Samsung SP-R5200 User manual

Printed in Korea
Code No.: GG68-00059A
U.K. 4/99. Rev.1.0
Your battery is guaranteed for six months. When you purchase the unit, you should
fully charge the battery before initial operation.
DigitalCordlessTelephone
SP-R5200
User’sManual
This equipment is not designed for making emergency
telephony calls when the power fails. Alternative
arrangements should be made for access to
emergencyservices.

2Digital Cordless Telephone 3 Digital Cordless Telephone
When using your telephone, these basic safety precautions
should always be followed to reduce risk of fire, electric
shock, and injury.
1. Never push objects of any kind into your telephone through
case or cabinet openings. They may touch dangerous volt-
age points resulting in risk of fire or shock.
2. To reduce the risk of electric shock, do not disassemble
your telephone. Take it to a qualified service technician
when repair work is required. Opening or removing covers
may expose you to dangerous voltage or other risks.
Incorrect reassembly could cause electric shock when the
unit is subsequently used.
3. Unplug this unit from the telephone jack and wall outlet,
and refer servicing to qualified service personnel under the
following conditions:
•When the power supply cord, plug, or adaptor is dam-
aged or frayed.
•If liquid has been spilled into the product.
•If the product has been exposed to rain or water.
•If the product does not operate properly after instructions
have been followed.
•If the product has been dropped, or the cabinet appears
damaged.
•If the product exhibits a distinct change in performance.
4. Avoid using your telephone during a lightning storm. There
may be a remote risk of electric shock from lightning. If
possible, unplug the AC adaptor and telephone cord for the
duration of the lightning storm.
5. Never dispose of batteries in a fire. There is a serious risk
of explosion and / or the release of highly toxic chemicals.
Dispose of used batteries in accordance with local regula-
tions.
6. When going on holiday or not using the phone for a long
period of time, please disconnect the mains power from the
base and remove the batteries from the handset.
7. If the handset is not used for a long time and the battery
becomes fully discharged, please recharge the handset for
a minimum of 30 hours before using again.
8. If the battery is self-discharged because it has not been
used, the operational life of the battery may be reduced. To
recover the full storage capacity of the battery, recharge the
battery for a minimum of 30 hours and use until it is fully
discharged. This process needs to be repeated several
times.
9. This unit requires rechargeable Ni-MH batteries. Do not use
alkaline batteries.
Safety Precautions and Important Notices

4Digital Cordless Telephone 5 Digital Cordless Telephone
10. Clean the charge points with a dry cloth from time to time.
11. Ringer Equivalence Number (REN)-1.0.
The REN is a customer guide indicating approximately the
maximum number of items of apparatus that should be
connected simultaneously to the line. The sum of REN’s of
the individual items should not exceed a total value of 4.
12. You can use this equipment to make 999, 112 emergency
calls.
13. You can use this equipment on a telecommunication sys-
tem that uses Loop Disconnect or DTMF signalling.
It is strongly recommended that the equipment is config-
ured to use DTMF signalling for access to public or private
emergency services. DTMF signalling also provides faster
call setup.
14. If you are connected to a Private Branch Exchange, you
may have to press a digit, for example “9”, to get an out-
side line. Then you dial as normal. If you need a pause,
you should insert it after the digit and before the number
you require.
15. You may sometimes experience problems in making calls.
These difficulties can include:
• Line connection problems.
•Problems hearing the conversation on both ends of the
line.
16. This equipment will NOT work at all if the mains or bat-
tery supply is removed.
17. You can connect the equipment to the telecommunication
systems specified as long as you follow the instructions in
this manual.
18. This equipment has been approved for use with the fol-
lowing facilities:
• Last Number Redial.
• Call Barring.
• Memory Dial.
Any other use will invalidate the approval of the equip-
ment and it then ceases to comply with the standards
against which approval was granted.
19. SAVE THESE INSTRUCTIONS.

