Samsung MWR-TH00 User manual

E S F I P A DB98-15770A(3)
DGR
Wired Remote Controller
MWR-TH00
MWR-TH01
INSTALLATION MANUAL
MANUAL DE INSTALACIÓN
MANUEL D’INSTALLATION
MANUALE D’INSTALLZIONE
MANUAL DE INSTALAÇÃO
INSTALLATIONS-HANDBUCH
E°XEIPI¢IO E°KATA™TA™H™
àçëíêìäñàü èé ìëíÄçéÇäÖ
System Air Conditioner
Aire acondicionado sistemático
Climatiseur numérique multifonctionnel
Sistema Aria Condizionata
Sistema Ar Condicionado
Klimaanlage System
™‡ÛÙËÌ· ∫ÏÈÌ·ÙÈÛÌÔ‡
ëËÒÚÂÏÌ˚È ÇÓÁ‰Û¯Ì˚È äÓ̉ˈËÓÌÂ
ENGLISH
ESPAÑOL
FRANÇAIS
ITALIANO
PORTUGUÊS
DEUTSCH
E§§HNIKA
RUSSIAN
MWR-TH00 IM_E_15770 3/9/06 2:06 PM Page 35

E-2
Safety Precautions
◆Read carefully this installation manual before
installation and check whether the remote controller
is installed correctly after installation.
◆Do not attempt to install or repair this wired remote
controller by yourself.
◆This remote controller contains no user-serviceable
parts. Always consult authorized service personnel
for repairs.
◆When moving, consult authorized service personnel
for disconnection and installation of the remote
controller.
◆Ensure that the wall is strong enough to support the
weight of the remote controller.
◆Must install the remote controller with rated power
supply.
◆The remote controller must be installed according to
the national electrical rules by an installation specialist.
◆When you want to disuse the remote controller,
consult authorized installation center.
WARNING
CAUTION
◆Do not use inflammable gases near the remote
controller.
◆Do not install the remote controller in a location where
it will come into contact with the combustible gases,
machine oil, sulphide gas, etc.
◆Avoid a location where acid/alkali solution or special
spray is used.
◆Choose a location that is dry and sunny, but not
exposed to direct sunlight. Available temperature is
between 0°C and 39°C.
◆Do not spill water into the wired remote controller.
◆Do not give tensile strength to the cable to avoid
disconnection.
◆Do not press buttons with a pointed thing.
◆Do not connect the power cable to the control terminal.
◆If the remote controller is installed in a hospital or other
special places, it should not affect other electronic
devices.
This installation manual indicates you to install the wired remote controller
which is connected to the indoor unit. For installation of other optional
accessories, see an appropriate installation manual.

E-3
ENGLISH
Contents
◆ W IRED REMOTE CONTROLLER AND ACCESSORIES . . . . . . . 4
◆ D IVIDING THE COM1/COM2
■ Flowchart for dividing COM1/COM2 . . . . . . . . . . . . . . . . . . . . . . 5
■ The Diagram of COM1/COM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
II
II
NN
NNSS SSTT TTAA AALL LLLL LLII IINN NNGG GG TT TTOO OO CC CCOO OOMM MM11 11(( ((FF FF11 11,, ,, FF FF22 22)) ))
◆ I NSTALLING THE COMMUNICATION CABLE
■ Installing the Communication cable . . . . . . . . . . . . . . . . . . . . . . 7
■ Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
■ Setting up indoor unit PCB and Wired Remote
Controller Option Switches
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
■ Examples of installing Wired Remote Controller . . . . . . . . . . . .10
■ The errors indicated on the Wired Remote Controller . . . . . . . .12
II
II
NN
NNSS SSTT TTAA AALL LLLL LLII IINN NNGG GG TT TTOO OO CC CCOO OOMM MM22 22(( ((FF FF33 33,, ,, FF FF44 44)) ))
◆ I NSTALLING THE COMMUNICATION CABLE
■ Installing the Communication cable . . . . . . . . . . . . . . . . . . . . . .13
■ Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
■ Setting up indoor unit PCB and Wired Remote
Controller Option Switches
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
■ The errors indicated on the Wired RemoteController . . . . . . . .16
■ Examples of installing Wired Remote Controller . . . . . . . . . . . .17
■ The errors indicated on the GHP Wired Remote Controller . . .21
◆ A DDITIONAL FUNCTION OF THE WIRED REMOTE CONTROLLER
■ Assigning the indoor unit RMC with the
Wired Remote Controller
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
■ Canceling the indoor unit RMC assigned with the
Wired Remote Controller
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

E-4
Wired Remote Controller and Accessories
Adjust K1 DIP switch(SW03) on the PCB to the “OFF”
position.
1
Accessories
Cable-tie (2) Cable clamp (5) M4x16 tapped
screw (7) Indoor Unit Power Drawing
Cable (1)
Communication
cable of the wired
remote controller (1)
CC
CCAA AAUU UUTT TTII IIOO OONN NN
◆ The wired remote controller must be installed by an
installation specialist.
◆ Before installing the wired remote controller, check
that you have turned off the main power.
◆ All cables should be installed according to the
national wiring rules and you must install it to the
wall not to be touched by users.
◆ Communication cable and power cable should be
installed separately.
(Connecting the power cable to communication
terminal will cause serious damage to the wired
remote controller. Please make sure that the power
cable is connected to the appropriate power terminal
to avoid serious damage.)
Wire joint (1) User’s
manual (1)
The following accessories are supplied with the air conditioner.
➢
The number of each accessory is indicated in parentheses.

