Samsung MRK-A00 User manual

ENGLISH
Receiver & Display Unit
INSTALLATION MANUAL
MANUAL DE INSTALACIÓN
MANUEL D’INSTALLATION
MANUALE D’INSTALLZIONE
MANUAL DE INSTALAÇÃO
INSTALLATIONS-HANDBUCH
E°XEIPI¢IO E°KATA™TA™H™
àçëíêìäñàü èé ìëíÄçéÇäÖ
ESPAÑOL
FRANÇAIS
ITALIANO
PORTUGUÊS
DEUTSCH
E§§HNIKA
RUSSIAN
System Air Conditioner
Aire acondicionado sistemático
Climatiseur numérique multifonctionnel
Sistema Aria Condizionata
Sistema Ar Condicionado
Klimaanlage System
™‡ÛÙËÌ· ∫ÏÈÌ·ÙÈÛÌÔ‡
ëËÒÚÂÏÌ˚ ÇÓÁ‰Û¯Ì˚ äÓ̉ˈËÓÌÂ
E S F I P D G R A DB98-05186A(2)
MRK-A00, A00U
MRK-B00, B00U
MRK-B01, B01U

Safety Precautions
◆Read carefully this installation manual before
installation and check whether the receiver & display
unit is installed correctly after installation.
◆Do not attempt to install or repair this receiver &
display unit by yourself.
◆This receiver & display unit contains no user-
serviceable parts. Always consult authorized service
personnel for repairs.
◆When moving, consult authorized service personnel
for disconnection and installation of the receiver &
display unit.
◆Ensure that the wall is strong enough to support the
weight of the receiver & display unit.
◆Must install the receiver & display unit with the wire
kit which is supplied with the unit.
◆The receiver & display unit must be installed
according to the national electrical rules by an
installation specialist.
◆When you want to disuse the receiver & display unit,
consult authorized installation center.
WARNING
E-2
This installation manual indicates you to install the receiver & display unit which
is supplied with the wireless remote controller of duct type air conditioner. For
installation of other optional accessories, see an appropriate installation manual.

CAUTION ◆
Do not use inflammable gases near the receiver &
display unit.
◆ Do not install the receiver & display unit in a location
where it will come into contact with the combustible
gases, machine oil, sulphide gas, etc.
◆ Avoid a location where acid/alkali solution or special
spray is used.
◆ Choose a location that is dry and sunny, but not
exposed to direct sunlight. Available temperature is
between 0°C(32°F) and 39°C(102°F).
◆ Do not spill water into the receiver & display unit.
◆ Do not give tensile strength to the cable to avoid
disconnection.
◆ Do not press buttons with a pointed thing.
◆ If the receiver & display unit is installed in a hospital
or other special places, it should not affect other
electronic devices.
E-3
ENGLISH

Receiver & Display Unit Installation - Concealed Type
E-4
Accessories MRK-A00, A00U
Receiver &
display unit (1)
STS 2S-2x10
tapped screw (4)
2S-4x12 tapped
screw (2)
Owner’s
instructions(1) Installation manual (1)
Wire kit
(Length:10m)
Remove the receiver & display unit cover by using the
tab on its bottom.
1
Open the receiver & display unit.
2
Connect the end of the connector wire to the receiver
& display unit and connect the other end of the wire to
the MAIN PCB (CN91) as shown in figure.
3
CC
CCAA AAUU UUTT TTII IIOO OONN NN
Do NOT keep the receiver & display unit cable
with a 220V cable because the remote controller
cables have low voltage.
◆
Receiver &
display unit

E-5
ENGLISH
Secure the receiver & display unit on the wall with
two screws.
4
Reassemble the receiver & display unit cover.
5
CC
CCAA AAUU UUTT TTII IIOO OONN NN
◆ The receiver & display unit must be installed by an
installation specialist.
◆ Before installing the receiver & display unit, ensure
that you have turned off the main power.
◆ All receiver & display unit cables should be installed
according to the national wiring rules and you must
install it in the wall not to be touched by users.

Receiver & Display Unit Installation - Standard Type
Accessories MRK-B00, B00U, B01, B01U
Receiver &
display unit (1)
Cable-tie (2) Cable clamp
(5)
M4 X 16 tapped
screw (7)
Owner’s
instructions(1) Installation manual (1) Wire Kit (Length:10m)
E-6
Remove the receiver & display unit cover by using the
tab on its bottom.
1
Open the receiver & display unit.
2
Connect the end of the connector wire to the receiver
& display unit and connect the other end of the wire to
the MAIN PCB (CN91) as shown in figure.
3
CC
CCAA AAUU UUTT TTII IIOO OONN NN
Do NOT keep the receiver & display unit cable
with a 220V cable because the remote controller
cables have low voltage.
◆
Receiver &
display unit

E-7
ENGLISH
Close the receiver & display unit.
4
Secure the receiver & display unit on the wall with two
screws.
5
Reassemble the receiver & display unit cover.
6
CC
CCAA AAUU UUTT TTII IIOO OONN NN
◆ The receiver & display unit must be installed by an
installation specialist.
◆ Before installing the receiver & display unit, ensure
that you have turned off the main power.
◆ All receiver & display unit cables should be installed
according to the national wiring rules and you must
install it in the wall not to be touched by users.

ELECTRONICS
THIS AIR CONDITIONER IS MANUFACTURED BY:
ESTE AIRE ACONDICIONADO HA SIDO FABRICADO POR:
CE CLIMATISEUR EST FABRIQUE PAR:
QUESTO CONDIZIONATORE D’ARIA È PRODOTTO DA:
ESTE APARELHO DE AR CONDICIONADO É FABRICADO POR:
DIESE KLIMAANLAGE IST FABRIZIERT VON:
AYTH H ™Y™KEYH KATA™KEYA™THKE A¶O:
ùíéí äéçÑàñàéçÖê àáÉéíéÇãÖç îàêåéâ:
Printed in Korea