Samson TROVIS 5573 Service manual

Automation System TROVIS 5500
Heating and District Heating Controller
TROVIS 5573
Mounting and
Operating Instructions
EB 5573 EN
®
Electronics from SAMSON
Firmware version 1.82
Edition November 2008

Disclaimer of liability
We are constantly developing our products and therefore, reserve the right to change the prod-
uct or the information contained in this document at any time without notice.
We do not assume any liability for the accuracy or completeness of these mounting and operat-
ing instructions. Moreover, we do not guarantee that the buyer can use the product for an in-
tended purpose. SAMSON rejects any liability for claims by the buyer, especially claims for
compensation including lost profits or any other financial loss, except the damage was caused
intentionally or by gross negligence. If an essential term of the contract is breached by negli-
gence, SAMSON’s liability is limited to the foreseeable damage.
Important safety instructions
For your own safety, observe the following instructions on the installation, start up and opera-
tion of the controller:
4The device may only be installed, started up or operated by trained and experienced
personnel familiar with the product.
4The controller has been designed for use in electrical power systems. For wiring and
maintenance, you are required to observe the relevant safety regulations.
In addition, the following applies to prevent damage to the controller:
4Proper shipping and appropriate storage are assumed.
2EB 5573 EN
Disclaimer of liability/Safety instructions
DANGER!
DANGER indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
WARNING!
WARNING indicates a hazardous situation
which, if not avoided, could result in death or
serious injury.
NOTICE
NOTICE indicates a property damage
message.
Note: Supplementary explanations, information
and tips
Definitions of the signal words used in these instructions
!

ContentsPage
1 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1 Operating controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1.1 Rotary pushbutton . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.1.2 Rotary switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Operating modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2.1 Setting the operating modes. . . . . . . . . . . . . . . . . . . . . . . 7
1.3 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.4 Opening the information level . . . . . . . . . . . . . . . . . . . . . 9
1.5 Setting the controller time . . . . . . . . . . . . . . . . . . . . . . . 10
1.6 Setting the times-of-use . . . . . . . . . . . . . . . . . . . . . . . . 11
1.7 Setting the party mode . . . . . . . . . . . . . . . . . . . . . . . . 13
1.8 Activating the extended information level. . . . . . . . . . . . . . . . 14
1.8.1 Setting public holidays . . . . . . . . . . . . . . . . . . . . . . . . 15
1.8.2 Setting vacation periods . . . . . . . . . . . . . . . . . . . . . . . . 16
1.9 Entering day and night set points . . . . . . . . . . . . . . . . . . . 18
2 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.1 Setting the system code number . . . . . . . . . . . . . . . . . . . . 20
2.2 Activating and deactivating functions. . . . . . . . . . . . . . . . . . 21
2.3 Changing parameters . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.4 Calibrating sensors . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.5 Resetting to default values . . . . . . . . . . . . . . . . . . . . . . . 25
3 Manual mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4 Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5 Functions of the heating circuit . . . . . . . . . . . . . . . . . . . . 46
5.1 Weather-compensated control . . . . . . . . . . . . . . . . . . . . . 46
5.1.1 Gradient characteristic . . . . . . . . . . . . . . . . . . . . . . . . 47
5.1.2 4-point characteristic . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.2 Fixed set point control . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.3 Underfloor heating/drying of jointless floors . . . . . . . . . . . . . . 51
5.4 Deactivation depending on outdoor temperature . . . . . . . . . . . . 52
5.4.1 OT deactivation value in rated operation . . . . . . . . . . . . . . . . 52
5.4.2 OT deactivation value in reduced operation . . . . . . . . . . . . . . 52
5.4.3 OT activation value in rated operation . . . . . . . . . . . . . . . . . 53
5.4.4 Summer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
5.5 Delayed outdoor temperature adaptation. . . . . . . . . . . . . . . . 54
5.6 Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
5.7 Optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
EB 5573 EN 3
Contents