6Digital Cordless Telephone 7 Digital Cordless Telephone
BEFOREUSING
CheckingParts........................................................................................ 8
Control Locations .................................................................................... 9
Handset .............................................................................................. 9
Base ................................................................................................. 10
ConnectingLines................................................................................... 11
Installing Handset Batteries ....................................................................12
Charging the Handset ............................................................................ 14
Using the Handset Carrying Clip .............................................................15
To Attach the Carrying Clip...................................................................15
To Remove the Carrying Clip................................................................15
Turning the Handset On/Off...................................................................16
LCD Window Icon Descriptions................................................................. 17
Choosing Dial Mode................................................................................17
BASICOPERATION
Making a Call ........................................................................................18
Camp on Busy .......................................................................................20
Receiving a Call ..................................................................................... 21
CallerIDDisplay.................................................................................... 22
Out of Range Indication ......................................................................... 23
Battery Level Indicator ..........................................................................23
Adjusting Voice Volume ..........................................................................24
Choosing Ring Type ................................................................................24
Adjusting Ring Volume............................................................................ 25
Key Lock ...............................................................................................26
INTERNALPHONEBOOK
Memory Dialing .....................................................................................27
To Store (or Edit) Numbers In Memory................................................27
Using a Pause ....................................................................................28
ToDialaNumberInMemory .............................................................28
To Search For a Number In Memory....................................................28
ToEraseAllNumbersInMemory ........................................................29
Table of Contents
INTERNALPHONEBOOK (continued)
CallLog..................................................................................................29
To View and Dial the Numbers ............................................................29
To Erase All Numbers Received ...........................................................30
Last Number Redial ...............................................................................30
To View and Dial the Numbers ............................................................30
To Erase All Numbers In Redial Memory..............................................31
USEFULFEATURES
Call Time Display On/Off .......................................................................32
Key Beep On/Off ..................................................................................32
Base Number Display On/Off ................................................................33
Setting Ring Delay Time..........................................................................34
Changing PIN ........................................................................................35
Tone Dial Switchover ..............................................................................36
Registered Recall ...................................................................................37
Barring Calls ..........................................................................................37
To Set Call Barring Numbers ...............................................................38
To Deactivate a Specific Call Barring Number........................................39
Reset .....................................................................................................40
USINGONMULTI SYSTEM
Registering New Handset with Base ........................................................41
To Register a Handset .........................................................................41
To Remove a Handset Registered To the Base Unit ...............................43
Paging...................................................................................................44
Intercom Between Handsets ...................................................................44
Call Transfer ..........................................................................................46
Operating with Additional Base Unit .......................................................47
To Find the Base unit Automatically .....................................................47
To Select the Base Unit Manually ........................................................48
Troubleshooting..................................................................................... 49
Specifications .........................................................................................50

8Digital Cordless Telephone 9 Digital Cordless Telephone
Checking Parts
Once you have unpacked your phone, check to make sure that
you have all the parts shown below. If any piece is missing or
broken, please call your dealer.
Handset
Base
Adaptor
TwoAA Batteries
(Rechargeable Ni-MH batteries)
CarryingClip
User’sManual
LineCord
Control Locations
Antenna
Earpiece
LCDwindow
button
Makes,answers, orends a call.
INT button
Activatesintercom communications.
or button
Scrollsthrough menus.Also adjusts volume.
C/R button
Clearscharacters fromthe display. Also performs
a switch-hook operation such as call waiting.
button
Confirmsthe selection.Also powers on/off.
button
Redials the last number you dialed. Also adds
a pause when storing a number in memory.
Microphone
Rear
Chargingpoints
Batterycover
Carryingclip
Lamp
Handset

10 Digital Cordless Telephone 11 Digital Cordless Telephone
Pagingbutton
Allowsyou topage the handset.
Also used to register a new
handsetwith thebase.
Linelamp
Blinks when a call comes in
and lights steadily when a call
isin progress.
Base
Base Bottom
DC POWER socket
Phone Line socket
Connecting Lines
1. Connect one end of the telephone line cord to the phone line
socket on the bottom of the base unit, and the other end to a
standardphonewall jack.
2. Connect the modular end of the power adapter to the DC power
socket on the bottom of the base unit, and the other end to a
standardACwall outlet.
3. Route the cords through the recessed channel as shown.
To AC wall outlet To phone wall jack

12 Digital Cordless Telephone 13 Digital Cordless Telephone
Installing Handset Batteries
2. Remove old batteries if any, then insert new batteries observing
correct polarity ( + , - ). Reversing the orientation may
damage the handset.
The handset uses the two AA size rechargeable Ni-MH
batteries supplied.
1. Slide the battery cover in the direction of the arrow, then lift it
off.
3. Replace the battery cover. Make sure that the cover is hooked
inplace.
4. Slide the cover up until it snaps shut.
Notes:
•The batteries need to be replaced if they do not recover their
full storage capacity after recharging.
•When replacing batteries, always use good quality Ni-MH
rechargeable AA size batteries. For details, see ‘Specifications’
on page 50. Never use other batteries or conventional alkaline
batteries.

