Samsung SCC-3000 User manual

Thank you for buying a Samsung SYSTEM CONTROLLER.
This manual will guide you through using the SYSTEM CONTROLLER. Please read this manual carefully
before using the SYSTEM CONTROLLER.

《2》
Contents
●Important Safety Instructions 3
●Major Functions and Features
(1) Overview 5
(2) Features 5
●Product Components 5
●System Overview 6
●Names and Functions of Each Part
(1) Camera Setup Section 7
(2) Number Pad 8
(3) External Device Selectors 8
(4) Universal Controller 9
(5) DVR Controller 9
(6) Camera Controller 11
(7) Junction Box 11
●Before Operation
(1) Power-On 12
(2) Initial Screen Display 12
(3) Camera ID Setup 12
(4) Joystick/Camera Control Button 13
(5) Camera Movement Speed Control 14
(6) Camera Zoom Control 14
(7) Camera Focus Control 14
●PTZ Mode
(1) PTZ Setup Mode 15
(2) PRESET 16
(2-1) PRESET Setup 16
(2-2) PRESET Movement 16
(3) SWING 17
(3-1) SWING Setup 17
(3-2) SWING Operation 17
(4) GROUP 18
(4-1) GROUP Setup 18
(4-2) GROUP Operation 18
(5) TOUR 19
(5-1) TOUR Setup 19
(5-2) TOUR Operation 19
(6) MODEL 21
(7) TRACE 22
(7-1) TRACE Memory 22
(7-2) TRACE Operation 23
(8) AF 23
(9) OSD 24
●DVR Mode 25
●Controller Mode
(1) Controller Setup Mode 26
(2) Controller ID Setup 27
(3) SERIAL Setup 27
(4) DATA COPY 28
(5) RESPONSE 29
(6) PASSWORD 31
(6-1) PASSWORD Setup 31
(6-2) Applying Password-Setup Mode 32
(6-3) Applying Password-Power 32
(6-4) Entering Password 32
(7) PRIORITY 33
(8) DEFAULT 34
●REFERENCE
(1) Swing, Group Movement Speed 35
(2) System Connections 36
(2-1) Connecting Controller and Junction Box 36
(2-2) Connecting Junction Box and
External Devices 36
(3) RS-485/422 Pin Layout (D_SUB_FEMALE) ........37
(4) RS-232C Pin Layout (D_SUB_MALE) 37
(5) Controller Specifications 38
(6) RS-485/422 Specifications 38
(7) Junction Box DIP Switch 38

《3》
Important Safety Instructions
■ All work related to the installation of this appliance must be performed by qualified service personnel or system installers.
- If the product is connected or installed improperly, electric shock, fire, severe injury, and/or damage can result.
■Please install the product on a completely flat floor.
- Always check the strength and stability of the installation location.
- Do not drop the appliance on the floor. This may result in damage or injury.
■Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers.
- There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.
■Never use the appliance in places where there are flammable materials.
- Never use the appliance in places where flammable materials such as gas are used.
This may result in fire, explosion, and other serious accidents.
■Never touch un-insulated parts with wet hands.
- Touching un-insulated parts with wet hands may result in serious electric shock.
■Never expose the appliance to water or moisture.
- If the appliance gets wet, immediately turn the power off.
- Stop using the appliance if it gets wet. Contact the manufacturer immediately.
■Stop using the appliance if there appears to be any operational problem.
- Immediately turn the power off to the appliance if there is any abnormal condition such as smoke or unusual smells.
- Continuing to use the appliance under abnormal conditions may result in serious damage.
■Always use the recommended power.
- Using incorrect power source ratings may result in fire, electric shock, or damage.
■Always handle the connection cable with care.
- Never damage or modify the connection cable.
- Do not pull, expose to heat, or place heavy objects on the connection cable.
- Non-observance of these warnings may result in fire, electric shock or damage.
Warning
■Use the appliance indoors only.
- Do not place the appliance outdoors or expose it to rain or moisture.
- If dropped in water, the appliance may be corroded and damaged.
■Do not use the appliance where there is excessive dust, smoke, or moisture.
- Using the appliance under such conditions may result in fire, electric shock or serious damage.
■Do not operate the appliance in temperatures beyond those specified.
- Excessive heat or cold may damage the appliance.
- Always operate the appliance within the recommended temperature range of 0˚C ~ 40˚C.
■Do not place the appliance in direct sunlight.
- This may discolor the appliance.
■Do not apply excessive shock to the appliance.
- Excessive shock may damage the appliance.
Caution

《4》
Important Safety Instructions
■If the controller body gets dirty, turn the power off and wipe the surface with a soft cloth.
- Do not use chemical agents such as alcohol or benzene.
■For detailed information on upgrading the firmware, please direct your inquiries to the installation vendor.
Maintenance and Repair
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area
is likely to cause harmful interference, in which
case the user will be required to correct the
interference at his own expense.
Refer all work related to the installation of this
appliance to qualified service personnel or
system installers.

