Samsung MCM-A100 User manual

ENGLISH
ENGLISHESPAÑOLFRANÇAISITALIANOPORTUGUÊSDEUTSCH
USER’S MANUAL
Function Controller
MCM-A100
System Air Conditioner
DB98-27317A(1)SE F I DP G R A
EΛΛHNIKARUSSIAN
MCM-A100_IB_E_27317.indd 17 2007-01-31 ｿﾀﾀ・10:26:56

E-2
Safety Precautions
• Before using the function controller, read carefully this instructions.
• After reading the instructions, keep this user’s manuals and the installation manual in a
handy and safe place. If a user is changed, you must hand over the manuals.
• Never attempt to install the air conditioning system or to move the function controller
by yourself.
WARNING
 Do not attempt to install or repair this function controller
by yourself.
 This function controller contains no user-serviceable parts.
Always consult authorized service personnel for repairs.
 When moving, consult authorized service personnel for
disconnection and installation of the function controller.
 Ensure that the wall is strong enough to support the
weight of the function controller.
 Must install the function controller with rated power
supply.
 In the event of a malfunction (burning smell, etc.),
immediately stop operation, turn off the electrical breaker,
and consult authorized service personnel.
CAUTION
 Do not use inflammable gases near the function
controller.
 Do not spill water into the function controller.
 Do not operate the function controller with wet hands.
 Do not install the function controller in a location where
it will come into contact with the combustible gases,
machine oil, sulphide gas, etc.
 Do not press buttons with a pointed thing.
 Do not pull or bend the function controller cable
excessively.
 Do not use this function controller for other purpose.
 Do not spray an insecticide or other combustible things
on the function controller.
 Do not clean the function controller with benzene,
solvents or other chemicals.
 Do not give a shock to the function controller or
disassemble it by yourself.
MCM-A100_IB_E_27317.indd 2 2007-01-31 ｿﾀﾀ・10:26:56

E-3
ENGLISH
Contents
 VIEW OF THE FUNCTION CONTROLLER ............................................ 4
 GETTING START ................................................................................. 5
 SELECTING THE INDOOR UNIT .......................................................... 6
 SELECTING THE AUTOMATIC OPERATING MODE ........................... 7
 COOLING YOUR ROOM ..................................................................... 8
 HEATING YOUR ROOM( EXCEPT COOLING ONLY MODELS ) ........... 10
 REMOVING EXCESS HUMIDITY ........................................................ 12
 AIRING YOUR ROOM ....................................................................... 14
 ADJUSTING THE AIR FLOW DIRECTION( EXCEPT DUCT TYPE ) ....... 15
MCM-A100_IB_E_27317.indd 3 2007-01-31 ｿﾀﾀ・10:26:56

E-4
Getting Started
You have just purchased a function controller and it has been installed by your
installation specialist.
Your user’s manual contains much valuable information on using your function
controller. Please take time to read as it will help you take full advantage of
the unit’s features.
In the main part of the document, you will find a series of step-by-step
procedures for each function available.
The illustrations in the step-by-step procedures use three different symbols:
PRESS PUSH HOLD DOWN
View of the Function Controller
The function controller is an additional controller which is used with the centralized controller.
Swing button
(Except Duct Type)
Filter Sign indicator
Mode selection button
Communication error
indicator
Room number display
Test indicator
Indoor unit selection button
Test button Filter Reset button
Temperature adjustment
buttons
Removing frost indicator
(Except Cooling Only Models)
Temperature setting
Fan speed
Air flow direction
On/Off & Timer
Set/Cancel button
Fan speed adjustment
button
On/Off indicator
Operating mode
Centralized controller indicator
Note 
Test button is for your installation specialist. You must NOT press it.

After cleaning the air filter, press the filter reset button. Then the function
controller will display the FILTER SIGN indicator when the time to clean the
air filter.