5.8 Flash adaptation . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
5.8.1 Flash adaptation without outdoor sensor (room temperature dependent) . 57
5.9 Adaptation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6 Functions of the DHW circuit . . . . . . . . . . . . . . . . . . . . . 59
6.1 DHW heating in the storage tank system . . . . . . . . . . . . . . . . 59
6.1.1 DHW circuit additionally controlled by a globe valve . . . . . . . . . . 61
6.2 DHW heating in the storage tank charging system . . . . . . . . . . . 62
6.3 DHW heating in instantaneous heating system . . . . . . . . . . . . . 64
6.4 DHW heating with solar system . . . . . . . . . . . . . . . . . . . . 65
6.5 Intermediate heating operation . . . . . . . . . . . . . . . . . . . . 65
6.6 Parallel pump operation . . . . . . . . . . . . . . . . . . . . . . . . 65
6.7 Circulation pump operation during storage tank charging. . . . . . . . 66
6.8 Priority operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6.8.1 Reverse control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6.8.2 Set-back operation . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.9 Forced charging of the DHW storage tank . . . . . . . . . . . . . . . 67
6.10 Thermal disinfection of the DHW storage tank . . . . . . . . . . . . . 68
7 System-wide functions . . . . . . . . . . . . . . . . . . . . . . . . 70
7.1 Automatic summer time/winter time changeover . . . . . . . . . . . . 70
7.2 Frost protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
7.3 Forced operation of the pumps. . . . . . . . . . . . . . . . . . . . . 71
7.4 Return flow temperature limitation . . . . . . . . . . . . . . . . . . . 71
7.5 Condensate accumulation control . . . . . . . . . . . . . . . . . . . 72
7.6 Three-step control . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.7 On/off control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
7.8 Continuous control in control circuit Rk1 . . . . . . . . . . . . . . . . 73
7.9 Releasing a control circuit/controller over the binary input . . . . . . . 74
7.10 Processing of external demand in control circuit Rk1 . . . . . . . . . . 75
7.11 Creep feed rate limitation using a binary input . . . . . . . . . . . . . 76
7.12 Locking manual level . . . . . . . . . . . . . . . . . . . . . . . . . 76
7.13 Locking the rotary switch . . . . . . . . . . . . . . . . . . . . . . . 77
7.14 Feeder pump operation . . . . . . . . . . . . . . . . . . . . . . . . 77
7.15 Setting a customized key number . . . . . . . . . . . . . . . . . . . 77
8 Operational faults . . . . . . . . . . . . . . . . . . . . . . . . . . 78
8.1 Error list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
8.2 Sensor failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
8.3 Temperature monitoring . . . . . . . . . . . . . . . . . . . . . . . . 79
4EB 5573 EN
Contents

8.4 Error status register . . . . . . . . . . . . . . . . . . . . . . . . . . 79
8.5 Sending text messages in case of error . . . . . . . . . . . . . . . . . 80
9 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
9.1 RS-232/modem communications module . . . . . . . . . . . . . . . 83
9.2 RS-485 communications module . . . . . . . . . . . . . . . . . . . . 84
9.3 Description of communication parameter settings . . . . . . . . . . . . 85
9.4 Memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
9.5 Data logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
10 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
11 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . 90
12 Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
12.1 Function block lists . . . . . . . . . . . . . . . . . . . . . . . . . . 93
12.2 Parameter lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
12.3 Sensor resistance tables . . . . . . . . . . . . . . . . . . . . . . . 112
12.4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
12.5 Customer data. . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Key abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 125
EB 5573 EN 5
Contents
Modifications to controller firmware in comparison to previous version
1.80
(previous)1.82 (new)
Internal modifications