《5》
Major Functions and Features
(1) Overview
This product is designed for use only with the Speed Dome camera, CCTV receiver, and Samsung Digital Video Recorder.
●Speed Dome camera : Samsung Techwin (SPD-1600/2200/2500), PELCO-D, PANASONIC (WV-CS854A),
SAMSUNG ELECTRONICS (SCC-643-641)
●CCTV Receiver : SRX-100B
●DVR : Samsung Techwin (SVR-1630/1620/430)
(2) Features
- It is possible to totally control the 255 Speed Dome camera, CCTV Receiver and Samsung Digital Video Recorder.
- If the Speed Dome is set to one-way reception (RESPONSE OFF), it is possible to connect a maximum of 16 sub-
controllers, including the master controller.
- If the Speed Dome is set to two-way reception (RESPONSE ON), it is possible to connect a maximum of 12 sub-
controllers, including the master controller.
- Camera control with the joystick, zoom buttons, and focus buttons
- Easy camera preset location setup and movement
- Camera control without an operator through automatic operation mode
※Different surveillance cameras may have different names for the same functions, depending on the
manufacturer.Some functions may not be available for certain models.
※If the Speed Dome (SPD-1600/2200/2500) DIP switch is set to one-way reception, each sub-controller can be
controlled independently. If it is set to two-way reception, sub-controllers cannot be controlled independently.
※The SPD-1600/2500 is set to two-way reception and the SPD-2200 is set to one-way reception by factory default.
※Sub-controllers cannot be controlled if the master controller is in use.
●SCC-3000 Controller ●Junction Box
●Controller Connection Cable
Product Components
●Power Adaptor (DC 12V) ●User's Manual

《6》
System Overview
※Please refer to page 39 for the detailed connection map of the JUNCTION Box, Controllers and external devices.
(1) General Connection
: Controller Connection Cable
: RS-485/422
: Video Cable
DVR
Dome Camera + DVR: 255 max.
Dome Camera
Dome Camera
Dome Camera
SVR-1630: 255 max.
CCD Camera
Remarks
Junction Box

《7》
Names and Functions of Each Part
(1) Camera Setup Section
①RESET : Resets camera power.
②PRESET : Moves camera to the preset location (see p.16).
③LIGHT : Toggles the lights around the camera on and off.
④AUX : Toggles the camera’s external case AUX on and off.
⑤TOUR : Sets more than 1 group for tour and performs continuous group action (see p.19).
⑥SALVO : Not used; will be applied to F/W in the future.
⑦SWING : Continuously travels between two assigned locations horizontally (pan) or
vertically (tilt) (see p.17).
⑧GROUP : Repeats sequential surveillance of assigned preset locations with preset
movement rates and intervals (see p.18).
⑨AF : Sets the focus to automatic or manual after operating the camera (see p.23).
⑩OSD : Displays the camera OSD menu (see p. 24).
⑪FUNCTION : Used to perform 2 functions or more at the same time (see p.8).
※Some buttons in the camera setup section may not be supported or may be used differently depending on the
camera manufacturer. Please refer to the table below for the buttons supported by the major camera manufacturers.
SPD-1600 SPD-2200 SPD-2500 PELCO-D PANASONIC
(WV-CS854A)
SAMSUNG ELECTRONICS
(SCC-643/641)
Not used; will be applied to F/W in the future.
O(AUTO-PAN)
RESET O O O O O X
PRESET O O O O O O
TOUR O O O X X X
SALVO
SWING O O O X
GROUP O O O X O (AUTO-SEQ) O (SCAN)
AF O O O O O O
OSD O O O O O O
LIGHT Applies only to systems with housing and receivers that support the light function. (SRX-100B only)
AUX Applies only to systems with AUX terminals. (SRX-100B only)

