Samsung Ubigate iBG1000 User manual

COPYRIGHT
This manual is proprietary to SAMSUNG Electronics Co., Ltd. and is protected by copyright.
No information contained herein may be copied, translated, transcribed or duplicated for any commercial
purposes or disclosed to the third party in any form without the prior written consent of SAMSUNG
Electronics Co., Ltd.
TRADEMARKS
Ubigate iBG1000 is a registered trademark of SAMSNUG Electronics.
All other company and product names may be trademarks of the respective companies with which they
are associated.
WEEE SYMBOL INFORMATION
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other
household wastes at the end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
This manual should be read before the installation and operation, and the operator should
correctly install and operate the product by using this manual.
This manual may be changed for the system improvement, standardization and other technical
reasons without prior notice.
If you have a question for the content of manual or want to obtain further information on the
updated manual, please contact the homepage below.
Homepage: http://www.samsungdocs.com
©2008 SAMSUNG Electronics Co., Ltd. All rights reserved.

Ubigate iBG1000 Quick Start Guide
© SAMSUNG Electronics Co., Ltd. I
GENERAL USER INFORMATION
RADIO FREQUENCY INTERFERENCE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC REQUIREMENTS
This equipment, the Ubigate iBG1000, complies with Part 68 of the
FCC rules and the requirements adopted by the ATCA. On the bottom of
this equipment is a label that contains, among other information, a
product identifier in the format US: A3LIS00BiBG1000. If requested,
this number must be provided to the telephone company.

GENERAL USER INFORMATION
II © SAMSUNG Electronics Co., Ltd.
UNAUTHORIZED MODIFICATIONS
Any changes or modifications performed on this equipment that are not
expressly approved in writing by SAMSUNG ELECTRONICS, CO.,
LTD. could cause non-compliance with the FCC rules and void the
user’s authority to operate the equipment.
Allowing this equipment to be operated in such a manner as to
not provide for proper answer supervision is a violation of Part 68
of the FCC’s rules.
TELEPHONE CONNECTION REQUIREMENT
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ATCA. A compliant telephone
cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See
installation instructions for details.
FCC Part 68
This equipment complies with Part 68 of the FCC rules. The FCC Part
68 label is located on the bottom chassis panel. This label contains the
FCC Registration Number and Ringer Equivalence Number (REN) for
this equipment. If requested, this information must be provided to your
telephone company.

Ubigate iBG1000 Quick Start Guide
© SAMSUNG Electronics Co., Ltd. III
INCIDENCE OF HARM
If this equipment, the Ubigate iBG1000, causes harm to the telephone
network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice isn’t
practical, the telephone company will notify the customer as soon as
possible. Also, you will be advised of your right to file a complaint with the
FCC if you believe it is necessary.
SERVICE CENTER
If trouble is experienced with the Ubigate iBG1000, please contact your
local office of SAMSUNG ELECTRONICS, CO., LTD. for repair or
warranty information. If the trouble is causing harm to the telephone
network, the telephone company may request that you remove the
equipment from the network until the problem is resolved.
FIELD REPAIRS
Only technicians certified on the Ubigate iBG1000, are authorized by
SAMSUNG ELECTRONICS, CO., LTD. to perform system repairs.
Certified technicians may replace modular parts of a system to repair or
diagnose trouble. Defective modular parts can be returned to
SAMSUNG ELECTRONICS, CO., LTD. for repair.
GENERAL
Connection to party line service is subject to state tariffs. Contact the
state public utility commission, public service commission or
corporation commission for information.

GENERAL USER INFORMATION
IV © SAMSUNG Electronics Co., Ltd.
Electrical Safety Advisory
Parties responsible for equipment requiring AC power should consider
including an advisory notice in their customer information suggesting
the customer use a surge arrestor. Telephone companies report that
electrical surges, typically lightning transients, are very destructive to
customer terminal equipment connected to AC power sources. This has
been identified as a major nationwide problem.
SAFETY WARNING
High touch current earth connection essential before making
telecommunication network connection.
Energy Hazard-careful treatment is needed.
Every wire for communication should be larger than 26 AWG.
Double pole/neutral fusing.