1 Operation
The controller is ready for use with the default temperatures and operating schedules.
On start-up, the current time and date need to be set at the controller (–> section 1.5).
1.1 Operating controls
The operating controls are located in the front panel of the controller.
1.1.1 Rotary pushbutton
Rotary pushbutton
Turn [q]:
Display, select parameters and function blocks
Press [ ]:
Confirm adjusted selection or settings
1.1.2 Rotary switch
The rotary switch is used to set the operating mode and the relevant parameters for each control
circuit.
Information level, rotary switch in normal position
Operating modes
Manual level
Day set point (rated room temperature)
Night set point (reduced room temperature)
Times-of-use for heating/DHW
Party mode
Controller time
Configuration and parameter level
6EB 5573 EN
Operation
*
–+

1.2 Operating modes
Day mode (rated operation) : Regardless of the programmed times-of-use and summer
mode, the set points relevant for rated operation are used by the controller.
Night mode (reduced operation) : Regardless of the programmed times-of-use, the set points
relevant for reduced operation are used by the controller.
Stand-by mode : Regardless of the programmed times-of-use, control operation is deacti-
vated. Only the frost protection is activated, if need be.
Automatic mode : During the programmed times-of-use, the controller works in rated opera-
tion. Outside these times-of-use, the controller is in reduced operation, unless control operation
is deactivated depending on the outdoor temperature. The controller switches automatically be-
tween both operating modes.
Manual mode : Valves and pumps can be controlled manually (–> section 3).
1.2.1 Setting the operating modes
1. Turn the rotary switch to (operating modes). blinks on the display.
4For systems with just one control circuit (e.g. Anl 1.0), steps 2 and 3 can be skipped
(selecting the control circuit).
2. Select the control circuit whose operating mode is to be set [q]:
Heating circuit 1
Heating circuit 2
DHW circuit/circulation pump (DHW)
4Only those control circuits are available for selection which can be controlled by the
system schematics (Anl) selected.
3. Confirm the control circuit [ ].
4. Select the operating mode [q]: , , or
5. Confirm the operating mode [ ].
6. Return the rotary switch to normal switch position (information level).
Note: In automatic mode, the momentary stage of the operating schedule ( for day mode or
for night mode) is displayed in the information level together with the icon .
EB 5573 EN 7
Operation

1.3 Display
The display indicates the time as well as information about the operation of the controller when
the rotary switch is at the normal position (information level). The times-of-use together with
temperatures of the various control circuits can be viewed on the display by turning the rotary
pushbutton. The times-of-use are represented by black squares below the row of numbers at the
top of the display. Icons indicate the operating status of the controller.
The controller status can be displayed in the information level (–> section 1.4).
8EB 5573 EN
Operation
Fig. 1 · Icons
Public holiday mode
Vacation mode
Operational fault
Frost protection
Heating circuit 1 Heating circuit 2 DHW circuit
Automatic mode Automatic mode Automatic mode
Night mode Night mode Night mode
Day mode Day mode Day mode
Manual mode Manual mode Manual mode
Stand-by mode Stand-by mode Stand-by mode
Circulation pump UP1* Circulation pump UP2*
Pump output TLP/CP*
Valve Rk1 OPEN Valve Rk2 OPEN
Valve Rk1 CLOSED Valve Rk2 CLOSED Storage tank charging
pump SLP*
Circulation pump ZP*
* UP1, UP2, TLP, CP, SLP and ZP indicate possible choices for pump selection in manual mode.

1.4 Opening the information level
At the normal switch position (information level), the time, date, public holidays and vaca-
tion periods as well as the temperatures measured by the connected sensors and their set points
can be retrieved and displayed.
Note: Data can also be viewed in the operating level (manual mode).
To do so, select Info, confirm and proceed as described below.
Proceed as follows:
1. Select value [q].
Depending on the configuration of the controller, the current values of the following
data points are displayed one after the other:
__:__ Time
Room temperature, heating circuits 1, 2
Outdoor temperature
Temperature at flow sensor VF, heating circuits 1, 2
Temperature at flow sensor VF1, primary heat exchanger circuit
Temperature at flow sensor VF2, VF4, DHW circuit
Temperature at solar collector sensor VF3
Temperature at return flow sensor RüF
Temperature at storage tank sensor SF1
Temperature at storage tank sensor SF2
Temperature at storage tank sensor of the solar circuit
2. By confirming a data point [ ] its set point/limit is displayed. When the time is indicated
on the display, the date appears on pressing the rotary pushbutton.
EB 5573 EN 9
Operation

