SAMES KREMLIN FPro S User manual

SAMES KREMLIN N° : 578.027.110-UK-1708
MANUAL AIRSPRAY GUN
PREVENTIVE MAINTENANCE
TRANSLATION FROM THE ORIGINAL MANUAL
IMPORTANT : Before assembly and start-up, please read and clearly understand all the
documents relating to this equipment (professional use only).
THE PICTURES AND DRAWINGS ARE NON CONTRACTUAL. WE RESERVE THE RIGHT TO MAKE CHANGES WITHOUT PRIOR
NOTICE.
SAMES KREMLIN SAS
l
13, chemin de Malacher
38 240 - MEYLAN - France
 : 33 (0)4 76 41 60 60
www.sames-kremlin.com

SAMES KREMLIN - 1 - N° : 578.027.110-UK-1708
Safety instructions :
Never try to stop the spray fan with any part of the body (hands, fingers...) or with
rags.
The operator will need medical attention if the high pressure material spray is in
contact with the body (eyes, fingers…).
Always lock the gun trigger with the safety device when not operating the gun.
Always depressurize air and hoses before carrying out any servicing on the gun.
In order to protect the operator, protective clothing (gloves, respirator mask,
glasses, hearing protective earplug, clothes...) are required.
Use the equipment in a properly ventilated area.
This spray gun is a precision tool. Its correct functioning requires regular maintenance, carried out with care.
When it is carried out directly after use, the cleaning of the gun is faster and easier.
Never use metallic brushes, files or pliers when dismantling the gun.
Before any action on the gun,
Shut off the compressed air supply,
Depressurize the systems by triggering the gun.
Do not use fluid which would quickly clog the nozzle.
Air supply should be clean.
SHORT DURATION SHUTDOWN (LESS THAN 3 HOURS)
Leave the equipment as it is. In any case, if the aircap becomes a little clogged with material, it is best to
clean it with a brush and some solvent.
LONG DURATION SHUTDOWN
Shut off the gun air and fluid supply.
Change material with solvent and trigger the gun to depressurize the hoses and flush the pump, the
hoses and the gun.
Unscrew the air cap. Remove the needle and then remove the fluid nozzle with the wrench provided.
Soak the needle, aircap, fluid nozzle in solvent and brush them carefully, as they are precision parts.
With a brush soaked in solvent, clean the internal parts of the gun. Wash and carefully brush the threated
parts.
If a cup fits the gun, put a cover on the cup to prevent from the paint drying. If not, empty out the paint
and replace it with solvent. Clean the inside and outside part of the cup with a brush soaked in solvent.
Do not soak the gun in solvent.
Use only products or solvent compatible with the parts in contact with the material (refer to
data sheet of the material manufacturer).

SAMES KREMLIN - 2 - N° : 578.027.110-UK-1708
OPERATION TO CARRY OUT FREQUENCY
D W M Q H Y
GENERAL
Check earthings. X
Check leakage from the fittings. X
Check hoses. X
Operate the valves. X
GUN
Clean the outside of the spray nozzle with a soft brush
and solvent. X
Flush the spray gun. X
When the spraying system will not be used for an
extended period of time, take off the nozzle and
immerse it in a solvent-filled container. X
Remove the air valve, clean it if necessary. Grease it
as well as the spring before assembling. X
Change the air valve. Grease it as well as the spring
before assembling. X
Remove the needle as well as the rear line and the
complete air valve. Clean the parts and grease them
before assembling. X
Remove the gun, clean the parts, change the seals
and the defective parts. Grease them before
assembling (refer to seal kit and servicing kit). X
D : daily
W : weekly
M : monthly
Q : quarterly
H : half-yearly
Y : yearly
Nota : Frequencies are given as a clue. They must be adapted by the maintenance service
of the user for every installation according to the product, the working cadence and the
working pressure.