ENGLISH
E-5
Dividing the COM1/COM2
Yes
No
Does the
indoor unit
support COM2(F3, F4)?
(Refer to the indoor unit
user's manual.)
Install the wired remote controller to
COM1. (Assign the DS01 switch of
the PCB of the wired remote
controller to SW2 ON.)
Install the wired remote controller to
COM2. (Assign the DS01 switch of
the PCB of the wired remote
controller to SW2 OFF.)
Flowchart for dividing COM1/COM2
PCB of the indoor unit Wired remote controller PCB
K1 : Adjust to OFF position.
S/W NO
SW2
Switch ON
COM1
(F1, F2)
Switch OFF
COM2
(F3, F4)

Dividing the COM1/COM2 (cont.)
E-6
The Diagram of COM1/COM2
COM1 Diagram
MAIN RMC MAIN RMC MAIN RMC
DVM Outdoor unit
COM1(F1, F2)
Group control
Wired remote controller
Indoor unit
COM2 Diagram
DVM PLUS Outdoor unit
COM1(F1, F2)
COM2(F3, F4) COM2(F3, F4)
Group control
Wired remote controller
Indoor unit

E-7
ENGLISH
Installing the Communication cable
◆I n case of 1-way cassette, connect the terminal BLOCK of the opening part of the
indoor unit with the main PCB of indoor unit using the indoor unit power drawing
cable as shown in the picture.
◆ The wired remote controller power cable is installed in all air conditioners except
1-way cassette
.
AC Power supply Don’t confuse the color.
Red
Blue
White
Black
Red
Blue
White
Black
Power cable of the wired
remote controller
Communication cable of the
wired remote controller
COM1(F1, F2) Red2P(2.5 pitch) Red2P
(2.5 pitch)
Indoor
unit PCB
White2P(2.5 pitch) White2P
(2.5 pitch)
Installing to COM1(F1, F2)

Installing to COM1(F1, F2) (cont.)
E-8
Installation
Open the wired remote controller by using 2 grooves on its
top.
1
Secure the rear cover of the wired remote controller on the
wall with 2 screws.
2
Reassemble the wired remote controller.
5
Connect each F1, F2, V1, V2, indoor unit terminal with
the wired remote controller terminal F1, F2, V1, V2.
3
After checking the kind of outdoor unit, assign the DS01
switch SW2 of the indoor unit PCB to ON.
4
◆ If you set to COM2 and install it to COM1, ‘606’ of
error signs is displayed on the wired remote
controller.
DS01
SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8
DS02
SW1
SW2
SW3
SW4
SW5
Cooling Only
COM2(F3, F4)
°C
The wired and
wireless remote
controller available
Cooling and Heating
COM1(F1, F2)
°F
Can be used
wired remote controller
only
Switch
No. Switch OFF Switch ON
Refer to the chapter ‘Additional Function of the wired
remote controller’.
◆ When connecting the communication cable and
the power cable, don’t confuse about each cable.
If the cables are connected improperly, the wired
remote controller will not work.

E-9
ENGLISH
Setting up indoor unit PCB and Wired
Remote Controller Option switches
Indoor unit PCB
Wired remote controller PCB
◆ If you control the indoor unit with the wired remote
controller, adjust K1 of SW4 option switch of the
indoor unit PCB to ‘OFF’.
◆ If you install the indoor unit as shown in the picture,
can control it with the wired remote controller.
ADDRESS of the wired remote controller and RMC
ADDRESS of the indoor unit should be assigned as
the same.
◆ Therefore as the RMC ADDRESS is adjusted to
‘0’in the picture, the indoor unit is controlled by
the wired remote controller which is adjusted to ‘0’.
◆ Assign the RMC ADDRESS of the wired remote
controller same as the indoor unit to be controlled.
DS03
SW4
ADDRESS Switch
Indoor unit MAIN PCB switch
RMC

E-10
Installing to COM1(F1, F2) (cont.)
MAIN
ADDRESS RCM ADDRESS
SW4
MAIN RMC MAIN RMC MAIN RMC
DVM Outdoor unit
Wired remote controller
Indoor unit PCB
Indoor unit
Individual control : Individual control of 3 indoor units with 3 wired remote controller.
Examples of installing Wired Remote Controller