Salus Ep110 User manual

Installation Manual

Model: EP110

Single channel programmable controller

Product Compliance ................................................................................................. 3

Safety Information ...................................................................................................... 3

Box content .................................................................................................................... 3

Introduction ................................................................................................................... 4

Features ............................................................................................................................. 4

Installation ....................................................................................................................... 5

Button functions and LCD icons ........................................................................ 7

Operations ....................................................................................................................... 8

Functions ......................................................................................................................... 14

Factory Reset ................................................................................................................. 16

Technical Info ................................................................................................................ 17

Warranty ........................................................................................................................... 18

Contents

02 EP110 Installation Manual

Product compliance

Safety Information

Box content

This product complies with the essential requirements and other relevant provisions of the following EU

Directives: 2014/30/EU, 2014/35/EU and 2011/65/EU. Please check www.saluslegal.com for the full information.

Use in accordance with the EU and national regulations. For indoor use only. Keep your device completely

dry. This product must be installed by a competent person and in accordance with all the EU and national

regulations.

Always isolate the AC Mains supply before installing or working on any components that

require 230 VAC 50Hz supply.

The box includes the EP110 controller, 2X screws and plugs and the Quick Guide installation manual.

Backlight/

Holiday

Mode

+1Hr

Down

Select

Set

Reset

Installer Manual-Quick Guide

Always isolate the AC Mains supply before installing or working on any components

that require 230 VAC 50Hz supply.

Introduction

A programmable controller is used to switch the heating system and/or

the hot water in your home on and oﬀ as needed. It works by controlling

the central heating and/or the hot water with programmed settings that

take eﬀect at diﬀerent times of the day.

Go to www.salus-manuals.com for the full PDF version of the manual.

Product Compliance

EU Directives: 2014/30/EU, 2014/35/EU and 2011/65/EU. Please check

www.saluslegal.com for the full information.

Safety Information

Use in accordance with the EU and national regulations.

For indoor use only.

Keep your device completely dry.

This product must be installed by a competent person and in accordance

with all the EU and national regulations.

Diﬀerence between EP110/EP210/EP310

Installation Jumper Settings

First Power Up

Button Function

The EP line will oﬀer you the possibility to customize your central heating system

and hot water system as desired.

EP110 is recommended for users that want to control only the Central Heating or

the Hot Water system.

EP210 is designed to give you a full control with only one device of both your

Central Heating and Hot Water system.

EP310 is the most versatile product of this line and lets you manage two diﬀerent

Central Heating zones and the Hot Water with only one controller.

Model: EP110/EP210/EP310

Input: 230V, 50Hz

Output: 3A/ switch terminal

EP110 Volt Free application only

EP210 - 230V Application

EP310 - 230V Application

EP110 - 230V Application Only

Note: Please remove red link wire for this application.

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 Not Used

2 Not Used

3 Volt Free Connection

4 Volt Free Connection

Earth Parking

(no electrical connection)

NL1234

NL123456

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 NC (Output)

2 Not Used

3 Switch Live (Output)

4 230V Common (via Link)

Earth Parking

(no electrical connection)

NL1234

NL123456

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 Hot Water O

2 Central Heating O

3 Hot Water On

4 Central Heating On

Earth Parking

(no electrical connection)

NL1234

NL123456

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 Hot Water O

2 Central Heating O

3 Hot Water On

4 Central Heating 1 On

5 Central Heating 2 On

6 Central Heating 2 O

Earth Parking

(no electrical connection)

NL1234

NL123456

Changes to the jumpers settings should only be made by the Engineer carrying

out the installation or other qualiﬁed person. The installer should select the jumper

positions required if changes need to be made to the factory default settings.

These jumpers are found on the rear of the controller.

* P - Fully pumped system for independent Central Heating and Hot Water.

* G - Gravity Hot Water system with Pumped Central Heating.

