Safety Technology International STI Wireless Driveway Monitor STI-V34150 User manual

Installation and Operation Manual
STI Wireless Driveway MonitorTM
Part of the Wireless Alert Series
Thank you for purchasing the STI Wireless Driveway Monitor. Your satisfaction is very important to us.
Please take the time to read this manual carefully to get the most from your new product.
How the product works
Because of its patented magnetometer sensor transmitter system, the Driveway Monitor will only be
triggered by cars or trucks - not people, animals and so forth. When a vehicle passes the Motion
Alert®Sensor Transmitter next to the driveway, the receiver unit inside the office or home sounds a
programmable message. The earth has a uniform magnetic field around it. A vehicle creates a slight
disturbance in the earth’s field. The sensor transmitter detects this disturbance and transmits a signal
to the receiver.
Before you start
Refer to this drawing to become familiar with all the parts.
BATTERY POWERED SENSOR
TRANSMITTER
SOLAR POWERED SENSOR
TRANSMITTER
Models: STI-V34150 - Battery Power Kit
STI-V34100 - Solar Power Kit
STI-34151 - Battery Powered Sensor
STI-34101 - Solar Power Sensor
SENSOR
TRANSMITTER
CAP
SENSOR
TRANSMITTER
BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12” MOUNTING TUBE
MOUNTING STAKE
SENSOR
TRANSMITTER
BOTTOM
SENSOR
TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM SCREWS
RECHARGEABLE AA
NiMH BATTERIES
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
+
+
-
B
-
SENSITIVITY
ADJUSTMENT
12” MOUNTING TUBE
PLASTIC FILM
REMOVE BEFORE USE

— 2 —
Install batteries into the sensor transmitter
1. Remove the sensor transmitter cap by turning it counterclockwise.
2. WITHOUT PULLING ON THE BRASS ANTENNA OR ANY WIRES, grasp the outside
of the battery/circuit board holder by the finger notches, twist gently and pull out.
Insert two “C” alkaline batteries (not included).
3. Replace the battery holder/sensor transmitter and sensor transmitter cap.
4. To test or program sensor transmitter, place the sensor transmitter on a table or
counter approximately 5-10 ft. away from the receiver. Sensor transmitter can be
activated by rotating and will make a faint clicking noise to verify operation.
5. Sensor should be programmed to receiver before mounting outdoors. Refer to
receiver instructions for programming.
Battery Powered (STI-V34150 & STI-34151)
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
HL
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H
L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
HL
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
REMOVE PLASTIC FILM
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
HL
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H
L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
HL
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
REMOVE PLASTIC FILM
Sensitivity Adjustment
The factory default setting (HIGH) may be adjusted by changing the jumper position inside the
sensor transmitter.
1. Unscrew cap.
2. Position the jumper to desired sensitivity (as shown).
 •LOW:Positionjumperonthetwobottompegs.
 •MEDIUM:Completelyremovejumperorhangonmiddlepeg.
 •HIGH:Positionjumperonthetwotoppegs.
3. Replace cap.
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
HL
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H
L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
HL
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
REMOVE PLASTIC FILM
Low Sensitivity Setting:
•
•
•
Jumper Location
Medium Sensitivity Setting:
•
•
•
Jumper Location
High Sensitivity Setting:
•
•
•
Jumper Location
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
HL
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H
L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
HL
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
REMOVE PLASTIC FILM
Sensitivity Adjustment
The factory default setting (HIGH) may be adjusted by changing the jumper position inside
the sensor transmitter.
1. Remove the bottom of the sensor transmitter by removing the 3 screws on the bottom
of the unit.
2. Position the jumper to desired sensitivity (as shown below).
 •LOW:Positionjumperonthetwoleftmostpegs.
 •MEDIUM:Completelyremovejumperorhangfrommiddlepeg.
 •HIGH:Positionjumperonthetworightmostpegs.
3. Replace the bottom of the unit and secure with the 3 screws.
Solar Powered (STI-V34100 & STI-34101)
1. Remove plastic film on solar panel.
2. Remove the bottom of the sensor transmitter by removing the 3 screws on the
bottom of the unit.
3. Remove the plastic tab between the batteries.
4. Replace the bottom of the unit and secure with the 3 screws. Place the sensor
transmitter in direct sunlight for 48 hours.
OR
5. Place batteries in a NiMH (nickel metal hydride) battery charger (before using). Once charged, return the batteries to the
sensor transmitter. Replace the bottom and secure with the 3 screws.