1.5 Setting the controller time
The current time and date need to be set immediately after start-up and after a power failure of
more than 24 hours has occurred. This is the case when the time blinks on the display.
Proceed as follows:
1. Turn the rotary switch to (controller time).
Display: time, and blink.
2. Edit the controller time [q].
3. Confirm the adjusted time [ ].
Display: year
4. Edit the year [q].
5. Confirm the adjusted year [ ].
Display: date (day.month)
6. Edit the date [q].
7. Confirm the adjusted date [ ].
Display: time
8. Return the rotary switch to normal switch position
(information level).
10 EB 5573 EN
Operation

1.6 Setting the times-of-use
Three times-of-use can be set for each day of the week.
Parameters WE* Range of values
Period/day 1–7 1–7, 1, 2, 3, 4, 5, 6, 7 with 1–7 = every day,
1 = Monday, 2 = Tuesday, ..., 7 = Sunday
Start first time-of-use 6:00 0:00 to 24:00h; in steps of 15 minutes
Stop first time-of-use 22:00 0:00 to 24:00h; in steps of 15 minutes
Start second time-of-use 22:15 0:00 to 24:00h; in steps of 15 minutes
Stop second time-of-use 22:15 0:00 to 24:00h; in steps of 15 minutes
Start third time-of-use – 0:00 to 24:00h; in steps of 15 minutes
Stop third time-of-use – 0:00 to 24:00h; in steps of 15 minutes
* Default values (WE) valid for heating circuits
Proceed as follows:
1. Turn the rotary switch to (times-of-use).
blinks.
4For systems with just one control circuit (e.g. Anl 1.0), steps 2 to 5 can be skipped
(selecting the control circuit and specifying the DHW circuit).
4Only the DHW circuit is controlled in systems Anl 1.5 and 1.9. Therefore the instruc-
tions steps 2 and 3 (selecting the control circuit) do not apply and can be skipped.
2. Select the control circuit, for which the times-of-use are to be entered [q]:
Heating circuit 1
Heating circuit 2
DHW circuit/circulation pump (DHW)
4Only those control circuits are available for selection which can be controlled by the
system (Anl) selected.
3. Confirm the control circuit [ ].
4If control circuit 1 or 2 has been selected, skip steps 4 and 5.
4. Specify DHW circuit [q]:
DHW heating / Circulation pump (DHW)
5. Confirm [ ].
EB 5573 EN 11
Operation

6. Select period/day for which the times-of-use are to be
valid [q]:
1–7 = every day,
1 = Monday, 2 = Tuesday, ..., 7 = Sunday
7. Activate editing mode for period/day [ ].
Display:
START , and blink.
8. Edit start time [q].
(in steps of 15 minutes)
9. Confirm start time [ ].
Display:
STOP
10. Edit stop time [q].
(in steps of 15 minutes)
11. Confirm stop time [ ].
Display:
START
The indicated time corresponds to the stop time for the
first time-of-use plus 15 minutes.
To set the second and third times-of-use, repeat steps 8
to 11.
If no further times-of-use for the selected period/day
are to be programmed, confirm the displayed start
time twice (2x [ ]).
For daily setting, repeat steps 6 to 11 in the same sequence.
Note: Do not use the 1–7 menu to check the programmed times-of-use.
If this menu is opened after the times-of-use have been set, the schedule programmed for Mon-
day is also adopted for all other days of the week.
12. After setting all times-of-use:
Return the rotary switch to normal switch position (information level).
12 EB 5573 EN
Operation