《8》
Names and Functions of Each Part
(2) Number Pad
※'F' in the table below refers to the Function button.
①0 ~ 9 : Used for entering camera ID, channel number, monitor number, DVR ID, etc.
(see p.23).
②F + 0 : Activates the system setup menu (see p.24).
③▲/ ▼: Used for increasing or decreasing menu values in detailed setup menus.
※When using functions that are performed by a combination of the function button and
numeric keys, the setup may be different depending on the camera manufacturer.
Please refer to the table below for the setup for major camera manufacturers.
(3) External Device Selectors
①PTZ : Selects the PTZ mode (see p.15~24).
②DVR : Selects the DVR mode (see p.25).
③CAMERA : Enter camera number and press the CAMERA button to set the camera ID (PTZ mode) or set the channel
(DVR mode).
④MONITOR : Not used; will be applied to F/W in the future).
SPD-1600 SPD-2200 SPD-2500 PELCO-D PANASONIC
(WV-CS854A)
SAMSUNG ELECTRONICS
(SCC-643/641)
TRACE RUNF+1 TRACE RUN TRACE RUN TRACE RUN
(PATTERN)
TRACE RUN
(PATTERN)
TRACE RUN
(PATTERN 1)
TRACE
MEMORY
F+2 TRACE
MEMORY
TRACE
MEMORY - F2(SPECIAL 2) TRACE RUN (PATTERN 2)
TRACE
MEMORY STOP
F+3
TRACE
MEMORY STOP
TRACE
MEMORY STOP
- F3
TRACE RUN
(PATTERN 3)
F+4 AUTO
POWER ON
AUTO
POWER ON
AUTO
POWER ON - AUTO-SORT -
F+5 AUTO
POWER OFF
AUTO
POWER OFF
AUTO
POWER OFF - - -
※Use the AUTO POWER ON setting to allow the camera to resume the tasks in its memory upon power supply, even if
they were previously aborted as a result of power failure, etc.

《9》
Names and Functions of Each Part
(4) Universal Controller
①ZOOM W/T : Performs camera zoom action (wide and telephoto).
②FOCUS -/+ : Used for manual focus adjustment.
③|| : Used for moving the menu cursor up (when menu is active), pausing DVR
playback, or playing stills.
④■: Used for moving the menu cursor down (when menu is active) or stopping
DVR playback.
⑤I▶: Used for moving the menu cursor left (when menu is active) or Slow Playback.
⑥▶▶: Used for moving the menu cursor right (when menu is active) or Fast Playback
⑦▶: Used for playing recorded video.
⑧REC / ESC : Used for starting surveillance screen recording, canceling entered
values, or moving to the previous stage.
⑨ ENTER / DIR : Used for executing the entered values, performing setups (PTZ mode
and DVR mode), or playing recorded video in the reverse direction.
(5) DVR Controller
※Please refer to the DVR product manual for the buttons without reference pages.
Some functions may not be supported by certain models.
①QUICK SET : The Quick Setup menu is displayed in the DVR monitor.
②STATUS : The current DVR status is displayed in the DVR monitor.
③SEARCH : Used for searching the DVR recording list.
④PLAY MODE : Used for recording and playing the DVR with the controller.
(SVR-900/1620 only)
⑤MENU : The DVR menu is displayed in the DVR monitor.
⑥MULTI : Used for switching the DVR monitor from single screen playback mode
to multiple screen playback mode.
⑦AUTO : displays the sequence of cameras connected to the DVR on the monitor.
⑧ALRAM RESET : Used for resetting the alarm and event display, turning the relay
on and off, and closing the event notification window.
⑨LIST : Shows the event list saved in the DVR storage device.
⑩PIP : Used for performing the PIP (Picture In Picture) function.
⑪DIGITAL ZOOM : Used for zooming in the monitor screen when in single screen
playback mode.
⑫FREEZE : Used for pausing the video when displaying a surveillance video.
⑬SPOT : Used to switch to spot monitor.
⑭COPY : Used for copying, backing up, or deleting saved video.
⑮LIVE / PLAY BACK : Used for toggling the surveillance screen and playback screen.
⑯RELAY : Used for manual control of replay output.
●It is possible to use all the functions except menu cursor movement of ③~ ⑨buttons in only PLAY MODE for
SVR-900/1620. When the user presses the PLAY MODE button of the controller, PLAY MODE is on.
When PLAY MODE is on, [P-MODE] appears on the LCD monitor. Press the PLAY MODE button once again
to release PLAY MODE.
INFORMATION