6. To test or program sensor transmitter, place the sensor transmitter on a table or counter approximately 5-10 ft. away from
the receiver. Sensor can be activated by rotating. Sensor transmitter can be activated by rotating and will make a faint
clicking noise to verify operation.
7. Sensor should be programmed to receiver before mounting outdoors. Refer to receiver instructions for programming.
Low Sensitivity Setting:
• • •
Jumper Location
Medium Sensitivity Setting:
Jumper Location
High Sensitivity Setting:
Jumper Location
• • • • • •
SENSOR
TRANSMITTER
CAP
SENSOR
TRANSMITTER
BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12” MOUNTING TUBE
MOUNTING STAKE
SENSOR
TRANSMITTER
BOTTOM
SENSOR
TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM SCREWS
RECHARGEABLE AA
NiMH BATTERIES
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
+
+
-
B
-
SENSITIVITY
ADJUSTMENT
12” MOUNTING TUBE
PLASTIC FILM
REMOVE BEFORE USE

Installation Instructions
The Solar Sensor Transmitter must be placed in an area that receives partial or full sunlight. For both models, be sure the
location of the sensor transmitter is at least 25’ back from the main road. For a typical 12’ wide driveway, it is recommended
the sensor transmitter be no more than 3’ away from the driveway (see drawing). Additional sensor transmitters may be required
for driveways exceeding 12’. Sensor transmitter may be placed up to 1,000 feet away from receiver; however, range may vary
depending upon environment and use of wireless telephones, wireless routers and other similar devices.
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
HL
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H
L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
HL
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
REMOVE PLASTIC FILM
STI-30104
LAMP CONTROLLER
(OPTIONAL)
AC ADAPTER
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
STI-34104
INDOOR RECEIVER
BUTTON
RED LED
SENSOR TRANSMITTER CAP
SENSOR TRANSMITTER BASE
MOUNTING
TUBE CAP
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
2 “C” BATTERIES
(NOT INCLUDED)
SENSOR TRANSMITTER
12”MOUNTING TUBE
MOUNTING STAKE
SENSOR TRANSMITTER
BOTTOM
SENSOR TRANSMITTER
MOUNTING
TUBE CAP
MOUNTING STAKE
SENSOR TRANSMITTER BOTTOM
SCREWS
RECHARGEABLE NiMH BATTERIES
HL
SENSITIVITY JUMPERS
(SOLAR TYPE)
SENSITIVITY JUMPERS
(BATTERY TYPE)
H
L
FINGER
NOTCHES
REMOVE PLASTIC TAB
FROM BATTERIES
DRIVEWAY
3’OR
LESS
25' OR MORE
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25'
OR MORE FROM STREET.
12’
MAX
DRIVEWAY
PLACE SENSOR
TRANSMITTER 3' OR
LESS FROM EDGE OF
DRIVEWAY AND 25+
FEET OR MORE FROM
STREET.
25' OR MORE
3' OR
LESS
12'
MAX
+
+
-
B
DETAIL B
SCALE 2:1
B
C
HL
-
+
+
-
B
-
FINGER NOTCHES
DO NOT
PULL ANTENNA!
WALL MOUNT (INCLUDED)
NOT NEEDED FOR POLE
MOUNT INSTALLATION
SENSITIVITY
ADJUSTMENT
SENSITIVITY
ADJUSTMENT
POWER CONNECTOR ANTENNA CONNECTOR
12”MOUNTING TUBE
GREEN
LED
TRANSISTOR
OUTPUT JACK
RECEIVER ANTENNA
SPEAKER
BUTTON
RED LED
POWER CONNECTOR ANTENNA CONNECTOR
REMOVE PLASTIC FILM
1. Place cap on tube.
2. Insert stake to opposite end of tube.
3. Place the tube (stake side down) into the ground within 3’ of the driveway
and more than 25’ from the road.
4. Gently hammer the cap side of the tube until stake is firmly in the ground.
5. Remove cap and place sensor transmitter on tube.
6. The sensor transmitter should have a clear line-of-site to the receiver to
improve performance.
7. Place the sensor transmitter so the vehicle does not pass between it and
the receiver.
To obtain optimal range
STI recommends the use of the stake and tube included with your Driveway
Monitor. However, if you choose to mount the unit to an alternate mounting
device, please be sure the device is stable. STI does not recommend
mounting the sensor transmitter to a tree or a metal fence or gate.
