Salamander Designs CHAMELEON User manual

TIP: For Innitely Adjustable Shelves please skip ahead to “Fine Tuning & Tips.”
At this point you may install accessories (IR Repeater Kit, Power
Conditioner, Etc.) and place components.
TIP:
Socket Screw 1.25”
303-520
(Wood Tops Only)
Socket Screw 1”
(Use with Shelf Peg)
300-455
Optional: Innitely Adjustable Shelf Kit (See Fine Tuning)
(PHK-2070)
Drop-In Nut
(Use with Shelf Pegs)
300-565
Socket Screw 3/4”
(Use with Shelf Peg)
300-465
Shelf Pegs
300-835
You will need a Phillips head screwdriver to assemble your Chameleon Cabinet.
Rubber Pads
303-380
(Glass Tops Only)
chameleon
ASSEMBLY INSTRUCTIONS
TM
Hex Key 3/16’’
400-060
Hex Key 4mm
400-170
Congratulations on your purchase!
For any questions please call us at:
800.535.5659 / 860.313.0525 (9am-5pm EST)
Visit our website at: www.salamanderdesigns.com
© 2018 Salamander Designs Ltd. Doc No. 501-500 / v 07.18
Chameleon Hardware
2Install Shelves
Assemble shelf pegs with
socket screws (300-455).
Ax shelf peg assembly
to post at desired position
and secure using hex key.
Remove plastic coating from shelves and place onto shelf pegs.
C
B
A
LIMITED WARRANTY
Salamander warrants against manufacturing defects for the lifetime of the product.
Salamander will repair or replace, at our option, any product defective in materials or craftsmanship.
Note: Twin cabinet shown. Follow same process for all congurations.
Speaker Grill Removal
(Applicable Models Only)
Remove by lifting up and out.
A
Media Drawer Assembly
Set drawer liner (303-555)
on bottom of tray.
Place media organizer
(303-310).
Note: Horizontal grooves.
Media Organizer
Drawer Liner
A
B
Chameleon Options
1Level Cabinet
Prior to installing components, it is important to level the cabinet with the oor.
Verify that all of the feet are properly adjusted to support the cabinet evenly.
Leveler Foot
Loosen jam nut with supplied wrench
and tighten to the locked position.
Wrench included.
Jam Nut
Wood Block Foot
Lift cabinet and adjust leveler by hand.
Leveler
(Applicable Models Only)

TIP: You may need to wiggle the rear panel to set it into place.
TIP: If you have a TV Mount, install it before securing the Top.
4Install Door Pulls
5Rear Panels
Fine Tuning/Tips
Secure pulls with screws
using a Phillips screwdriver.
Locate the rear post channels.
Lead one end of the rear panel into a
post channel.
Compress the rear panel rmly into
the opposing post channel.
Aligning Doors
Innitely Adjustable Shelves
Assemble loosely as shown.
Insert into post channel and slide to desired height.
Level shelf by adjusting shelf peg positions and
tighten screw using hex key.
Note: Drop-in nut must make a 1/4 turn in post.
Main Adjustment (Side to Side and Up/Down)
Adjustment is made by turning screw (A) in and out.
Dismount Hinge from Hinge Plate
With one hand holding the door open, pull
back on the hinge quick-release lever (B).
Follow these instructions if you wish to adjust your doors.
Socket Screw 3/4’’
(300-465) Shelf Peg
Drop-In Nut
(300-565)
Door Front
Adjust the tops of the doors to be
parallel to the top of the cabinet.
A
A
B
C
A
A
B
B
3Place & Secure Top
Place Rubber Pads (303-380) on the frame covering bolts as shown.
Glass Top
Place the glass top
squarely on the cabinet
with the Salamander Logo
positioned to the back/left
corner.
Wood Top
Align wood top squarely to the cabinet
frame with the holes closest to edge of
top, positioned to the rear of cabinet.
Fasten top to the frame using screws (303-520).
A
B
A
B
(Applicable Models Only)