14 Digital Cordless Telephone 15 Digital Cordless Telephone
Charging the Handset
Before initial operation, you should fully charge the handset
for more than 30 hours.
To charge the handset, simply place it on the base unit.
The handset can be charged either face up or face down.
Result: When the handset batteries are charging, the handset
automatically turns on and the battery icon on the left
corner of the display is scrolling.
The lamp
comes on while
charging.
Using the Handset Carrying Clip
To Remove the Carrying Clip
Insert a coin or screw driver into the slot along the edge of one of
its arms, and twist to release. Then lift it off.
The supplied handset carrying clip allows you to conveniently
carry the handset with you. It clips easily to your belt, waist
band, or shirt pocket.
To Attach the Carrying Clip
Attach the carrying clip to the back of the handset. The carrying
clip fits into the grooves on the back of the handset as shown.
Make sure that the carrying clip locks into place.

16 Digital Cordless Telephone 17 Digital Cordless Telephone
Turning the Handset On/Off
When you place the handset in the base unit to charge it, the
handset automatically turns on. To turn the handset on or off
in Standby mode, follow these steps:
1. To turn on the handset when the display is off, press
button.
Result: All segments in the LCD window turn on briefly, then
the phone switches to the Standby mode. The phone is
now ready for use. The display shows the handset
number and the base number as shown below.
2. To turn the handset off, press and hold buttonfor
aboutthreeseconds until appears inthe display.
Result: appears, then the display turns off.
Notes:
•If you purchase an additional handset, you must register the
handset to a base. If not, the display shows
when you turn it on and the handset will not work. Refer to
‘Register New Handset with Base’ on page 41.
•Nothing will appear in the LCD window when battery power is
very low. You should fully charge the handset before operation.
In order to provide compatibility with most telephone systems,
your phone can be set to either pulse-dialling (same as
rotary), or tone dialling (DTMF). Your phone is preset to tone
mode.
1.Press or button repeatedly until appears.
2.Press button to access the menu.
Result: The display shows the current setting.
3.Press or button to choose the desired mode.
4.Press buttonto confirm.
Choosing Dial Mode
LCD Window Icon Descriptions
Battery status icon
In range icon
Memory icon
Handsetkeylockicon
Volume level icon
Line/Intercom/icon
Handset number Base number

18 Digital Cordless Telephone 19
Digital Cordless Telephone
Making a Call
1. Pick up the handset and press button.Youhear a dial
tone.
2. Dial the desired number by using the number keypad.
Note: You can store telephone numbers into one-digit memory
cells (0-9) and dial the numbers using the assigned mem-
ory cell number. Refer to ‘Memory Dialing’ on
page 27.
3. When the other person answers, speak.
4. To end the call, either press buttonorreplace the handset
onthebase unit.
Notes:
•If you turn the ‘Call Time Display’ feature on, the LCD window
displays the call time. For details, see ‘Call Time Display’ on
page 32.
• To make a call to the last number you dialed, use the ‘Redial ‘
feature. For details, refer to ‘Last Number Redial’ on page 30.
You can enter the desired phone number in Standby mode,
and then dial the number. This way of dialing allows you to
make corrections to the number before dialing. Follow these
steps:
1. Enter a telephone number. Check the number in the LCD
window.
Notes:
•If you make a mistake while entering a number, press C/R
button to clear the last digit and correct the number.
•If you press and hold C/R button for more than one second,
all digits you have entered are cleared and the phone
returns to the Standby mode.
2.Whenthe number appearscorrectly, press button.

