Salamander Designs UNIFI HUDDLE D1/338AM1 User manual

Salamander Uni Huddle, Single Mount 1 of 12 501-710 [6.19]
TIP HAZARD WARNING!
Cabinet must be affixed to wall.
For use with video monitors weighing 175lbs (80kg) or less. Use with
heavier televisions may result in instability causing tip over resulting
in death or serious injury.
UNIFI HUDDLE - SINGLE MOUNT
D1/338AM1 ASSEMBLY INSTRUCTIONS

Salamander Uni Huddle, Single Mount 2 of 12 501-710 [6.19]
warnings
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS FURNISHING
WARNING! – Failure to comply with these instructions may result in accident involving serious personal
injury. Failing to follow these instructions can result in the product being damaged or being destroyed or
voiding of the warranty.
WARNING! – For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions
may result in instability causing tip over resulting in death or serious injury.
CAUTION!
• Close supervision is necessary when this furnishing is used by or near children, invalids,
or disabled persons
• Use this furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
• Do not use outdoors
• For Commercial Use Only
Weight Capacities – Max Load: 175 lbs (80kg)
***** SAVE THESE INSTRUCTIONS *****
Accessories and Spare Parts
Please contact Salamander Designs 860.761.9500 or www.salamanderdesigns.com

Salamander Uni Huddle, Single Mount 3 of 12 501-710 [6.19]
A
B
C
D
E
F
G
H
J
K
L
N
M
O
P
Q
R
S
PAR T S
ID PART NUMBER DESCRIPTION
A 300-518 1/4-20 x 3/8” Button Head Socket Cap Screw
B 300-486 1/4-20 x 1.25” Button Head Socket Cap Screw
C 300-365 Leveler 3/8-16 x 1.5”
D301-745 Hollow Wall Anchors
E 301-055 3/8” 2” Alligator Wall Anchors
F 300-465 1/4-20 x 3/4” Socket Cap Screws
G 300-835 Universal Shelf Peg
H 300-565 Drop In Nut
J 301-730 5/16 x 2.5” Lag Bolt
K 300-468 1/4” Flat Washer
L CA/BS Brush Seal Set w/Adhesive
M 301-260 1/4-20 Joint Conn Bolt
N 400-035 Leveler Wrench
O 300-485 1/4-20 x 1/2” Button Head Socket Cap Screw
P 300-542 Joint Connector Bolt, 5/16-18 x 1.5”
Q 203-740 Shelf, Single Camera Mount
R 301-845 1.5 x .75” Extrusion
S 304-056 Joint Connector Bolt, 1/4-20 x .75”

Salamander Uni Huddle, Single Mount 4 of 12 501-710 [6.19]
1. ATTATCH LEG TO TABLE
A. Attach leveler (C) to leg as shown.
Hand tighten loosely.
C
B. Attach desk leg to table support
using four A screws.
A (4x)
2. ATTATCH TABLE TO CABINET
Attach table to cabinet using four B screws.

Salamander Uni Huddle, Single Mount 5 of 12 501-710 [6.19]
3. INSTALL display brackets
Fasten the brackets using fasteners (length and size recommended by the display manufacturer.
To prepare for Tech Shelf height:
A. Measure from center hole in display
bracket to either the top or bottom of
the display to set tech shelf height.
B. Add one half height of device plus
clearance desired for bottom camera
placement or clearance above display
(Note: Tech Shelf may be afixed
above or below display).
4. attach tech shelf (Optional)
Attach tech shelf to display header using screws C and nuts D.
(Hardware included in tech shelf.)
Tech Shelf Post
C (2x)
D (2x)
Display Header
C
D
Camera Post
Note: Attach Tech
Shelf to post after
mounting display
(step 9).

Salamander Uni Huddle, Single Mount 6 of 12 501-710 [6.19]
5. LEVEL CABINET AND MARK WALL
Wall Mount Bracket
Jam Nut
Loosen jam nut with supplied wrench
and tighten to the locked position.
WARNING! This step requires two people.
A. Prior to fastening to wall, it is important to level the cabinet with the
floor by verifying that feet are properly adjusted.
B. Place cabinet in desired location and mark bracket
holes. Once holes have been marked move cabinet.