1.7 Setting the party mode
Using the Party mode function, the controller continues or activates the day mode during the
time when the party timer is active, regardless of the programmed times-of-use. When the party
timer has elapsed, the party mode timer is reset to 00:00.
Parameter WE Range of values
Continue/activate rated operation 0 h 0 to 48 hours
Proceed as follows:
1. Turn the rotary switch to (party mode).
blinks.
4In systems Anl 1.0, 1.9 and 3.5, the display reads 00:00 or indicates the remaining
time of party timer. Steps 2 and 3 can be skipped (selecting the control circuit).
2. Select the control circuit in which the day mode is to continue or be activated [q]:
Heating circuit 1
Heating circuit 2
DHW circuit
4Only those control circuits are available for selection which can be controlled by the
system (Anl) selected.
3. Confirm the control circuit [ ].
Display:
00:00 or indicates the remaining time of party timer.
4. Select how long the day mode is to continue running [q].
This setting is made in steps of 15 minutes.
5. Return the rotary switch to normal switch position (information level).
Note: The party timer counts down in steps of 15 minutes.
EB 5573 EN 13
Operation

1.8 Activating the extended information level
If the extended information level is activated, further information can be viewed after the listed
data points:
4Public holidays (can be changed, see section 1.8.1)
4Vacation periods (can be changed, see section 1.8.2)
4Valve positions
4Switching states of the binary inputs
4InFo 2: After confirming the level [ ] the following data appear in the sequence shown be-
low:
Controller ID
Memory capacity of data logging module (section 9.5)
255
Operating hours of solar circuit pump (refer to section 6.4)
Opening the extended information level:
1. Turn the rotary switch to (parameter and configuration level).
Display:
0 0 0 0 , blinks.
2. Set key number 1999 [q].
3. Confirm key number [ ].
Display:
0 0 0 0
4. Return the rotary switch to normal switch position (information level).
Note: The extended information level is deactivated when the key number 1999 is re-entered.
14 EB 5573 EN
Operation

1.8.1 Setting public holidays
On public holidays, the times-of-use specified for Sunday apply.
A maximum of 20 public holidays may be entered.
Parameter WE Level / Range of values
Public holidays –Extended information level/ 01.01 to 31.12
Proceed as follows:
1. In the extended information level (normal switch
position ) select data point for public holidays [q].
Display:
2. Open data point for public holidays.
3. If applicable, select
– – – – .
4. Activate editing mode for public holiday [ ].
and blink.
5. Select public holiday [q].
6. Confirm public holiday [ ].
To enter additional public holidays, re-select – – . – – and repeat the steps 4 to 6.
Note: Public holidays can also be set in PA5 parameter level (–> section 2.3).
Deleting a public holiday:
1. Under data point for public holidays, select the holiday you wish to delete [q].
2. Confirm selection [ ].
3. Select – –.– – [q].
4. Confirm selection [ ].
The public holiday is deleted.
Note: Public holidays that are not assigned to a specific date should be deleted by the end of the
year so that they are not carried on into the following year.
EB 5573 EN 15
Operation

1.8.2 Setting vacation periods
During vacation periods, the controller constantly remains in reduced operation. A maximum of
10 vacation periods can be entered. Each vacation period can be separately assigned to the
heating circuits Rk1, Rk2 and/or the DHW circuit.
Parameter WE Level / Range of values
Vacation period (START, STOP) –Extended information level / 01.01 to 31.12
Proceed as follows:
1. In the extended information level (normal switch
position ) select data point for vacation periods [q].
Display:
2. Open data point for vacation periods [ ].
Display:
START
3. If applicable, select – – – – [q].
4. Activate editing mode for start date of vacation period
[].
and blink.
5. Edit start date of vacation period [q].
6. Confirm start date of the vacation period.
Display:
STOP, – –.– –
7. Edit end of vacation period [q].
8. Confirm end of vacation period [ ].
The black square at the top of the display indicate the
assignment of the vacation periods to the individual
control circuits.
9. Select the control circuit to which the current vacation
period should apply [q].
Current vacation period applies to heating circuit 1
Current vacation period applies to heating circuit 2
–
Current vacation period applies to DHW circuit
The vacation period can be assigned to a single con-
trol circuit or any combination of all three circuits
(Rk1, Rk2, DHW circuit).
To enter additional vacation periods, re-select
– –.– – and repeat the steps 4 to 9.
16 EB 5573 EN
Operation