Ubigate iBG1000 Quick Start Guide
© SAMSUNG Electronics Co., Ltd. V
UNDERWRITERS LABORATORIES
The Ubigate iBG1000 system has been tested to comply with safety
standards in the United States and Canada. This system is listed with
Underwriters Laboratories. The cUL Mark is separately shown on the
label.
The following statement from Underwriters Labs applies to the Ubigate
iBG1000 System:
1. Separation of TNV and SELV - Pluggable A:
INSTRUCTION: The separate protective earthing terminal provided
on this product shall be permanently connected to earth.
2. Separation of TNV and SELV - Pluggable B:
INSTRUCTION: Disconnect TNV circuit connector (s) before
disconnecting power.
3. Warning to service personnel:
CAUTION: Double pole/neutral fusing
4. Telephone line cord:
CAUTION: To reduce the risk of fire, use only No. 26 AWG or
larger (e.g., 24 AWG) UL Listed or CSA Certified
Telecommunication Line Cord

GENERAL USER INFORMATION
VI © SAMSUNG Electronics Co., Ltd.
5. Leakage currents due to ringing voltage - Earthing installation
instructions: ‘1. A supplementary equipment earthing conductor is
to be installed between the product or system and earth, that is, in
addition to the equipment earthing conductor in the power supply
cord.
2. The supplementary equipment earthing conductor may not be
smaller in size than the unearthed branch-circuit supply conductors.
The equipment earthing conductor is to be connected to the product
at the terminal provided, and connected to earth in a manner that ill
retain the earth connection when the power supply cord is
unplugged.
The connection to earth of the supplementary earthing conductor
shall be in compliance with the appropriate rules for terminating
bonding jumpers in Part K of Article 250 of the National Electrical
Code, ANSI/ NFPA 70 and Article 10 of Part 1 of the Canadian
Electrical Code, Part 1, C22.1. Termination of the supplementary
earthing conductor is permitted to be made to building steel, to a
metal electrical raceway system, or to any earthed item that is
permanently and reliably connected to the electrical service
equipment earthed.
3. Bare, covered, or insulated earthing conductors are acceptable.
A covered or insulated conductor must have a continuous outer
finish that is either green, or green with one or more yellow stripes.’

Ubigate iBG1000 Quick Start Guide
© SAMSUNG Electronics Co., Ltd. VII
6. Safety Instructions - Rack Mount ‘Rack Mount Instructions -
The following or similar rack-mount instructions are included with
the installation instructions:
A) Elevated Operating Ambient - If installed in a closed or multi-
unitrack assembly, the operating ambient temperature of the
rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the
equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack
should be such that the amount of air flow required for safe
operation of the equipment is not compromised.
C) Mechanical Loading - Mounting of the equipment in a rack
should be such that a hazardous condition is not achieved due
to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the
connection of the equipment to the supply circuit and the
effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used
when addressing this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted
equipment should be maintained. Particular attention should be
given to supply connections other than direct connections to the
branch circuit (e.g., use of power strips).’

GENERAL USER INFORMATION
VIII © SAMSUNG Electronics Co., Ltd.
This page is intentionally left blank.

Ubigate iBG1000 Quick Start Guide
© SAMSUNG Electronics Co., Ltd. IX
TABLE OF CONTENTS
GENERAL USER INFORMATION.........................................................I
RADIO FREQUENCY INTERFERENCE............................................... I
FCC REQUIREMENTS......................................................................... I
SAFETY WARNING ............................................................................ IV
UNDERWRITERS LABORATORIES ................................................... V
Ubigate iBG1000 Quick Start Guide ..................................................1
Inspecting the Ubigate iBG1000............................................................... 1
Ubigate iBG1000 Status LED ............................................................... 2
Ubigate iBG1000 Rear Side ................................................................. 4
Safety Recommendations .................................................................... 5
Installing the Ubigate iBG1000 ................................................................. 6
Installing on a tabletop ......................................................................... 6
Installing on a wall................................................................................ 7
Connecting the Ubigate iBG1000 ........................................................... 10
Connecting to the Network................................................................. 10
Powering Up the Ubigate iBG1000 .................................................... 15
Initial Configuration................................................................................. 17
Changing Login Parameters............................................................... 17
Verifying the Hardware Configuration................................................. 23
Default Configuration ......................................................................... 23

TABLE OF CONTENTS
X© SAMSUNG Electronics Co., Ltd.
This page is intentionally left blank.

