Sage Milk Cafe BMF600 User manual

the Milk Café™
BMF600
EN QUICK GUIDE DE KURZANLEITUNG

6
KNOW YOUR SAGE®MILK CAFÉ™
A
B
H
J
I
C
D
E
F
G
A. Measuring Cap
B. Jug Lid
C. Dishwasher Safe Milk Jug
D. Power Base
E. START | STOP Push-Dial
F. LED Indicator
G. Cord Wrap
H. ‘On Board’ Disc Storage
I. ‘Cappuccino’ Frothing Disc
J. ‘Latte’ Frothing Disc
Rating Information
220-240V ~50–60Hz 500W

7
OPERATING YOUR SAGE®MILK CAFÉ™
FROTHING HOT MILK
1. Placethemilkfrotheronaatlevelsurface
and plug the power cord into a 220–240V
power outlet.The START | STOP button
surround will illuminate.
2. Select the ‘Capp’ or ‘Latté’ frothing disc.
Choose the ‘Capp’ disc for thick and
creamy froth or the ‘Latté’ disc for smooth
and silky milk.
3. Insert the frothing disc onto the shaft at
the base of the milk jug. Ensure the disc
is inserted the correct way with the
wider part of the disc at the bottom
of the jug. The disc should ‘click’ securely
onto the shaft.
NOTE
If the disc is not inserted correctly it may
dislodge during operation, a grinding noise
may be heard, or milk will not swirl.
WARNING
Frothing disc is a choking
hazard. Children must always
be supervised and never left
unattended with the appliance.
4. Pour the required amount of cold, fresh (or
freshlyopened)milkintothemilkjugthen
cover with the jug lid.
NOTE
Never operate without the minimum level
of liquid in the milk jug.The milk frother
willautomaticallyturnoifthemilkjugis
empty. If this occurs, you will need to wait
for the milk frother to cool down before re-
use, refer to page 8.
5. Ensure the jug lid is securely attached. Place
the milk jug onto the power base.
6. Turn the START / STOP push-dial to the
desired temperature.
7. Only press the START / STOP push-dial
once,rmly.Frothing has started once the
milk frother beeps once and the button
surround slowly ashes.
NOTE
Do not remove the milk jug from the power
base during operation. Doing so may
dislodge the frothing disc and cause a
grinding noise. Always press the centre of the
START / STOP push-dial before removing the
jug. Operation has stopped once the button
surroundhasstoppedashing.

8
WARNING
Appliance surfaces will be hot
during and after operation.
8. Clean the milk jug and frothing disc
immediately after use. Refer to Care
& Cleaning.
NOTE
When frothing multiple batches, to prevent
the Boil Dry Protection from activating, we
recommend allowing the milk jug to cool
forapproximately5minutes,orllingthe
milk jug with water for faster cooling.
USING THE ‘COLD STIR’ SETTING
The ‘Cold Stir’ setting allows you to stir already
cold or hot milk without additional heat.
Use it to froth milk for cold beverages such as
an iced cappuccino; to blend in syrups and
avouringsforanicedchocolateormocha;
or to stir in dissolvable instant drinking powders
into milk or water.
NOTE
The milk frother has been designed
specicallyforthepurposeoffoamingmilk
and other dairy milk alternatives and is
not intended to whip, thicken or heat other
food substances eg. oil, eggs, butter, heavy
whipping cream, soups, gravies etc.
The milk frother is not designed to mix a
large quantity of dry ingredients or melt large
food pieces eg. cubed chocolate, ground
nuts, whole spices, fresh herbs or ice cubes.
ADDING INGREDIENTS
Always allow the milk frother to start for
a few seconds before using the measuring
cap to gradually add ingredients.
Always add ingredients slowly and in small
quantities.
NOTE
Frothingresultsdierdependingonthe
ingredients used. For example, adding
dense ingredients like thick syrups, heavy
powdersandlargeakescansignicantly
reduce the amount of foam.
SAFETY FEATURES
Boil Dry, Overheating Protection
The milk frother will automatically cease to
operate if the milk jug overheats.This can
be caused if the milk jug is empty, if liquid is
below the MIN measurement marking, or after
consecutive uses. If this occurs, 3 alerts will
sound. Unplug the power cord from the power
outlet, wait approximately 5 minutes for the milk
frothertocooldownorllthemilkjugwithwater
for faster cooling.
Thermal Fuse & Current Protection
This feature protects the milk frother in case
of major fault. If this occurs, the milk frother
willautomaticallyturnoandwillnotreactivate.
Immediately cease use, remove the power
plug from the power outlet and visit
www.sageappliances.com or call
Sage Consumer Service.
OPERATING YOUR SAGE®MILK CAFÉ™

