Salamander Designs Lilliana User manual

Lilliana - 500-922 v8/20 page 1 of 6
Lilliana
Assembly Instructions
Thank you for your purchase.
Unpack all content and check to
ensure that all of the parts are in
proper condition. To help protect
the environment, use the appropriate
recycling and discarding methods
for the packaging items.
Read ALL assembly instructions
before beginning. If you have any
questions, please contact your
installator or Salamander Designs
at 800-535-5659.
Tool Required:
Philips Screwdriver
PARTS - Supplied with Armless, Left and Right-End Chairs
Connector Bolt
1/4 - 20 x 2”
Part# 014978
123
4
¼ - 20 x 2½”
Connector Bolt
Part# 015255
Pre-installed in seatback
¼ - 20
Hex Nut
Part# 005489
Spacers

Lilliana - 500-922 v8/20 page 2 of 6
2Power Seating - Optional
1Tactile Transducer - Optional
Tactile Transducer
If you have purchased a Tactile Sound
Transducer for your chair(s), install
before connecting seats.
Remove back panel and screw
transducer onto bolt on chair frame.
A. Connect recliner controllers
to motors.
B. Connect power supplies
to motors.
Coil & Tie Extra Wire Length.
Be careful to route wires away
from mechanism.
2-pin adaptor cord

Lilliana - 500-922 v8/20 page 3 of 6
3Connecting Seats to Arms
A. Position chairs and connectors in
the location that they be installed.
Align front and back bolt holes.
(End Chair to Straight or Wedge Connector)
B. Extend foot rest to access
front bolt holes and secure
connection by inserting bolts
through chair and into arm.
C. Raise lower back panels
and locate the back bolt holes.
Secure connection by
inserting bolt through
chair and into arm.
Spacer
Spacer info:
• Spacers are needed when connecting seats to arms.
Each side of a seat that does not have an arm needs
a spacer.
• Spacers match the shape of the chair bases and are
attached along the side of the base.
Example:Inacongurationof4recliners6spacersareneeded.
B. Connect power supplies
to motors.
Coil & Tie Extra Wire Length.
Be careful to route wires away
from mechanism.
2-pin adaptor cord

Lilliana - 500-922 v8/20 page 4 of 6
4Connecting Seat to Seat
A. Extend foot rest to access
front bolt holes.
Insert two spacer panels
between chairs
(align bolt holes).
Secure connection by inserting
bolt through chair frames.
Align front and back bolt holes.
Fasten with nut.
(Without Arms Between Seats - Max of 3 Seats)
B. Secure connection by inserting
bolt (1) through chair frames.
Fasten with nut (2).
12
1
2
Inthisconguration2spacersareneeded
between each seat.
2 spacers are needed
between seats.
2 spacers are needed
between seats.

Lilliana - 500-922 v8/20 page 5 of 6
5Attaching Back Rests
A. Return seat to upright position.
Remove pre-installed phillips
screws. Lower seatback over
the chair mechanism.
B. Press down to align the backrest
screw holes to the upper and
lower holes in the chair
mechanism tongues.
Install and tighten screws.
C. Recline chair and fasten seatback
 apunderrearedge.

Lilliana - 500-922 v8/20 page 6 of 6
Warranty:
For Salamander Seating Limited Warranty details:
https://www.salamanderdesigns.com/customer-service/warranty/
Leather care tips:
Leatherisanaturalproductandvariationsincolorcanoccur,alongwithminorawssuchas
scars and other markings that give each hide its own unique character. The subtle markings
on leather distinguish genuine leather from manmade materials.
We recommend that you look after your chair by not exposing it to direct sunlight or placing it
too close to a heat source, such as a radiator, which will cause the leather to dry. To remove
any dust and dirt we recommend vacuuming with a soft brush. To remove simple stains (water
soluble), please use a soft cloth or sponge with a little water. For more professional care and
to prolong the life of the leather, we recommend the products from Leather Master.
Fabric care tips:
Removeballpointpen,redwine,mustard,cola,tea,coee,orange,andgrapejuiceusingmild
liquid soap and lukewarm water. Rub soap foam in circular motion with sponge or soft brush.
Pat area dry after cleaning. When completely dry, brush in the direction of the nap.
Powered Seating:
PowerMechanismElectricalSpecications:110VAC,2.0ampsnominalload,5.0ampsmax
load, thermally protected.
We recommend a small size power strip to connect multiple power chairs. It is also possible
toutilizemultipleY-typesplitterstoconnectchairsinseries.Pleasenotethespecicationsof
the power components and be cautious not to overload the electrical circuit.
phone: [phone]
www.SalamanderDesigns.com