《10》
Names and Functions of Each Part
※Some DVR controller buttons may not be supported or may be used differently than as described in this manual,
depending on the DVR model. Please refer to the table below for the buttons supported by major DVR model
manufacturers. The DVR button with multiple functions works in the same way on the controller.
SVR-430 SVR-900 SVR-1620 SVR-1630
QUICK SET O - - -
STATUS O O O -
SEARCH O O O O
PLAY MODE - O O -
FOCUS - O O O O
FOCUS + O O O -
MENU O O O O
MULTI O O O O
AUTO O O O O
ALARM RESET O O O O
LIST - O O -
PIP O O O -
DIGITAL ZOOM O O O O
FREEZE - O O -
SPOT - O O O (A/B)
COPY O O O O
LIVE/PLAY BACK O Screen Selection Screen Selection -
RELAY - - - O
-/+ O O O -
II OO
Jog(PLAY MODE)
O
Jog(PLAY MODE)
O
Jog
▶▶ O
O
Fast Forwarding
(PLAY MODE)
O
Fast Forwarding
(PLAY MODE)
O
■O
O
Pause
(PLAY MODE)
O
Pause
(PLAY MODE)
O
I▶Jog
O
Slow Playback
(PLAY MODE)
O
Slow Playback
(PLAY MODE)
O
ENTER / DIR O
O
Direction Switching
(PLAY MODE)
O
Direction Switching
(PLAY MODE)
O
REC / ESC
O
Record function for
Surveillance (LIVE)
screen
O
Record function for
Surveillance (LIVE)
screen
O
Record function for
Surveillance (LIVE)
screen
O
Record function for
Surveillance (LIVE)
screen

《11》
Names and Functions of Each Part
(6) Camera Controller
①Joystick: Used for moving the camera up, down, left, and right, and for zoom control (see p.13).
1) Tilt up (Up button): Moves the camera up.
2) Tilt down (Down button): Moves the camera down.
3) Tilt left (Left button): Moves the camera left.
4) Tilt right (Right button): Moves the camera right.
5) Turn stick clockwise: Performs telephoto-zoom.
6) Turn stick counter-clockwise: Performs wide zoom.
②SLOW : Sets the camera movement (up, down, left, and right) speed slow.
③FAST : Sets the camera movement (up, down, left, and right) speed fast.
(7) Junction Box
[Joystick] [Camera Control Button]
Power Input
Connector Junction Box
Connector
[Front]
DIP Switch
PTZ/DVR
Connector Sub-Controller
Connector Reversed
Connector
[Back]

《12》
Before Operation
(1) Power-On
①Power on the connected external devices before turning the controller on.
②Press the power button at the back of the controller to power on the controller.
③The [SYSTEM Controller] message and F/W version will be displayed in the LCD
monitor, and the message will disappear when the controller is ready for use.
▤The [JOYSTICK ERROR] error will be displayed in the LCD monitor if the
joystick is not placed in the center during power-on.
(2) Initial Screen Display
①CAM ID : Shows the currently selected camera ID. Default is 1.
②SPD : Shows the currently selected camera model name.
Default is SPD.
③MONITOR : Not used; will be applied to F/W in the future.
④[- - -] : Shows the numbers (ID) entered when entering numbers
with the number pad.
⑤ID : Shows the current controller ID. If the ID is 1, it acts as the master
controller. If the ID is 2 or higher, it acts as a sub -controller.
Sub-controllers cannot be used independently without a master
controller.
▤Always assign a unique ID to ensure that the controller IDs do not
conflict with each other.
▤SPD : SPD-1600/ SPD-2200/ SPD-2500(Samsung Techwin Co., Ltd.)
PTZCONTROLSYSTEM
CAMID: 1SPD
MONITOR:1[---]
ID:1
(3) Camera ID Setup
①Enter a number using the number pad.
②The number entered will be shown in the [- - -] display.
③Press the CAMERA or ENTER button to set the camera ID with the
number entered.
▤Any number from 1 to 255 can be selected. If the number entered is
not within the selectable range, the last entered number is taken as
the first number.
PTZCONTROLSYSTEM
CAMID: 1SPD
MONITOR:1[5]
Enter:PTZIDSet
PTZCONTROLSYSTEM
CAMID: 5SPD
MONITOR:1[---]
ID:1
[ power button ]
①
③
②
④
⑤

《13》
Before Operation
(4) Joystick/Camera Control Button
■The joystick can be used to control the camera’s left and right (pan) and up and down (tilt) movements.
■The joystick can be used to control camera zoom functions.
[Camera wide zoom] [Camera telephoto zoom]