9
CARE & CLEANING FOR YOUR SAGE®MILK CAFÉ™
Both the milk jug and frothing disc should be
cleaned immediately after each use to prevent
build-up of milk residue.
1. Unplug the power cord from the power outlet
before cleaning.
2. The milk jug and frothing disc will be hot
immediately after use, so carefully remove
themilkjugfromthepowerbaseandllwith
tap water. Once the milk jug and frothing disc
have cooled completely, remove the frothing
discandrinseoanymilkinwarmwater.
3. Wash the milk jug, jug lid, measuring cap
and frothing disc in warm soapy water, rinse
and dry thoroughly.
The seal from the lid can be removed and
washed separately.
4. Wipe the exterior of the power base with
a soft damp cloth. Dry thoroughly.
NOTE
Do not use alkaline or abrasive cleaning
agents, steel wool or scouring pads on any
part of the milk frother as these can damage
the appliance surfaces.
NOTE
Never immerse the power base in water
or any other liquid.The outside of the milk
jug must always be clean and dry before
placing on the power base prior to use.
NOTE
The milk jug, jug lid, measuring cap and
frothing discs can be washed in
thedishwasher(topshelfonly).However
to extend the life of the frothing discs, we
recommend these are washed by hand.

10
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE WHAT TO DO
Milk is not
foaming?
• Milk is warm or too
hot to foam.
• Usecold,fresh(orfreshlyopened)milk.
• Do not re-foam already heated milk.
• Try reducing the quantity of milk in the milk jug.
• Tryadierentmilk.Somemilksandmilkbrands
produce more froth than others. For example, we
have found that some soy milks produce froth while
othersdonot.Experimentwithdierentmilkoptions
and frothing discs to achieve the desired result.
• Adding dense ingredients like thick syrups, heavy
powdersandlargeakescansignicantlyreduce
the amount of foam.This is normal.
Milk is not
heating?
• Ensure the milk jug is correctly positioned onto the
power base.
• Ensure that the milk frother has been properly
activated. Frothing has started once the milk frother
beepsonceandthebuttonsurroundslowlyashes.
If the milk frother does not do this, re-push the
START/STOPpush-dialonce,rmly.
• Increase the temperature by turning the
START / STOP push-dial to the right.
Frothing
disc is not
moving or is
dislodged?
• Frothing disc is not
inserted correctly.
• Frothing disc
has dislodged
during operation.
• Ingredients have
been added too
quickly.
1. Stop operation.
2. Remove liquid from milk jug.
3. Ensure the frothing disc is securely and correctly
attached. Refer to steps 2 & 3, page 7. Once
attached,turnthefrothingdiscwithyourngers,
it should turn freely. If it doesn’t, contact Sage®
Consumer Service.
4. Rellmilkjugwithliquid.
5. Startfrothing.Addingredients(ifdesired)slowly
and in small quantities after the milk has already
started swirling.
3 beeps?
• The milk frother may
be overheated.
1. Unplug the cord from the power outlet.
2. Remove liquid from milk jug. Rinse the milk jug and
frothing disc with cold water then dry thoroughly.
3. Ensure the milk frother has not been operated
for 5 minutes. This allows the internal components
to cool.
4. Ensure the frothing disc is securely and correctly
attached. Refer to steps 2 & 3, page 7. Once
attached,turnthefrothingdiscwithyourngers,
it should turn freely. If it doesn’t, contact Sage®
Consumer Service.
5. Recommence frothing.

11
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE WHAT TO DO
Humming
noise?
• This is normal.
It is the cooling
fan preventing the
milk frother from
overheating.
• During this time, you may still use the milk frother
unless the Boil Dry Overheat Protection as been
activated(3beepswillbeheard).Followthe
instructions above.
Burnt milk?
• Milk is not swirling
correctly.
• Milk jug has not
been cleaned
properly and milk
residue from previous
use is burning.
• Ensure the frothing disc is securely and correctly
attached. Refer to steps 2 & 3, page 7. Once
attached,turnthefrothingdiscwithyourngers,
it should turn freely. If it doesn’t, contact Sage®
Consumer Service.
• Ensure the milk jug is thoroughly cleaned after
each use and between consecutive uses.
Ingredients
are not
melting?
• Ingredients have
been added before
milk has warmed up.
• Ingredients are
too large.
• Always allow the milk frother to start for a few
seconds before using the measuring cap to
gradually add ingredients.
• Ensure ingredients are in small pieces.
Milk is too
cold / too
hot?
• Adjust the temperature to suit your personal preference.
• AlwaysllthemilkjugbetweentheMINand
MAX level markings.
Grinding
noise?
• Frothing disc is not
inserted correctly.
• Frothing disc has
dislodged during
operation.
• The milk jug has
been removed from
the power base
during operation.
• Ensure the frothing disc is securely and correctly
attached. Refer to steps 2 & 3, page 7. Once
attached,turnthefrothingdiscwithyourngers,
it should turn freely. If it doesn’t, contact Sage®
Consumer Service.
• Removing the milk jug during operation can dislodge
the frothing disc. Stop operation. Reinsert the
frothing disc correctly before recommencing.
Emergency
stop?
• To stop operation at any time, press the centre of
the START/ STOP push-dial. Operation has stopped
oncethebuttonsurroundhasstoppedashing.