Salamander Designs FPSA/MSB User manual

Surface Hub Battery Storage Case 501-738 v11.21 page 1 of 8
Surface Hub Battery Storage Case Installation
FPSA/MSB
Electronic Stand Installation see pages 2-4
Fixed Height Stand Installation see pages 5-7
PARTS
ID QTY Part # DESCRIPTION
A 2 302-300 10-32 X 3/8” BUTTON HEAD CAP SCREWS
B 4 300-485 1/4-20 X 1/2" BUTTON HEAD SOCKET CAP SCREWS
C 1 400-080 5/32” HEX KEY
D 8 400-125 VELCRO ONE-WRAP STRAP, - 1/2 X 8” LONG
E 1 300-496 5/32 x 25mm HEX BIT
F 1 400-178 .261” DRILL BIT
G 6 300-515 1/4” ID X 5/8” OD NEOPRENE BONDED WASHER
H 1 400-170 1/8” HEX KEY
I 4 300-532 1/4-20 NE NYLON LOCK NUT
B
C
E
F
G
H
I
A
D

Surface Hub Battery Storage Case 501-738 v11.21 page 2 of 8
1. Bracket Install
Using the provided hex key, loosen the two screws indicated.
NOTE: Do not remove these screws as they are used to support internal components.
Loosen only enough to install the two L Brackets as shown at right. Tighten only enough
to maintain orientation shown.
2. Bracket Alignment
A. Attach the Storage Case by inserting the support tabs into the two slots ensuring that the
two L Brackets fall inside of the Storage Case.
B. Gently push the Storage Case down until the support tabs are seated in the slots.
C. Secure the Storage Case by installing the two 10-32 x 3/8” button head cap screws through
the support tabs and into the L Brackets.
D. Tighten the L Bracket screws that were installed in the previous step.
E. Remove the Storage Case by removing the 10-32 x 3/8”” button head cap screws.
1032 X 3/8”
BUTTON HEAD SOCKET
CAP SCREW 2X
Installing on Electric Lift Mobile Stand

Surface Hub Battery Storage Case 501-738 v11.21 page 3 of 8
3. Secure Battery
Attach Battery to Storage Case using four screws (#300-485) and four washers (#300-515),
rubber side down.
Tighten screws with hex key provided.
4. Install Battery and Storage Case
Resecure with the 10-32 fasteners as shown on step 2.
Attach the supplied hook and loop straps to
manage wiring inside and to attach power cord
from the battery when not charging. Use these
locations to secure the straps and wiring in
the next step.
BACKPACK TOP
STORAGE CASE

Surface Hub Battery Storage Case 501-738 v11.21 page 4 of 8
5. Wire Management
Manage cables carefully. Use cable ties to keep
wires away from pinch points.
Route Cable from Display to Stand
Manage cables through cable chain by
pushing cable through finger keeper
on inner side of chain direction shown
in arrows.
Plug AC and DC cables and USB into their
respective locations on the Surface Hub then
run the cables through the Stand and connect
to Battery.
B.
A.
B.
A.

Surface Hub Battery Storage Case 501-738 v11.21 page 5 of 8
1. Determine Drill Locations
Place the 11 x 17 drilling template provided over the Stand Cubby Cover and align the two horizontal lines
on the template shown at left with the top and bottom edges of the slot in the Cubby Cover.
Align the left edge of the template with the inside edge of the Cubby Cover slot.
Align the top long edge of the template with the line created where the Cubby meets the
Upper Rear Cover.
Tape the template to the Cubby Cover and drill two clearance holes for 1/4-20 holes with the
drill bit provided at the center of the “X” locations.
2. Attach Brackets
Attach the two L Brackets loosely (but tight enough to maintain the orientation shown) through
the drilled holes using the two 1/4-20 x 1/2” Button Head Screws into the two 1/4-20 Nylon Lock Nuts.
1/420 x 1/2” BUTTON HEAD SCREW 2x
L BRACKET 2x
1/420 NYLON
LOCK NUT 2x
CUBBY COVER SLOT
UPPER REAR COVER
CUBBY COVER
Installing on Fixed Height, Mobile Stand

Surface Hub Battery Storage Case 501-738 v11.21 page 6 of 8
3. Bracket Alignment
Attach the Storage Case by inserting the support tabs into the two slots ensuring that the
two L Brackets fall inside of the Storage Case.
Gently push the Storage Case down until the support tabs are seated in the slots.
Secure the Storage Case by installing the two 10-32 x 3/8” button head cap screws through
the support tabs and into the L Brackets.
Tighten the L Bracket screws that were installed in the previous step.
Remove the Storage Case by removing the 10-32 x 3/8” button head cap screws.
4. Secure Battery
Install the battery to the Storage Case using the four 1/4-20 x 1/2” Button Head Cap Screws and
Bonded Washers as shown. Ensure the Bonded Washers are installed with the rubber side down.
Ensure that the battery is installed in the orientation shown, with the AC OUT and DC OUT ports at
the top of the Storage Case.
BACKPACK TOP
STORAGE CASE
1/4-20 x 1/2” BUTTON HEAD
SOCKET CAP SCREW (2x)
BONDED WASHER (4x)
1032 x 3/8” BUTTON HEAD
SOCKET CAP SCREW 2x

Surface Hub Battery Storage Case 501-738 v11.21 page 7 of 8
LIMITED WARRANTY FOR COMMERCIAL VIDEO DISPLAY STANDS AND MOUNTS
Salamander is proud to stand behind our products with industry-leading warranties. Should you ever encounter any problem with your
Salamander product, let us know. We are here to make it right. 1.800.535.5659 - 860.761.9500
Full warranty including limitations and warranty claim information may be found at www.salamanderdesigns.com/commercial/warranty
5. Install Cables and Storage Case –
Run Cables Through Stand
Remove the Upper Rear Panel by first removing
the two 1/4-20 x 1/2” screws and then tipping
the Panel back enough to allow lifting the Panel
o of the two Upper Rear Panel Studs.
Next run wires thru the oval cutout behind the
display and the grommeted hole in Upper Rear
Panel and replace the Upper Rear Panel.
Plug in the AC Power Cord, then the cables
from the stand and reinstall Backpack with
battery and resecure with the 10-32 fasteners.
1/420 x 1/2”
SCREW 2x
WIRE
PATH
UPPER REAR PANEL
UPPER REAR PANEL STUDS
5. Secure Cables
Use the supplied hook and loop straps to
manage wiring inside and to attach power cord
from the battery when not charging. Use these
locations to secure the straps and wiring.