Safeline CONNECTable User manual

www.safeline-group.com
11. 2018 © 2018 SafeLine and all the SafeLine products and
accessories are copyrighted by law.
CONNECTable
Manual
Conguration & Monitoring
CONNECTable v.2.01 EN

2
CONNECTable v.2.01 EN
Introduction
Introduction
General information 3
Overview 4
Requirements 4
Installation
Connection 5
Disconnecting 6
Troubleshooting 6
Replacing the battery 6
Replacing the cable 6
Certication
Declaration of Conformity 7
Content

3
CONNECTable v.2.01 EN
Introduction
This unit was built with state-of-the-art technology and to
generally recognised safety related technical standards currently app-
licable. These installation instructions are to be followed by all people
working with the unit, in both installation and maintenance.
It is extremely important that these installation instructions are made
available at all times to the relevant technicians, engineers or servicing
and maintenance personnel. The basis prerequisite for safe handling
and trouble free operation of this system is a sound knowledge of the
basic and special safety regulations concerning conveyor technology,
and elevators in particular. The unit may only be used for its intended
purpose. Note in particular that, no unauthorised changes or additions
may be made inside the unit or individual components.
Exclusion of liability
The manufacturer is not liable with respect to the buyer of this product
or to third parties for damage, loss, costs or work incurred as a result of
accidents, misuse of the product, incorrect installation or illegal chang-
es, repairs or additions. Claims under warranty are likewise excluded in
such cases. The technical data is the latest available. The manufacturer
accepts no liability arising from printing errors, mistakes or changes.
Declaration of conformity
Download ”The declaration of conformity” at our website:
www.safeline-group.com
Safety Precautions!
- Only trained professionals, who are authorised to work on the equip-
ment, should install and con gure this produc t.
- This quality product is dedicated for the lift industry. It has been
designed and manufactured to be used for its speci ed purpose only.
If it is to be used for any other purpose, SafeLine must be contacted in
advance.
- It should not be modi ed or altered in any way, and should only be
installed and con gured strictly following the procedures described in
this manual.
- All applicable health and safety requirements and equipment
standards should be considered and strictly adhered to when installing
and con guring this product.
- After installation and con guration this product and the operation
of the equipment should be fully tested to ensure correct operation
before the equipment is returned to normal use.
Electrical and electronic products may contain materials, parts and
units that can be dangerous for the environment and human health.
Please inform yourself about the local rules and disposal collection
system for electrical and electronic products. The correct disposal of
your old product will help to prevent negative consequences for the
environment and human health.
General
information

4
CONNECTable v.2.01 EN
Introduction
Overview RS232 connection
Connection to plug into one
of SafeLines lift emergency
telephones.
LED
LED indicator.
CONNECTable can be used with the following SafeLine telephones:
SafeLine MX3
SafeLine MX2
SafeLine SL6
SafeLine SL2
SafeLine SL1
SafeLine TTR
SafeLine 3000
In order to use the SafeLine CONNECT app, the following is required:
• iPhone 4S (or newer) with iOS 8 or later.
• Android smartphone with Android 4.3 (Jelly Bean) or later and BLE 4.0
App Store for iPhone Google play for Android
Button
Button that connects to/
disconnects from the
emergency telephone.
Requirements

5
MX2
MX3
SL1
SL6
SL2
TTR
SL3000
MX2
MX3
SL1
SL6
SL2
TTR
SL3000
MX2
MX3
SL1
SL6
SL2
TTR
SL3000
CONNECTable v.2.01 EN
Installation
Connection Step 1
Connect CONNECTable to the lift emergency telephone via the
RS232 connector.
Step 2
Press and hold the CONNECTable button for at least one (1) second,
until the LED starts ashing.
Step 3
When the LED is ashing, open the smartphone/tablet
app. The app will show all CONNECT units within reach.
Select the correct unit and follow the instructions in the
app to congure the emergency telephone.

6
CONNECTable v.2.01 EN
Installation
Disconnecting Disconnect the CONNECTable from the emergency telephone by either:
• pressing “Disconnect” in the app, or
• pushing the button on the CONNECTable once, and wait until
the LED turns off.
When the LED turns off, CONNECTable can safely be disconnected
from the emergency telephone.
WARNING!
CONNECTable must be turned
off before disconnecting it from
the hardware.
Troubleshooting If there is a problem, in the rst instance, always try one of the
following:
• Connect CONNECTable again by following the connection
instructions, step 1-3. When connected, adjustments that might
have been made in the conguration settings will have been saved.
• Disconnect the power from the SafeLine telephone and make
sure that it is turned off. Reconnect the power. Adjustments that
might have been made in the conguraton settings will be lost.
• Make sure that the emergency telephone supports
CONNECTable.
Replacing the
battery
To replace the battery, open the enclosure and remove the battery.
Replace it with a new CR2032 battery (Art.No: *BATT-CR2032).
Replacing the
cable
To replace the cable, open the enclosure and unplug the faulty cable.
Remove it, and replace it with a new CONNECTable cable (Art.No:
*CABLE17).

Your partner in lift safety
Antennvägen 10, 13548 Tyresö, Sweden
[phone], www.safeline-group.com
EU Declaration of Conformity
Product: Wireless programing device / Dongle
Type / model: SafeLine CONNECTable
Article no: *CONNECTABLE
Manufacturer: SafeLine Sweden AB
Year: 2017
We herewith declare under our sole responsibility as manufacturer that the products referred to
above complies with the following EC Directives:
Directives
Radio Equipment (RED): 2014/53/EU
RoHS 2: 2011/65/EU
Standards applied
EN 62368–1:2014/AC:2015 LVD: Information Technology Equipment
EN 50581:2012 RoHS: Technical doc. for assessment of restriction of RoHS.
For RED 2014/53/EU, the conformity assessment procedure “Module A” used as described in Annex II. Accordingly, respective
manufacturer has done the radio modules conformity assessment:
Standards applied Article of Directive 2014/53/EU
EN 60950-1:2006+A11:2009+A1:2010+A12:2011 3.1 (a): Health and safety of the user
EN 62311:2008
EN 301 489-1 v2.1.1 + EN 301 489-52v1.1.0 Draft 3.1 (B): Electromagnetic Compatibility
EN 301 489-17 V3.1.1
EN 300 328 V2.1.1 3.2: Effective use of spectrum allocated
Firmware used during assessment
SafeLine CONNECTable: 1.00
Tyresö, 2017-04-07
Lars Gustafsson,
Technical Manager, R&D , SafeLine Group
Module
Notified body
Address
NB nr
Test nr
CYW20732S
NTS Silicon Valley
41039 Boyce Road, Fremont, CA 94538, US
0214.26
R 104750/51

www.safeline-group.com www.safeline-group.com
SafeLine Europe
Industrieterrein 1-8 · 3290 Diest · Belgium
Tel.: [phone] · [email protected]
Support: [phone]
SafeLine Deutschland GmbH
Kurzgewannstraße 3 · D-68526 Ladenburg · Germany
Tel.: [phone] · [email protected]
SafeLine Norway
Solbråveien 49 · 1383 Asker · Norway
Tel.: [phone] · [email protected]
SafeLine Denmark
Erhvervsvej 19 · 2600 Glostrup · Denmark
Tel.: [phone] · [email protected]
SafeLine Headquarters
Antennvägen 10 · 135 48 Tyresö · Sweden
Tel.: [phone] · [email protected]
Support: [phone]
SafeLine Group UK
Unit 47 · Acorn Industrial Park · Crayford ·
Kent · DA1 4AL · United Kingdom
[e-mail]