20 Digital Cordless Telephone 21
Digital Cordless Telephone
(This feature is available only when you have more than
one handset)
This feature allows your handset to wait for connection to the
telephone line currently engaged by another handset. Your
handset rings when the telephone line becomes free.
1. You hear a short busy tone if you press buttonwhile
another handset engages the telephone line.
Result: Your handset is automatically camped on the line.
Note: To cancel this feature, press button any time
before the line is free. The handset returns to Standby
mode.
2.Your handset rings and the window displays whenthe
linebecomesfree.
3.Press button to engage the line while the handset rings.
(Press the button within 10 seconds, or the handset returns to
Standby mode.)
Notes:
•If an incoming call arrives while your handset rings to tell you
the line is free, the ‘Camp On Busy’ feature is automatically
cancelled and an incoming ring sounds.
•Several handsets can be camped on the busy line in chronolog-
ical order. When the line becomes available to you, the LCD
window displays , and other handsets will display your
handset number following the word .
Camp On Busy Receiving a Call
1. When an external call comes in, the phone rings.
Result: The icon on the display blinks, and the green lamp
on the back of the handset flashes.
2.To answer the call, press button.
Or
If the handset is on the base unit, simply lift it up. You do not
needtopress button.
Result: You are connected and the base lamp light is steadily
on.
Note: button and INT button does not work for 3 seconds
to prevent the phone from being disengaged, right after
you lift the phone from the base unit to receive the call.
3. You can speak. To end the call, either press buttonor
replace the handset on the base unit.
Note: If you set the ‘Ring Delay Time’ feature to on, you can turn
the handset ringer off for the specified time when a call
comes in and other handsets are ringing. Refer to ‘Setting
Ring Delay Time’ on page 34.

22 Digital Cordless Telephone 23
Digital Cordless Telephone
Caller ID is a feature available on your phone which helps you
to know who is calling by displaying the caller’s number when
the phone rings. Contact your service provider to activate this
feature.
Notes:
•If there is a missed call (the call not answered), the missing
call number appears in the display.
Your phone keeps track of the last 10 calls received. Refer to
‘Call Log’ on page 29 to check and dial the numbers.
•If a caller has chosen to withhold their number,
is displayed.
• If a caller’s number is not available, you will see
in the display.
• Your Samsung DECT phone has been equipped to receive Caller
Line Identification Presentation or CLIP features that allow you
to see the phone number of the person calling before answer-
ing the call.
The CLIP system used on this product is compatible with the
service currently provided by British Telecom and the majority
of independent Network providers.
In order to use this facility you may have to subscribe to the
service and you should contact your Network provider for infor-
mation on availability and compatibility of this service with
your Network.
Out of Range IndicationCaller ID Display
If the handset is too far from the base unit, the handset can-
not properly engage the telephone line, and the icon
blinks in the LCD window.
If you move out of range during a call, the telephone line
might be disconnected and the handset returns to Standby
mode. Check if the icon blinks in the LCD window. If so, move
the handset closer to the base unit.
This icon blinks when the handset is out
of range in the standby mode.
This icon blinks when the
phone rings.
Aicon is continuously displayed in the upper line of the
LCD window. The icon shows the level of your battery.
The more bars you see, the more power you have left.
When the battery is weak and a few minutes of talk time
remain, you will hear a warning tone and the icon blinks.
When the battery becomes too weak for the phone to operate,
the handset will automatically turn off. Place the handset on
the base unit to charge the handset batteries.
Battery Level Indicator
Full Flat
the caller’s number
There are two missed calls.

24 Digital Cordless Telephone 25
Digital Cordless Telephone
During calls, or button affects the ear piece volume.
You can adjust the volume from level 1 to 5 , and it is pre-
set to level 3. The voice volume is displayed as bars on the
upper right corner of the LCD window. The more bars you
see, the louder the volume is.
Adjusting Ring Volume
1.Press or button repeatedly until appears
inthedisplay.
2.Press button to access the menu.
Result: The current ring level is displayed. You can hear the
volume loudness.
3.Press or button to choose the volume level you want.
Result: You can adjust the volume from level 1 to 3. The higher,
the louder. You can also turn the ringer OFF. Each time
you press. or button, the handset sounds its
selected loudness. The default is ‘Level 2’
4.Press buttonto confirm.
Note: Setting ‘Level Off’ turns the ringer off. When a call comes
in, only the lamp on the back of the handset blinks and the
icon in the window will blink.
Adjusting Voice Volume
Ear piece volume indicator
Choosing Ring Type
You can define your own ringing sound. Six ring types are
available.
1.Press or buttonrepeatedlyuntil
appears.
2.Press button.
3.Press or button to choose the ring type you want.
Result: Each time you press or button, the handset
sounds the ring you have chosen.
4.Press buttonto confirm.