TROUBLE SOLUTION
1. Check that the receiver is not in Temporary or Permanent Silent Mode (red LED solid).
2. Check the sensor transmitter by picking it up and rotating it. The sensor transmitter should make
a “faint clicking” noise.
3. Check that the sensor transmitter and receiver are within operating distance from each other.
4. Check the sensor transmitter batteries and replace if necessary.
5. Reprogram the receiver using the steps in “Clearing the receiver memory” and “Program a device
into the receiver.”
The RECEIVER does
not sound when a
vehicle passes.
1. Check that the sensor transmitter and receiver are within operating distance from each other.
2. Change the Sensitivity in the sensor transmitter using the steps in “Sensitivity Adjustment.”
3. Check that the sensor transmitter and receiver are located so a vehicle does not pass
between them.
4. Change the location of the sensor transmitter by placing it closer to the edge of the driveway.
5. Bring the sensor transmitter close enough to the receiver so the receiver button can be heard.
Test the sensor transmitter by passing a steel shovel or large magnet around the sensor
transmitter. The sensor transmitter should make a “faint clicking” noise and the receiver
should sound.
6. Check the sensor transmitter batteries and replace if necessary. On the solar powered
driveway monitor, make sure the sensor transmitter is in direct sunlight and has been charged
in direct sunlight for at least 48 hours after replacing batteries. Use only AA (1.2v) NiMH
rechargeable batteries.
7. Reprogram the receiver using the STI-V34104 install.
The SENSOR
TRANSMITTER does
not activate when a
car passes.
1. Sensor transmitter mounted firmly and not effected by wind?
2. Sensor transmitter at least 25’ away from the main road?
3. Be sure there are no other metal objects near the sensor transmitter that may move.
4. Reprogram the receiver using the STI-V34104 install.
The RECEIVER sounds
when there is no
vehicle passing.
Call STI Technical Support at 800-888-4784
Still having problems
— 3 —

Important notice
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning
theequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:
 •Reorientorrelocatethereceivingantenna
 •Increasetheseparationbetweentheequipmentordevices
 •Connecttheequipmenttoanoutletotherthanthereceiver’s
 •Consultadealeroranexperiencedradio/TVtechnicianforassistance
Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseinterference,and(2)thisdevicemustaccept
any interference, including interference that may cause undesired operation of the device. Changes or modifications not expressly
approved by Safety Technology International, Inc. could void your authority to operate this equipment.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.
Warranty information
Safety Technology International, Inc. warrants to the original consumer/purchaser that this product shall be free of defects in
material and workmanship under normal use and circumstances for a period of one (1) year from the original date of purchase.
Electronic warranty form at www.sti-usa.com/wc14.
Model 34101 Model 34151
 FCCID:TXL34101 FCCID:TXL34151
 IC:6335A-34101 IC:6335A-34151
Inst. Sht. WirelessDriveway Aug 2019
Additional Wireless Alert Series Products
STI-34098 Single Channel Slave Receiver
STI-V34104 4-Channel Voice Receiver
STI-34108 8-Channel Receiver
STI-34101 Solar Powered Driveway Monitor Sensor
STI-34151 Battery Powered Driveway Monitor Sensor
STI-34201 Wireless Mail Alert Sensor
STI-34301 Wireless Garage Sentry Sensor
STI-34401 Wireless Universal Alert Sensor
STI-34501 Wireless Door Entry Alert®Sensor
STI-34601 Wireless Doorbell Button
STI-34701 Indoor Wireless PIR
STI-34752 Outdoor Wireless PIR
STI-6200WIR Wireless Fire Extinguisher Theft Stopper®
STI-6400WIR Wireless Exit Stopper Door Alarm
STI-6517A WIreless Stopper®Station Shield with Sound
STI-6517B Wireless Stopper®Station Shield with Sound
and Transmitter
STI-6517C Wireless Stopper®Station Shield with
Wireless Button
STI-6517D Wireless Stopper®Station Shield with Button
Sound and Transmitter
STI-30105 Extended Antenna
STI-30106 Mounting Replacement Kit (includes cap,
wall mount, tube and stake)
STI-34105 Voltamax 12VDC (500mA) Power Supply
STI-34106 Keyfob
STI-34188 8-Zone Relay Board
2306 Airport Rd • Waterford, MI 48327, USA
Phone: [phone] • Fax: [phone]
[email protected] • www.sti-usa.com
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England • Tel: [phone]
Fax: [phone] • [email protected] • www.sti-emea.com