Salamander Uni Huddle, Single Mount 7 of 12 501-710 [6.19]
Drill 1/2” diameter hole. Hold metal channel
flat alongside plastic straps and slide chan-
nel through hole.
Hold ends of straps between thumb and
forefinger and pull toward you until channel
rests flush behind wall. Slide plastic cap along
straps with either hand with flange of cap is
flush with wall.
Snap straps at wall by pushing side to
side,snapping of straps level with flange
of cap.
Move cabinet to wall and attach bracket.
Insert bolt through Bracket and tighten
until snug against wall.
Install wall fasteners to marked location on wall & fasten cabinet.
6A. install WALL FASTENERS (most applications)
A B
C D
WOOD: Locate two framing studs using a stud finder device. 3/16” bit, use lag bolt (J) only.
Drill to 2.5” (63mm) depth.
MASONRY: Place brackets in desired location. 3/8” bit, use lag bolt (J) and wall anchor (E).
6B. install WALL FASTENERS (ALTERNATE)
A
Place cabinet in place and fasten with washers K and lag bolts J.

Salamander Uni Huddle, Single Mount 8 of 12 501-710 [6.19]
7. install Brush seal
Use with baseboard molding, trim work or gaps in uneven wall surfaces.
Brush Seal Holders should stay flush to surface so that ONLY brush is showing.
Peal o tape backing and from the inside of the cabinet install to inside
wall surface of end panel indicated (below center), orient the brush steal
so that the “L” shaped surface faces toward the inside of the cabinet.
Inside Wall of End Panel
“L” surface

Salamander Uni Huddle, Single Mount 9 of 12 501-710 [6.19]
8. install Shelves
A
B
Insert into post channel
and slide to desired height.
Level shelf by adjusting
shelf peg positions and
tighten screw using hex key.
Note: Drop-in nut must
make a 1/4 turn in post.
Assemble loosely as shown.
I
S
B
Drop-In Nut Option
Should you desire shelf placement in location other than
predrilled locations, use the drop-in nut option.
This option allows shelf to be placed at any height.
NOTE: Shelf pegs can be re-positioned if desired.
A. Place shelves on pegs.
B. Install shelf stops in front or back of shelf as desired.
C. Shelf placement can be adjusted if necessary to either pre-drilled.
locations or any location using Drop-In Nuts (B) supplied.
D. Install accessories (IR Repeater Kit, Power Conditioner, etc) and place components.
C

Salamander Uni Huddle, Single Mount 10 of 12 501-710 [6.19]
9A. install display to mount
Install display to header mount by inserting the four shoulder washers
on the display brackets through the keyhole openings. Be sure that the
shoulder washers rest at the bottom of the keyhole openings.
WARNING! This step requires two people.
P
Q
R
9B. INSTALL TECH SHELF TO MOUNT
Attach Tech Shelf (Q) to Shelf Post
(R) using two (P) screws as shown.
9B. install TECH SHELF to mount
Attach Tech Shelf (Q) to Shelf Post (R) using two (P) screws as shown.
P
Q
R
9B. INSTALL TECH SHELF TO MOUNT
Attach Tech Shelf (Q) to Shelf Post
(R) using two (P) screws as shown.

Salamander Uni Huddle, Single Mount 11 of 12 501-710 [6.19]
Modesty Panel
Removing and Re-Installing
NOTE: Be sure bottom of modesty panel is flush to cabinets top.
ADJUSTMENT TIPS
3U Vertical Rack (INCLUDED)
Remove
Loosen screws on both sides.
Then tilt rack until the hook is
free and lift up until the rack is
free from bottom screw.
Re-Install
Slide the slotted ends of the
rack over the bottom screw and
hook the top screw as shown.
Tighten with provided
Hex Key.
A B
S
(2x)
To remove or re-install the Modesty Panel, remove S bolt with the hex key supplied.
To remove or re-install the Modesty Panel, remove S bolt with the hex key supplied.

Salamander Uni Huddle, Single Mount 12 of 12 501-710 [6.19]
Main Adjustment (Side to Side and Up/Down)
Adjustment is made by turning screw (A) in and out.
Dismount Hinge from Hinge Plate
With one hand holding the door open, pull
back on the hinge quick-release lever (B).
Door Front
Adjust the tops of the doors to be
parallel to the top of the cabinet.
A
A
A
ADJUSTMENT TIPS
DOORS
NOTE: It is important that cabinet is level before adjusting doors.
A
B
LIMITED WARRANTY FOR COMMERCIAL VIDEO DISPLAY STANDS, MOUNTS AND HUDDLE
Salamander is proud to stand behind our products with industry-leading warranties. Should you ever encounter
any problem with your Salamander product, let us know. We are here to make it right. 1.860.761.9500
Full warranty including limitations and warranty claim information may be found at
www.salamandercommercial.com/warranty