EP110/ EP210/ EP310 Switching Bridges

Switch

Program 5-2 days programme or

24h programme

Fully pumped system(P*)

or gravity-fed hot water

system(G*)

Disable/enable the internal

backup battery

System

Feature EP110/310 Settings

Memory

Backup

5-2 24H 24H

5-2

NA NA

OFF ON OFF ON

EP210 Settings

EP110/EP310 EP210

EP110 EP310

EP210

1. Turn on the LCD backlight

2. Press for 3 sec to activate Holiday mode

Select operating mode (ON, ONCE, AUTO, ADV, OFF)

Activate/deactivate Boost function

Decreases the selected setting

Increases the selected setting

Select a clock or programme setting

Sets a clock or programme setting

Reset to Factory settings

EP110

CH or HW

EP210

CH and HW

EP310

2x CH and 1x HW

MODE

SELECT

SET

+HR

EP110 Controller 2x screws and plugs

Quick Guide Installation

EP110 Installation Manual 03

Features

Introduction

A programmable heating controller is used to switch the heating system and/or hot water in your home as

needed. It works by controlling the heating boiler according to a series of programmed settings that take eﬀect

at diﬀerent times of the day. The controller can be set up to 3 programs per day, with complementary Boost

actions and can operate in ﬁve diﬀerent modes. Three diﬀerent sets of time can be set for each day of week,

resulting in a total of 21 settings applicable to the device.

When connected to a system with a non-programmable (digital) thermostat, it can switch oﬀ/on the boiler

and control the heating and/or hot water in your system in a programmed manner. You can use the controller

in a fully pumped and controlled system, where heating and hot water can be operated independently or in

gravity-fed water system, where the central heating cannot be operated without hot water.

The heating system will not work if the programmer has switched it oﬀ. The controller does not detect the

temperature or adjust the heating mode in your house, it just tells the boiler when to switch Oﬀ/On depending

on our individual time settings.

With the controller you don’t have to worry about switching On/Oﬀ your system manually. All you need to do

it so set up the schedules that ﬁt your needs. The controller can be used on your system to control either the

central heating OR the hot water.

• Single Channel Programmer for Central Heater or Hot Water

• 12 or 24 hour clock format

• 5+2 or 24 h individual program with 3 settings per day

• Boost function

• Holiday function

• Advance function

• Memory backup

04 EP110 Installation Manual

Installation

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 NC (Output)

2 Not Used

3 Switch Live (Output)

4 230V Common (via Link)

Earth Parking

(no electrical connection)

NL1234

NL123456

Wiring and terminal description

Terminal Description Backplate

N Mains Neutral

L Mains Live

1 Not Used

2 Not Used

3 Volt Free Connection

4 Volt Free Connection

Earth Parking

(no electrical connection)

NL1234

NL123456

Volt free application. Note: Please remove red link wire (like the one in the picture above) for this application.

230 VAC

Volt Free

EP110 Installation Manual 05

Fix the backplate to the wall. Align the front housing

at the top edge.

Fit the front housing. Press lightly.

Wall mounting

Jumper settings

EP110 Switching Bridges

Switch Feature Setting Default

Program 5-2 days program or

24h program 5-2 24H 5-2 days program

Memory Backup Disable/enable the

internal backup

battery

OFF ON Internal backup

battery disabled

Note: Changes to the jumper settings should only be made by the engineer carrying out the installation

or another qualiﬁed person. The installer should select the jumper positions required if changes need to

be made to the factory default settings. These jumpers are found on the rear of the controller.

The jumpers are found on the rear of your controller and can be used

to change the settings for the program type or internal backup memory

battery. If you want to change the position of your jumpers, please note

that you will need to reset your device. The default position for the jumpers

set a 5+2 program type and keep the internal backup battery oﬀ.

06 EP110 Installation Manual

Button functions and LCD icons

MODE +Hr

SELECT SET

Key Function

Mode Press to select ON/ONCE/AUTO/

ADV/OFF.

+1Hr Press to enter/cancel Boost override

function by setting Boost hours.

Select Press to select the setting of clock/

date/week day, etc.

Set Press to conﬁrm the setting.

Up arrow Press to increase clock/day, press and

hold to enter fast advance.

Down arrow Press to decrease clock/day, press

and hold to enter fast advance.

Press to activate backlight.

Hardware reset

Press and hold button for 3 seconds

to activate Holiday mode.

Select + Set Press and hold buttons to enter clock

setting mode.

