Salamander Designs Arc AT/6P/G2 User manual

14’ Arc™ Meeting Table (6 Person) Assembly 5017806 v10.23 page 1 of 8
14’ Arc™ Meeting Table (6 Person)
AT/6P/G2
ASSEMBLY

14’ Arc™ Meeting Table (6 Person) Assembly 5017806 v10.23 page 2 of 8
PAR T S
ID QTY PART NUMBER DESCRIPTION
(3) 205-6030 ARC Table Top Segment
A (12) 302-355 8-32 x 1/2” Modesty Panel Fastener
B (12) 300-485 1/4-20 x 1/2” Cable Raceway Mounting Screw
C (48) 300-585 1/4-20 x 3/4” Leg Mounting Screw
D (2) P-305-590/BO/CM Table Leg with Wireloom
E (6) P-305-590 Table Leg
F (6) 305-585 Cable Raceway
G (2) 204-300 Cable Raceway Bridge
H (3) 204-320 Modesty Panel
302-355
8-32 x 1/2"
Modesty Panel Fastener
ABC
300-485
1/4-20 x 1/2”
Cable Raceway
Mounting Screw
300-585
1/4-20 x 3/4”
Leg Mounting Screw
EF
G
204-300
Cable Raceway Bridge
P-305-590
Table Leg
305-585
Cable Raceway
H
204-320
Modesty Panel
205-6030
ARC Table Top Segment
(Bottom View)
D
P-305-590/BO/CM
Wireloom with Leg

14’ Arc™ Meeting Table (6 Person) Assembly 5017806 v10.23 page 3 of 8
Attach 2 cable raceway brackets (E) to non-grooved side of each modesty panel (H). Insert (A2) through
modesty panel and fasten bracket in place with (A1).
1. Modesty Panel
Modesty Panel
Non-grooved side Cable Raceway
BEFORE YOU BEGIN
Table will be assembled starting with the left (seated) segment.
WIRELOOM
Place table leg (D) with pre-installed wireloom at
desired location. Typically installed in the back
side of the table towards the center for wire
management to the floor.
ACCESSORIES
If your tops have cut-in accessories such as a
cable port or charger be sure to select the
tops in the order intended from left to right
seated position.
LEFT
1
RIGHT
3
2
A1 X12
A2 X12
D X2
SCREEN

14’ Arc™ Meeting Table (6 Person) Assembly 5017806 v10.23 page 4 of 8
2. Table Segment #1
A. Attach Legs
Use (6) C screws to attach the two legs to the mating edge of top.
Use (8) C screws to attach the two outer legs to the top.
B. Acoustic Panel
Attach the acoustic modesty panel to the table top using B screws.
Note: Some flexing of the metal cable raceway may be required to align the mounting holes (closer to the
bend) with the table inserts.
A
Mating Edge
(3) C Screws
Outer Edge
(4) C Screws
Mounting Hole
B
A
C X14
B X4

14’ Arc™ Meeting Table (6 Person) Assembly 5017806 v10.23 page 5 of 8
3. Table Segment #2
A. Attach Legs
Use (3) C screws per leg.
B. Accoustic Panel
Use (1) B screws per bracket.
B X4
B
A
Flip the table segment 2 and position it over the mounting plates of the standing table leg.
Attach (3) C screws to each leg from underneath the table, connecting the two table segments.
If needed, slightly loosen the bolts on the mating legs to ensure proper hole alignment and a snug fit.
C. Join Table Segments
C X6
C X6

14’ Arc™ Meeting Table (6 Person) Assembly 5017806 v10.23 page 6 of 8
Flip the table segment 3 and position it over the mounting plates of the standing table leg.
Attach (3) C screws to each leg from underneath the table, connecting the two table segments.
If needed, slightly loosen the bolts on the mating legs to ensure proper hole alignment and a snug fit.
C. Join Table Segments
4. Table Segment #3
A. Attach Legs
Use (3) C screws per leg.
B. Accoustic Panel
Use (1) B screws per bracket.
C X8 B X4
C X6
B
A

14’ Arc™ Meeting Table (6 Person) Assembly 5017806 v10.23 page 7 of 8
Insert cable bridge by sliding it in from the side of the cable raceway, towards the gap between the
modesty panel and the table segments.
6. Install Cable Bridge
Centered between table segments.
Position table in the desired location and level if needed using the threaded leveling feet.
5. Level Table
Threaded Leveling Foot
CAUTION: When relocating the assembled table, exercise caution and ensure
that each section is adequately supported during the move.
Leveling Direction

14’ Arc™ Meeting Table (6 Person) Assembly 5017806 v10.23 page 8 of 8
LIMITED WARRANTY FOR COMMERCIAL VIDEO DISPLAY STANDS AND MOUNTS

Salamander is proud to stand behind our products with industry-leading warranties. Should you ever encounter any problem with your
Salamander product, let us know. We are here to make it right. 1.800.535.5659 - 860.761.9500

Full warranty including limitations and warranty claim information may be found at www.salamanderdesigns.com/commercial/warranty
Place and secure ports and chargers into the designated openings on the tabletop.
7. Install Ports