Duct type air conditioner does not have function of adjusting air flow
direction. Therefore, the function is not operated even if you press the swing
button.
MCM-A100_IB_E_27317.indd 4 2007-01-31 ｿﾀﾀ・10:26:57

E-5
ENGLISH
Getting Started
You have just purchased a function controller and it has been installed by your
installation specialist.
Your user’s manual contains much valuable information on using your function
controller. Please take time to read as it will help you take full advantage of
the unit’s features.
In the main part of the document, you will find a series of step-by-step
procedures for each function available.
The illustrations in the step-by-step procedures use three different symbols:
PRESS PUSH HOLD DOWN
MCM-A100_IB_E_27317.indd 5 2007-01-31 ｿﾀﾀ・10:26:58

E-6
1Select an indoor unit you want to control by pressing
button.
Result:  Each time you press button, the room
number is increased by 1, and each time you
press
button, the room number is decreased
by 1 from 0~15.
2Turn the air conditioner on by pressing
(ON/OFF) button.
Result:  The On/Off indicator on the function controller
comes on.
 The air conditioner runs in the mode selected
when the unit was last used.
3Select an appropriate operating mode by pressing Mode
button.
Result:
The air conditioner runs in the selected mode.
Note For further details on operating modes, refer to
page 7~15.
Selecting the Indoor Unit
You can control a specific indoor unit from the function controller.
MCM-A100_IB_E_27317.indd 6 2007-01-31 ｿﾀﾀ・10:26:58

E-7
ENGLISH
Selecting the Automatic Operating Mode
In the Automatic mode, the room temperature and the fan speed
are controlled automatically.
1If necessary, press
(ON/OFF) button.
Result:  The On/Off indicator on the function controller
comes on.
 The air conditioner runs in the mode selected
when the unit was last used.
Caution The air conditioner is fitted with a protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
lt will start up normally after three minutes.
2To select the AUTO mode, press the Mode button until
is
displayed at the top of the function controller.
Result: The air conditioner runs in AUTO mode.
Note You can change modes at any time.
3To adjust the temperature, press the Temperature buttons
one or more times until the required temperature is displayed.
Possible temperatures are between 18°C(65°F) and 30°C(86°F)
inclusive.
Result: 
Each time you press Temperature buttons:
- The temperature is adjusted by 1°C(1°F).
 The air conditioner starts cooling, provided
that the room temperature is than the selected
temperature.
- The quantity of air is adjusted automatically.
MCM-A100_IB_E_27317.indd 7 2007-01-31 ｿﾀﾀ・10:27:00

E-8
Cooling Your Room
You must select the COOL mode if you wish to adjust the :
 Cooling temperature
 Fan speed when cooling
1If necessary, press
(ON/OFF) button.
Result:  The On/Off indicator on the function controller
comes on.
 The air conditioner runs in the mode selected
when the unit was last used.
Caution The air conditioner is fitted with a protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
lt will start up normally after three minutes.
2To select the COOL mode, press the Mode button until
is
displayed at the top of the function controller.
Result: The air conditioner runs in COOL mode.
Note You can change modes at any time.
MCM-A100_IB_E_27317.indd 8 2007-01-31 ｿﾀﾀ・10:27:02

E-9
ENGLISH
Cooling Your Room
3To adjust the temperature, press the Temperature buttons
one or more times until the required temperature is displayed.
Possible temperatures are between 18°C(65°F) and 30°C(86°F)
inclusive.
Result: 
Each time you press Temperature buttons:
- The temperature is adjusted by 1°C(1°F).
 The air conditioner starts cooling, provided that
the room temperature is higher than the
selected temperature ; the fan will, however,
operate.
4Select the fan speed by pressing the Fan button one or more
times until the intended value is displayed :
Automatic(rotated :   )
Low
Medium
High
5To control the direction of the air flow, refer to page 15.
MCM-A100_IB_E_27317.indd 9 2007-01-31 ｿﾀﾀ・10:27:03

E-10
Heating Your Room (Except Cooling Only Models)
You must select the HEAT mode if you wish to adjust the :
 Heating temperature
 Fan speed when heating
1If necessary, press
(ON/OFF) button.
Result:  The On/Off indicator on the function controller
comes on.
 The air conditioner runs in the mode selected
when the unit was last used.
Caution The air conditioner is fitted with a protection
mechanism to prevent the unit from being damaged
when it is started immediately after being:
 Plugged in
 Stopped
lt will start up normally after three minutes.
2To select the HEAT mode, press the Mode button until
is
displayed at the top of the function controller.
Result: The air conditioner runs in HEAT mode.
Note You can change modes at any time.
You can select the HEAT mode only in heat pump models.
MCM-A100_IB_E_27317.indd 10 2007-01-31 ｿﾀﾀ・10:27:04