Showing when relay is On

Boost hours

Daylight Saving Time On/Oﬀ

Program number

ON Mode Active

(controller runs continually)

ONCE Mode Active

(controller runs for 1 period a day)

Auto Mode Active (controller runs in Auto)

ADV Mode Active

(controller runs in advance override)

OFF Mode Active (controller is oﬀ)

AM/PM

Holiday mode on

Days of the week

5 6 7 8 9

EP110 Installation Manual 07

Operations

Initial power up

After power up or after RESET is pressed, the programmer is reset to factory default settings. During system

reset, all LCD icons and segments are turned on for 2 seconds and all keys are blocked. After 2 seconds and all

keys are released, the programmer is initialized. First the software version is shown and after that the typical

reset display is shown. The time should be 12:00am.

Default settings

Function Status after Reset

Operation Mode Normal mode

Clock 12:00 AM

AM/PM indicator AM

Date January 1, 2016

Daylight Saving Time(DST) On

Program Factory default 5+2

Program Number indicator Off

SET indicator Off

PROG indicator Off

Mode indicator(s) “Off“

Output Relay Off

CH/HW indicator(s) Off

08 EP110 Installation Manual

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

Setting time and date

The ﬁrst thing you will have to do is to set the time and date on your controller. First you will need to set up

the time and then the date. To enter clock setting mode, press and hold Select and Set buttons for 3 seconds.

Please follow the instructions below.

Choose your clock format

Press Up/Down arrow for

12/24 hr format.

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

Press Up or Down to

set the year.

Press Select to confirm.

MODE +Hr

SELECT SET

Press Up or Down to set the

Daylight Saving Time On or Off.

Press Set to confirm.

When Daylight saving time is enabled, the clock will automatically change from Greenwich Mean Time (GMT)

to British Summer Time (BST) on the last Sunday in March. The clock will automatically change back to GMT on

the last Sunday in October.

MODE +Hr

SELECT SET

Choose your clock format

Press Up/Down arrow for

12/24 hr format.

MODE +Hr

SELECT SET

3 sec

Press and hold the

indicated buttons

together for 3 sec.

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

Press Up or Down to set the

month. Press Select

to confirm.

Press Up or Down to set the

day. Press Select to confirm.

MODE +Hr

SELECT SET

Press Up or Down to set

the minutes. Press Select

to confirm.

MODE +Hr

SELECT SET

Press Up or Down to set

the hour. Press Select

to confirm.

EP110 Installation Manual 09

EP110 can operate in 5 diﬀerent modes, described in the table below. EP110 can be set to control either the

boiler OR the hot water. You can choose on which one of the channels you connect the controller. To access

operating modes, please press Mode key.

Operation Mode Function

ON Continuously on

ONCE On for 1 period a day, from Program 1 ON to Program 3 OFF

AUTO Automatic program control

ADV When device is in Auto or Once mode, press the MODE

button for 3 sec for selecting Advance (ADV). This will move

the unit into the next program. When the ADV function

ends the device will return to normal program.

OFF Continuously oﬀ

Operating Modes

MODE +Hr

SELECT SET

For activating the functions described above, press the MODE button. The operating mode is cycled in

the below sequence:

The circle icon will be rotating in a sequence when the relay

output is ON.

ON Mode

MODE +Hr

SELECT SET

Pressing the Mode key once activates the ON Mode. In ON mode, the

controller gives the boiler the ON command, so the heating or the hot

water will run continuously.

ONCE Mode

Pressing the Mode key twice activate the ONCE Mode. In ONCE mode, the

controller gives the boiler the command to run only for one period per

day (from program 1 ON to program 3 OFF)

10 EP110 Installation Manual

MODE +Hr

SELECT SET

ON Mode

MODE +Hr

SELECT SET

Pressing the Mode key 3 times activates the AUTO. In AUTO mode, the

controller gives the boiler the ON/OFF command depending on your

schedule.

OFF Mode

Pressing the Mode key 4 times activates the OFF Mode. In OFF mode, the

controller gives the boiler the OFF command, so the heating or the hot

water will be turned oﬀ.