26 Digital Cordless Telephone
Key Lock
If you turn this feature on, all buttons except for but-
ton will be locked and not operate at all.
When a call comes in, you can answer calls by using
button or INT button. But when you finish the call, the phone
returns to the lock mode.
This feature is useful to avoid accidental key pressing.
1. To turn the feature on, press and hold buttonfor
about 1.5 seconds until the iconappearsin the display.
2.To turn the feature off, press and hold button for
about 1.5 seconds until the icon
disappearsinthe display.
Notes:
•If power failure occurs, the ‘Key Lock’ feature is automatically
cancelled.
• Do not hold button for more than three seconds, or the
handset will turn off.
27
Digital Cordless Telephone
Memory Dialing
To Store (or Edit) Numbers In Memory
You can store the most frequently used phone numbers into
one-digit memory cells (0-9).
1.Press or button repeatedly until
appearsinthe display.
2.Press button.
Result: The first memory cell (0) containing a phone number, if
already stored, is displayed.
3. If you want to find another memory cell, press or but-
ton and choose the cell under which you want to save a num-
ber.
4. Enter the desired number (up to 24 digits).
Note: If you make a mistake while entering a number or if you
want to edit a number, press the C/R button. Each time
you press the button, the last digit is cleared. To clear
all digits, press and hold the C/R button. Then enter the
correct number.
5.Press buttonto confirm.

Digital Cordless Telephone
Digital Cordless Telephone 29
4.Press button.
Result: The number is automatically dialed.
To Erase All Numbers In Memory
If you reset the handset, all numbers stored in memory are
erased. Refer to ‘Reset’ on page 40.
Call Log
When you receive a call, the caller’s phone number is shown on
your phone’s display if it is available from the network on which
the call was made. The last 10 numbers received are stored in
your phone and you can view the list and dial the numbers.
To View and Dial the Numbers
1.Press or buttonrepeatedlyuntil appears.
2.Press button.
Result: The LCD window shows the last caller’s number, and
the date and time when the call was received if the
information has been transmitted from the network
with the caller’s number. If there is no number
received, is displayed.
3. Scroll through the memory and choose the desired number by
using or button.
28
Using a Pause
If you want to insert a dialing pause between numbers, press the
button.
Result: appears at the pause entry. A pause is useful when
you access an interactive voice response system, such as
an automated banking system.
To Dial a Number In Memory
Press and hold the cell number for more than one second.
Result: The display shows the phone number stored into the
selected cell and the phone automatically dials the num-
ber.
To Search For a Number In Memory
1.Press or button repeatedly until appearsin
thedisplay.
2.Press button.
3. Scroll through the memory and choose the desired number by
using or button.
Result: The display shows the phone number stored under the
selected cell.

Digital Cordless TelephoneDigital Cordless Telephone 31
2. If you want to scroll through the memory, press or
button until you find the desired number you want to call.
3.Press buttonto dial thenumber.
Notes:
•If there is no number dialed, the message is displayed.
•Each time you dial a new number, the oldest number stored in
the redial memory is automatically erased, and the redial mem-
ory is updated.
• You can modify the number displayed before pressing
button by using C/R button.
• If you press button, followed by button, the phone
dials the last number immediately.
To Erase All Numbers In Redial Memory
1.Press or button until appearsinthe
display.
2.Press button.
Result: All numbers are cleared.
30
4.Press button to dial the selected number.
Notes:
• Your phone stores up to 20 digits for each caller’s number. If
there are hidden digits not displayed, the former part scrolls to
the left and the latter part of the number appears.
•The last number is stored in the memory cell ’0’. When a new
call is received, the previous number is shifted to the next cell
‘1’, allowing the new number to be stored in this position. The
oldest number is automatically erased.
• Depending on the Telephone Networks, some phone numbers
may be truncated.
To Erase All Numbers Received
1.Press or buttonrepeatedlyuntil
appears.
2.Press button.
Result: You hear a beep and the phone returns to the
Standby mode.
Last Number Redial
Your phone allows you to call the most recently dialed num-
bers again. The phone stores the last 10 numbers you called.
To View and Dial the Numbers
1.Press button.
Result: The LCD window displays the last number you dialed.

