these instructions carefully!
CHECK ALL PACKAGING - there may be parts in it!
SORT and COUNT your parts - compare with the list below. If you find problems,
refer to the Product Warranty Registration form included with this product.
2
1
ASSEMBLED UNIT
Position A Back Panel with the inner rails
facing you. Position the B Right Side Panel
with the tabs to the back and the flange side
facing to the left. Insert the tabs on the right
side panel into the tab slots on the back panel
from the BACK side (see Inset A). Repeat for
the C Left Side Panel.
3
QQ
QQ
Q
G
QQ
QQ
Q
E
QQ
QQ
Q
F
QQ
QQ
Q
B
QQ
QQ
Q
C
QQ
QQ
Q
D
QQ
QQ
Q
H
QQ
QQ
Q
A
INNER RAIL QQ
QQ
Q
B
QQ
QQ
Q
TAB &
TAB SLOT
QQ
QQ
Q
QQ
QQ
Q
QQ
QQ
Q
A
Inset A

7751-37: 2 of 2; 05/99 Safco Products Company, New Hope, MN 55428
Insert one E Divider (with narrow tabs to bottom and
holes closest to long sides toward the back) behind the
turned-in flange on the right side panel. Slide
divider down into the slots near the right edge
of the bottom shelf. Repeat for left side.
5
Slide the D Bottom Shelf into position as shown
with the recessed side
facing down. Be sure the
end flanges on the
bottom shelf are INSIDE
the lower flanges on the
side panels and the
front edge of the bottom
shelf is UNDER the
turned-in flanges on the
FRONT of the side
panels (Inset B).
4
Repeat Step 6 to work your way left across the entire
length of the bottom shelf until all dividers are in place.
7
Gently press the side tabs inward to slide the G Mail
Trays in (recessed area facing down and indented finger
cutouts facing front). Let tabs slide into holes on the
dividers. Holes are offset so trays can be placed next to
each other horizontally. To move the trays, gently push
the side tabs out of the holes from below and tilt or
slide into new position.
8Attach the H Label Holders to the front of the mail
trays. Insert the long flange of the label holder under
the lip of the mail tray and
gently roll it up over the
tray lip (Inset D).
9
TURNED-IN FLANGE
QQ
QQ
Q
D
QQ
QQ
Q
Inset B
QQ
QQ
Q
LOWER FLANGE
TURNED-IN
FLANGE
NARROW TABS
SLOTS
Place one end of the F Top Shelf into
the right side panel. With a helper
holding one end up, insert narrow tabs of
another E Divider into the next set of
slots from the right. Carefully lower top a
little more to catch the upper tabs on the
divider. Be sure to insert FLANGE on
back of top shelf into INNER RAILS on
back panel (Inset C).
6QQ
QQ
Q
QQ
QQ
Q
INNER RAILS
MAIL
TRAY
LONG
FLANGE
Inset D
FINGER
CUTOUT
SIDE
TABS
QQ
QQ
Q
QQ
QQ
Q
FLANGE
Inset C
QQ
QQ
Q
E
QQ
QQ
Q
F
QQ
QQ
Q
G
QQ
QQ
Q
H
FRONT
RIGHT SIDE PANEL
QQ
QQ
Q
E
NARROW TABS
INNER
RAIL
Firmly grasp the bottom of the unit (with a helper)
and carefully lift the assembled Riser into place.
NOTE: Lift from the bottom only.
TO FRONT
NOTE: Holes closest to
long edge to back of unit.