ADV Mode

Note: In ONCE or AUTO mode, by long pressing the MODE button, the controller will switch automatically

to ADV. You can cancel the ADV by long pressing the MODE key. The device will then return to ONCE or

AUTO mode. You can’t select ADV by pressing Mode key.

MODE +Hr

SELECT SET

Long press Mode while

in Auto or Once

When in Auto mode selecting ADV, the controller will simply toggle the

current auto setting (ON or OFF). For example, if the current program is

set as:

08:00 ON 09:00 OFF 10:00 ON 11:00 OFF

Selecting ADV between 8:00 and 8:59 will change the output to OFF, from

9:00 onwards back to AUTO (which is also OFF). Selecting ADV between

9:00 and 09:59 will change the output to ON, from 10:00 onwards back

to AUTO (which is also ON). If the ADV puts the relay ON then the boost

would apply immediately at the next OFF change, if the ADV puts the

relay OFF then the boost would apply immediately and turn the relay ON.

08:00 OFF 10:00 ON 12:00 OFF 14:00 ON

If ADV occurs at 08:30 and the relay is ON from 08:30 to 12:00. During this period, if at 08:45 +1Hr (Boost) is

pressed, the relay will be ON from 08:30 to 12:00. Boost is applied immediately ie. from 08:45 to 09:45 at the next

change, ie. 12:00. If ADV occurred at 10:30 the relay will be ON from 10:00, OFF from 10:30 (ADV) to 14:00 if no

+1Hr Override. During ADV, if at 10:45 +1Hr (Boost) is pressed, the relay will go ON again at 10:45 (boost starts),

OFF at 11:45 (Boost ends) until ends at 14:00, then ON again at 14:00.

EP110 Installation Manual 11

5-2 Days Program Individual Days Program

Weekdays

3 sets of time/channel

Weekends

3 sets of time/channel

Total: 6 settings/week

1 Day

3 sets of time/channel

Total: 21 settings/week

Programming the EP110

2 types of programs can be set:

• 5+2 (Mo to Fri same and Sat, Sun same)

• Diﬀerent programs for each 24h.

There are 3 diﬀerent time sets for each day.

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

Press Up or Down to select

weekdays or weekends.

Press Select to confirm.

Press Up or Down to

set start time for prog 1.

Press Select to confirm.

MODE +Hr

SELECT SET

Press Set to start programming.

MODE +Hr

SELECT SET

Press Up or Down to set

the minutes. Press Select to

confirm.

MODE +Hr

SELECT SET

Press Up or Down to set

end time for prog 1. Press

Select to confirm.

MODE +Hr

SELECT SET

Press Up or Down to set

the minutes. Press Select to

confirm.

MODE +Hr

SELECT SET

Press Up or Down to

set start time for prog 2.

Press Select to confirm.

Once you have ﬁnished setting the start/end time for the ﬁrst program,

the device will jump into the second program, and then into third and

afterwards into Sat-Sun. Please follow the same steps for each of the

3 programs. Press SET at any time to conﬁrm the setting and return for

program set selection.

Setting the 5+2 program

12 EP110 Installation Manual

Setting dierent programs for each 24h

Note: Don’t forget to move the jumpers to 24h in order to have the individual program active. After

that please follow the same instructions as for the 5-2 days program.

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

Monday will flash. Press Select

to confirm.

Press Up or Down to set

start time for prog 1. Press

Select to confirm.

MODE +Hr

SELECT SET

Press Set to start

programming.

MODE +Hr

SELECT SET

Press Up or Down to set

the minutes. Press Select

to confirm.

MODE +Hr

SELECT SET

Press Up or Down to set

end time for prog 1. Press

Select to confirm.

MODE +Hr

SELECT SET

Press Up or Down to set the

minutes. Press Select

to confirm.

MODE +Hr

SELECT SET

Press Up or Down to

set start time for prog 2.

Press Select to confirm.

Once you have ﬁnished setting the start/end time for the ﬁrst program,

the device will jump into the second program, and then into third and

afterwards into next day. Please follow the same steps for each of the

3 programs. Press SET at any time to conﬁrm the setting and return for

program set selection.