《14》
Before Operation
(5) Camera Movement Speed Control
■Use the joystick or press the Slow/Fast button at the bottom of the
camera control button section to adjust the camera movement speed.
▤You must press the ESC button after adjusting the camera
movement speed in order to be able to use other controller buttons.
▤The SLOW/FAST button can be used to adjust movement speed
for models without a joystick.
(6) Camera Zoom Control
■Press the ZOOM W/T button to control zoom wide and zoom telephoto.
ZOOM W : Zoom Wide
ZOOM T : Zoom Telephoto
(7) Camera Focus Control
■Press the FOCUS -/+ button to control camera focus.
FOCUS - : Focus gets nearer.
FOCUS + : Focus gets further.
▤The FOCUS -/+ button can be used as the ENTER/ESC button for
the SVR-1630 and SPD series.
[SLOW/FAST button]
[ZOOM W/T button]
[FOCUS -/+ button]

《15》
●The menu may be different depending on the PTZ camera model.
●Press the ESC button to move to an upper setup mode.
INFORMATION
PTZ Mode
(1) PTZ Setup Mode
■This menu is for setting up the PTZ camera function.
It is impossible to operate Speed Dome and DVR by sub-controllers
when the master controller is set to on.
①At the initial screen, press the Function button and press the 0 button
to activate the [SETUP SYSTEM] menu.
②Press the 1 button to activate the [PTZ SETUP 1 ▶] menu.
③Press the ▶▶ button to activate the [◀PTZ SETUP 2] menu.
SETUPSYSTEM
1:PTZ 2:DVR
3:CONTROLLER
PressNumericKey
PTZSETUP1
1:PRESET 2:SWING
3:GROUP 4:TOUR
PressNumericKey
PTZSETUP2
1:MODEL 2:TRACE
3:AF
PressNumericKey
Models supported
Models supported
Menu Menu
TOUR SPD series --
PRESET
SPD series, PELCO-D, PANASONIC,
SAMSUNG ELECTRONICS
MODEL
SPD series, PELCO-D, PANASONIC,
SAMSUNG ELECTRONICS
SWING SPD series TRACE SPD series, PELCO-D,
PANASONIC
GROUP SPD series AF
SPD series, PELCO-D, PANASONIC,
SAMSUNG ELECTRONICS

《16》
PTZ Mode
(2) PRESET
■This menu is for setting the camera to move to preset locations.
(2-1) PRESET Setup
①At the [PTZ SETUP 1 ▶] menu, press the 1 button (see p.15).
②Use the joystick or camera control button (SCC-3000 model) to move
the camera to the desired location (move up, down, left, and right, and
control zoom).
③Enter a preset number.
④Press the Enter button to assign the number to the current location.
(2-2) PRESET Movement
①In the initial screen, enter an assigned preset number.
②The selected number will be shown in the [- - -] display.
③Press the Preset button to move the camera to the preset location.
▤If the number entered is not within the selectable range, the last
entered number is taken as the first number.
The selectable range for each camera model is as follows.
●SPD 1600/2200/2500 : 1 ~ 64
●PELCO-D : 1 ~ 80
Certain numbers have special functions other than preset.
33 + PRESET - FLIP COMMAND
97 + PRESET - RANDOM SCAN
98 + PRESET - FRAME SCAN
99 + PRESET - AUTO SCAN
See the camera manual for more information.
●PANASONIC (WV-CS854A) : 1 ~ 64
●Samsung (SCC-641/643) : 1 ~ 127
▤Preset setup is also available in the OSD menu of the connected
camera.
PTZSETUP1
PRESETNO:0
Enter:PresetIDSet
CAMID: 5SPD
PTZSETUP1
Enter:PresetIDSet
CAMID:5SPD
PRESETNO:1
Enter:PTZIDSet
PTZCONTROLSYSTEM
CAMID: 5SPD
MONITOR:1[1]