32 Digital Cordless Telephone 33
Digital Cordless Telephone
Call Time Display On/Off
If you turn the feature on, the handset automatically times the
duration of calls. The handset displays the call duration both
during your call and also for a few seconds after your call is
completed. The feature is preset to ‘OFF’.
1.Press or button repeatedlyuntil appears.
2.Press button.
Result: The display shows the current setting.
3.Press or button to turn the feature On or Off.
4.Press button to save the selected mode.
The feature is preset to ‘ON’ at factory. You can set your
handset not to sound the key beep each time you press a
button.
1.Press or button repeatedly until appears.
Key Beep On/Off
Base Number Display On/Off
This feature allows the phone to display the base number
currently in use while in Standby mode. The feature is preset
to ‘On’ at factory.
1.Press or button until appearsinthe display.
2.Press button.
Result: The display shows the current setting.
3.Press or button to change the current status.
4.Press button to save the selected mode.
2.Press button.
Result: The display shows the current setting.
3.Press or button to turn the feature on or off.
4.Press button to save the selected mode.

34 Digital Cordless Telephone 35
Digital Cordless Telephone
If you activate the ring delay time, your handset will not ring
for the specified delay time while other handsets are ringing.
If you wish, you can answer the call within the delay time on
your handset.
1.Press or button repeatedly until
appears.
2.Press button.
Result: The display shows the current status; for example,
or .
3.Press or button until you choose the desired delay
time.
Result: You can choose from ‘Off’ to 60 seconds using
increments of 5 seconds. Selecting ‘Off’ deactivates
the feature.
4.Press buttonto save thesetting.
Setting Ring Delay Time Changing PIN (Personal Identification Number)
The PIN is required when you bar calls or register handsets to
a base unit. The PIN is preset to ‘0000’ at factory. You can
change the PIN code.
1.Press or button repeatedly until appears
inthedisplay.
2.Press button.
3. Enter the currently used PIN code.
Result: The LCD window dose not display the PIN code you
entered in order to maintain secrecy.
Note: If you enter a wrong PIN code, your phone returns to
Standby mode.
4.Press button.
5. Enter the new PIN code you want.
Note: It must be 4 digits. If you enter a wrong number, you can
correct the number by using the C/R button.

36 Digital Cordless Telephone 37 Digital Cordless Telephone
6.Press button.
7. Enter the new PIN code again to confirm the number.
8.Press button.
Note:If you change the PIN code and then forget it, you will
have to contact service center.
Barring Calls
•It is possible to set the phone to restrict numbers that can
be dialed. The phone cannot dial a phone number beginning
with the specific numbers that you specify.
• You can set up to 4 restricted numbers containing up to 4
digits each.
•If you turn the feature on, the handset requires a PIN code
when the restricted number is dialed. If you enter a wrong
number, your phone returns to the Standby mode. If you
enter a correct PIN, you can make calls.
Note: You can make an emergency call (112, 999) even when
you activate the outgoing call barring option.
The C/R button is used in conjunction with special services
such as ‘Call waiting’ which may be offered by your tele-
phone company. You can place a new call directly after a
call or transfer a call to another extension under PABX,
using this feature.
To send a flash, simply press C/R button while the line is
engaged.
Result: The display shows .
Registered Recall
Tone Dial Switchover
To access certain services such as voice mail or interactive
telephone system features, it is necessary to use tone dialing.
When your phone is set to the pulse mode, DTMF dialing is
available.
1.Pressthe asterisk ( ) while on the phone in the pulse dial
mode.
Result: Your phone is converted to the tone dial mode tem-
porarily.
2. When you finish the call, the phone automatically returns to the
pulsemode.
Note: If you press the C/R button during a call, the phone also
returns to the pulse mode.

38 Digital Cordless Telephone 39
Digital Cordless Telephone
To Set Call Barring Numbers
1.Press or button repeatedly until
appears.
2.Press button.
3.Enterthe PIN code.
Result: If the correct PIN is entered, the first barring cell
containing a restricted number, if already registered,
appears.
4.Press button.
5. If you want to choose another barring cell, press or
button.
6. Enter the number you want to restrict. This can be up to four
digits.
Note:If you make a mistake while entering a number to
restrict, use the C/R button to delete the last digit, then
correct the number.
7.Press button when you finish entering the number.
To Deactivate a Specific Call Barring Number
You can selectively deactivate restricted numbers by
erasing them.
1.Press or buttonrepeatedly until
appears.
2.Press button.
3. Enter the PIN code.
Result: The first barring cell containing a restricted number, if
already registered, appears in the display.
4.Press button.
5. If you want to choose another barring cell, press or
button.
6. When the cell contains the restricted number you want to erase
appearsinthe display, pressand hold C/R button.
7.Press buttonto confirm.