EP110 Installation Manual 13

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

Functions

Temporary Override

ADV Override

ADV only works in AUTO or ONCE mode. During ADV, press MODE once to cancel ADV and go back to AUTO

/ONCE mode after LCD backlight is turned oﬀ. +1Hr override and ADV cannot co-exist in same channel.

During ADV mode, when +1Hr is pressed, override mode will cancel ADV mode then change to Boost mode.

If +1Hr override (Boost) is running, then ADV is selected, ADV will be activated and the previous +1Hr override

will be cancelled.

Boost Override (+1Hr override)

Boost Override (+1Hr override) is available in ONCE/AUTO/OFF modes. Boost mode can be activated even in

ADV mode. When boost mode is activated, ADV is canceled. Press +1Hr at current mode to activate the Boost

Override (+1Hr override) setting mode. Boost mode increases the time of the active program by 1-9 hours.

The new setting hour “+x” (x=last boost hour+1 hour) is displayed. Subsequent press of +1Hr will increase

the duration by 1 hour. Maximum duration is 9 hours. If the number rolls back to blank, this will disable the

Boost Override.

MODE +Hr

SELECT SET

Press +1Hr to enter

Boost override.

MODE +Hr

SELECT SET

The number of boost hours

will be displayed.

MODE +Hr

SELECT SET

To exit boost override, press

mode button until number

+x dissapears.

Long press Mode while in

Auto or Once to enter ADV

override Mode

Short press Mode while in ADV to

exit mode back to auto or Once

3 sec 1 sec

14 EP110 Installation Manual

Holiday Override

During the period of holiday override, relay should be always Oﬀ.

Press and hold at current mode for 3 seconds to activate the Holiday Override setting mode.

The plane icon will be displayed on the LCD and the user’s only option will be to set the number of holiday

days (up to 31). To exit Holiday Override and turn On the relay, long press the key.

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

Press Up/Down keys

to select days.

Enter Holiday Mode

Exit Holiday Mode

MODE +Hr

SELECT SET

Press for 3 seconds.

MODE +Hr

SELECT SET

Controller in current mode.

LCD Backlight

If AC is powered, LCD backlight is activated when or any key is pressed. The backlight will be turned oﬀ in

15 seconds after all keys are released.

3 sec

EP110 Installation Manual 15

Factory Reset

If you want to return to the factory settings please press the Reset button once (use a pin for this action).

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

Press reset button. LCD will turn OFF.

All icons will be displayed. Software version.

Normal Mode.

MODE +Hr

SELECT SET

MODE +Hr

SELECT SET

16 EP110 Installation Manual

Technical Info

Product Specication

Model: EP110

Type: Surface Mounted Wired Single Channel Programmable Timer

Memory Backup Lithium battery (CR2032 x1pc)

Power control

Rating 230V/50Hz/3(1)A

Relay SPDT

Protection Rating: IP 30

Environment

Operating Temperature/

Humidity:

0°C ~ 50°C, 10% – 90% non-condensing

Storage Temperature/

Humidity

-20°C~- 60°C, 10% – 90% non-condensing

Programs

Program 5-2 or 24hr individual program (selectable by jumper),

3 settings/day, with holiday override.

Boost Override Yes, max 9 hours(selectable by software)

Holiday Override Yes, max 31 days (selectable by software)

Clock

Clock Format 12 or 24 hour (selectable by software)

Clock Accuracy +/-1 min/month

Daylight Saving Time (DST) Yes, Clock automatically adjusted if DST is enabled.

EP110 Installation Manual 17

Warranty

SALUS Controls warrants that this product will be free from any defect in materials or workmanship, and shall

perform in accordance with its speciﬁcation, for a period of two years from the date of installation. SALUS

Controls sole liability for breach of this warranty will be (at its option) to repair or replace the defective product.

Customer Name: ..................................................................................................................................................................

Customer Address: .............................................................................................................................................................

................................................................................................................ Post Code: ...............................................................

Tel No: ................................................................... Email: ......................................................................................................

Company Name: ...................................................................................................................................................................

Tel No: .................................................................. Email: ........................................................................................................

Installation Date: ...................................................................................................................................................................

Installer Name: .......................................................................................................................................................................

Installer Signature: ...............................................................................................................................................................

18 EP110 Installation Manual