《17》
PTZ Mode
(3) SWING
■This menu is for setting the camera to alternate between two assigned locations horizontally (pan) or vertically (tilt).
Setting the SWING SETUP menu by controllers is only possible in the SPD series. In case of products by other
manufacturers, the setting has to be done by the OSD menu of the camera. See the camera manual for more
information.
(3-1) SWING Setup
①At the [PTZ SETUP 1 ▶] menu, press the 2 button (see p.15).
②Press the 1 or 2 button to select a horizontal (pan) or vertical (tilt) cycle.
③Set starting point, ending point, movement speed, and stop time.
- I▶/▶▶ button: Moves between items.
- 1ST : Starting point. Can be set for Preset 1 ~ 64.
- 2ND : Ending point. Can be set for Preset 1 ~ 64.
- SPEED : Movement speed. Can be set for 1 ~ 64 (see p.35).
- STOP : Stop time at the starting point and ending point.
Can be set to 1 ~ 99 (seconds).
④Press the ENTER button to finish the setup (takes 2 or 3 seconds to
finish).
▤The Swing function cannot be set if an unassigned number or a
number outside the selectable range is entered.
▤Over 2 PRESET locations have to be set before setting SWING.
(3-2) SWING Operation
①At the initial screen, press the Swing button.
②Press the 1 and 2 buttons to perform the Swing function.
- 1 button: Performs the horizontal cycle (pan).
- 2 button: Performs the vertical cycle (tilt).
▤Move the joystick or press a controller button during the Swing
operation to stop the operation.
▤AUTO-PAN is performed automatically when the SWING button of
PANASONIC(WV-CS854A) and SAMSUNG ELECTRONICS
(SCC-641/643) cameras is pressed.
SWINGSETUP
IST
00 2ND 00 SPEED 00 STOP 00
Enter:SwingSet
PTZCONTROLSYSTEM
CAMID: 5SPD
1:PAN 2:TILT
PressNumericKey
SWINGSETUP
CAMID: 5SPD
1:PANSET 2:TILTSET
PressNumericKey
SWINGSETUP
CAMID: 5SPD
1:PANSET 2:TILTSET
PressNumericKey

《18》
PTZ Mode
(4) GROUP
■This menu is for setting repeated sequential surveillance of assigned locations with assigned speed and intervals.
Setting the GROUP SETUP menu by controllers is only available for an SPD series. In case of products by other
manufacturers, the setting has to be done by the OSD menu of the camera. See the camera manual for more
information.
(4-1) GROUP Setup
①At the [PTZ SETUP 1 ▶] menu, press the 3 button (see p.15).
②Enter a Group number.
▤Any number between 1 and 6 can be selected.
③Set each location’s Preset ID, area movement speed, and stop time.
- I▶/▶▶ button: Moves between items.
- NO : Setup sequence. Up to 64 can be selected.
▤In the case of SPD 2200, setup via the controller is up to 64, but via
the camera OSD menu it can be up to 128.
- PRESET : Camera Preset ID for assigned location.
- SPEED : Area movement speed. Can be set from 1 ~ 64 (see p.35).
- STOP : Stop time at the starting point and ending point.
Can be set to 1 ~ 99 (seconds).
④Press the ENTER button to move to the setup page for the next location.
Press the Group button to finish the Group Setup.
▤The Group function cannot be set if an unassigned number or a
number outside the selectable range is entered.
▤Over 2 PRESET locations have to be set before setting GROUP.
(4-2) GROUP Operation
①At the initial screen, press the Group button.
②Press the Group button to execute the operation.
③The Group function is performed.
▤AUTO-SEQ and SCAN functions are performed when the GROUP
button is pressed (for PANASONIC(WV-CS854A) and SAMSUNG
ELECTRONICS (SCC-641/643 only).
GROUPSETNUM?<1-6>
GROUPSETUP
CAMID: 5SPD
PressNumericKey
GROUPSETUP
NO
01 PRESET 0SPEED 00 STOP 00
Enter:Next Group:Set
GROUPRUNNUM?<1-6>
PTZCONTROLSYSTEM
CAMID: 5SPD
PressNumericKey

《19》
PTZ Mode
(5) TOUR
■This menu is for setting one or more Groups for Tour so that continuous Group operations can be carried out.
The TOUR SETUP menu is only available for an SPD series.
(5-1) TOUR Setup
①At the [PTZ SETUP 1▶] menu, press the 4 button (see p.15).
②Press a Group number to add to the Tour.
▤Up to 6 Groups can be added.
③Press the ENTER button to finish the setup.
(5-2) TOUR Operation
①At the initial screen, press the Tour button.
②The Tour function is performed.
▤The TOUR operation is only available for an SPD series.
TOURSETUP
1GROUPNUM?<1-6>
Enter:TourSet

《20》
PTZ Mode
GROUP 1
TOUR
GROUP 3