Note: Vacation periods can also be set in PA5 parameter level (–> section 2.3).
Deleting vacation periods:
1. Under data point for vacation periods, select the start date of the period you wish to de-
lete [q].
2. Confirm selection [ ].
3. Select
– –.– – [q].
4. Confirm selection [ ].
The vacation period is deleted.
Note: Vacation periods should be deleted by the end of the year so that they are not carried on
into the following year.
EB 5573 EN 17
Operation

1.9 Entering day and night set points
The desired room temperature for the day ( Day set point ) and a reduced room temperature for
the night (
Night set point ) can be entered in the controller for the heating circuits.
In the DHW circuit, the temperature you wish the DHW to be heated to can be set.
Switch position
Parameters WE Range of values
Day set point Rk1, Rk2 20 °C 0 to 40 °C
DHW temperature set point 55 °C Min. to max. DHW temperature
Switch position
Parameters WE Range of values
Night set point Rk1, Rk2 20 °C 0 to 40 °C
DHW sustained temperature 40 °C Min. to max. DHW temperature
Proceed as follows:
1. Turn the rotary switch to the required data point:
for Day set point or DHW temperature set point
for Night set point or DHW sustained temperature
blinks.
4In systems Anl 1.0, 1.9 and 3.5, the current set point is directly indicated. Skip the
following steps 2 and 3 (selecting the control circuit).
2. Select the control circuit for which the set point is to be entered [q]:
Heating circuit 1
Heating circuit 2
DHW circuit
4Only those control circuits are available for selection which can be controlled by the
system (Anl) selected.
3. Confirm the control circuit [ ].
Display: current set point
4. Adjust set point [q].
5. Return the rotary switch to normal switch position (information level).
18 EB 5573 EN
Operation

EB 5573 EN 19
Operation
q
Configuration and
parameter level
(start-up, see section 2)
PA4
PA5
CO1CO2
PA2Anl
q
Information level
CO4CO5
& key number
End PA1
PA1/CO1: Rk1 (heating circuit 1)
PA2/CO2: Rk2 (heating circuit 2)
PA4/CO4: DHW circuit
PA5/CO5: System-wide parameters
PA6/CO6 Modbus communication
Anl: System code number
PA6CO6
Fig. 2 · Level structure of TROVIS 5573

2 Start-up
The modifications of the controller configuration and parameter settings described in this sec-
tion can only be performed after the valid key number has been entered.
The valid key number for initial start-up can be found on page 123. To avoid unauthorized use
of the key number, remove the page or make the key number unreadable. In addition, it is pos-
sible to enter a new, customized key number (–> section 7.15).
2.1 Setting the system code number
21 different hydraulic schematics are available. Each system configuration is represented by a
system code number. The different schematics are dealt with in section 4. Available controller
functions are described in sections 5, 6 and 7.
Changing the system code number resets previously adjusted function blocks to their default set-
tings (WE). Function block parameters and parameter level settings remain unchanged.
The system code number is set in the configuration and parameter level.
Proceed as follows:
1. Turn the rotary switch to (configuration and parameter level).
Display:
0 0 0 0
2. Set valid key number [q].
3. Confirm key number [ ].
Display:
PA_
4. Select Anl .
5. Activate editing mode for the system code number [ ].
blinks.
6. Edit system code number [q].
7. Confirm system code number [ ].
Display:
End
8. Return the rotary switch to normal switch position (information level).
20 EB 5573 EN
Start-up