Ubigate iBG1000 Quick Start Guide
© SAMSUNG Electronics Co., Ltd. 1
Ubigate iBG1000 Quick Start Guide
Inspecting the Ubigate iBG1000
After opening the shipping carton, remove and save all packing materials
and boxes.
Save the packing materials. If you need to return the product,
you will need to repack the unit.
Check the packing slip and contents of the shipping carton to ensure that
you have received the following:
Ubigate iBG1000 body
Console cable DB-9 to RJ-45 cable adapter
AC/DC Power adapter
Plastic anchor and screw 2 sets
Quick Start Guide
Manual CD

Ubigate iBG1000 Quick Start Guide
2© SAMSUNG Electronics Co., Ltd.
Inspect the Ubigate iBG1000 for damage that may have occurred during
shipping. If you discover damage or missing items, contact Technical
Support:
http://www.samsungnetwork.com
Ubigate iBG1000 Status LED
LED in the top of the Ubigate iBG1000 indicates the status of the
Ubigate iBG1000’s performance and operation. Each LED’s description
is shown as follows.
T1/E
P0 P1 P2 P3
P0
P1
SYS
Ethernet

Ubigate iBG1000 Quick Start Guide
© SAMSUNG Electronics Co., Ltd. 3
Status LED Description
LED Indication &
Color Description
Solid green System is operating normally.
Solid red System is not operating normally.
Amber System diagnostic mode.
SYS
Off Router is not receiving power.
Solid green T1/E1 port is operating normally.
Solid red T1/E1 port cable is not connected properly or
critical alarm detected.
Amber User alarm detected.
P0 ~ P3
(T1/E1)
Off Router is not operating normally.
Solid green Ethernet port link is detected.
Blinking green Ethernet port activity is detected.
P0 ~ P1
(Ethernet)
Off Ethernet port link is not detected.
Solid blue Power supply installed and operating normally.
Amber Power supply installed but power fault condition
detected.
(Power)
Off Power supply not present or power supply failure.

Ubigate iBG1000 Quick Start Guide
4© SAMSUNG Electronics Co., Ltd.
Ubigate iBG1000 Rear Side
The Ubigate iBG1000 rear panel provides connections for networking.
The Ubigate iBG1000 rear panel provides connections for two Fast
Ethernet ports and four T1/E1 ports.
Rear Connector Description
Connector Description
T1/E1 Port T1/E1 WAN connection
Fast Ethernet UTP Port Fast Ethernet LAN connection
Console Port Serial port for local monitoring and configuring
Auxiliary Port Serial port for remote monitoring
Power Connector DC power connector
T1/E1 Ports Fast Ethernet
UTP Ports
Console Port Auxiliary Port
Power Connecto
r

Ubigate iBG1000 Quick Start Guide
© SAMSUNG Electronics Co., Ltd. 5
Safety Recommendations
The safety warnings that appear in this document (such as the one
below) indicate a procedure that can harm you if not done correctly.
Electric hazard exists. Verify the power is turned off. Do not work
on energized equipment. Working on energized equipment can
result in serious electrical shock.
To avoid electric shock, do not connect safety extra-low voltage
(SELV) circuits (as found in LAN ports) to telephone-network
voltage (TNV) circuits (as found in WAN ports). Be sure to follow
connection instructions carefully.
This equipment must be installed and maintained by properly
trained service personnel. Make sure the proper electrical
service is available before plugging this unit in and turning it on.
Disconnect the telecommunications lines before unplugging the
main power connector.
Cover Panels
Do not operate the Ubigate iBG1000 with missing cover panel.
The cover prevents exposure to hazardous voltages and currents inside
the chassis. It is important to maintaining proper air flow through the
chassis. It also prevents electromagnetic interference (EMI) that might
disrupt other equipment.

Ubigate iBG1000 Quick Start Guide
6© SAMSUNG Electronics Co., Ltd.
Installing the Ubigate iBG1000
This section describes how to prepare the Ubigate iBG1000 for
operation either as a tabletop or a wall-mounted unit.
Installing on a tabletop
Allow sufficient room at the front, rear, and side of the unit for interface
cabling, power cord clearance, and adequate ventilation.
Set the device on a flat surface, making sure there are sufficient spaces
on all sides for proper air flow.
Do not place any items that weigh more than 10 pounds (4.5
kilograms) on top of the chassis, and do not stack routers on a
tabletop.

Ubigate iBG1000 Quick Start Guide
© SAMSUNG Electronics Co., Ltd. 7
Installing on a wall
This section describes how to install Ubigate iBG1000 on a wall.
1. Mark two holes, horizontally or vertically, on a desired wall.
The hole distance is about 130 mm.
2. Make holes on the marked position with an electric drill. Make the
depths and the diameters of the holes more than 33 mm and around
5.5 mm to insert the plastic anchors easily, respectively.

Ubigate iBG1000 Quick Start Guide
8© SAMSUNG Electronics Co., Ltd.
3. With a hammer, insert plastic anchors into the holes.
4. Insert screws to each hole and tighten the screws with a Phillips
screwdriver. Be sure to remain screws untightened about 2 mm.