Samsung Ubigate iBG1003 User manual

COPYRIGHT
This manual is proprietary to SAMSUNG Electronics Co., Ltd. and is protected by copyright.
No information contained herein may be copied, translated, transcribed or duplicated for any
commercial purposes or disclosed to third parties in any form without the prior written consent of
SAMSUNG Electronics Co., Ltd.
TRADEMARKS
Ubigate iBG1003 is a registered trademark of SAMSNUG Electronics.
All other company and product names may be trademarks of the respective companies with which
they are associated.
This manual should be read before the installation and operation, and the operator should
correctly install and operate the product by using this manual.
This manual may be changed for the system improvement, standardization and other technical reasons
without prior notice.
If you have a question for the content of manual or want to obtain further information on the updated
manual, please contact the homepage below.
Homepage: http://www.samsungdocs.com
©2009~2010 SAMSUNG Electronics Co., Ltd. All rights reserved.

Ubigate iBG1003 Installation Manual
© SAMSUNG Electronics Co., Ltd. I
GENERAL USER INFORMATION
Radio Frequency Interference
The Ubigate iBG1003 equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to FCC Part 15 Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his/her own risk.

GENERAL USER INFORMATION
II © SAMSUNG Electronics Co., Ltd.
FCC Requirements
The Ubigate iBG1003 equipment complies with FCC Part 68 Rules and
requirements adopted by Administrative Council for Terminal Attachment
(ATCA).
FCC Part 68
The FCC Part 68 label is located on the bottom of the chassis.
The label contains:
Product Identifier Number
FCC Registration Number
Ringer Equivalence Number (REN)
NOTE
If requested, this information must be provided to your telephone
company.
Unauthorized Modifications
Any change or modifications performed on this equipment that are not
expressly approved in writing by SAMSUNG ELECTRONICS, CO., LTD.
could cause non-compliance with the FCC rules and void the user’s authority
to operate the equipment.

Ubigate iBG1003 Installation Manual/Ed.04
© SAMSUNG Electronics Co., Ltd. III
Telephone Connection Requirement
A plug and jack is used to connect this equipment to the premises wiring and
telephone network must comply with the FCC Part 68 rules and requirements
adopted by the ACTA.
A compliant telephone cord and modular plug is provided with this product
which is designed to connect to a compatible Standard Modular jack.
Connection to the telephone network should be made by using standard
modular telephone jacks, type RJ-11C. The RJ-11C plug and/or jacks used
must comply with the FCC Part 68 rules.
CIRCUIT TYPE MODULE TYPE FACILITY INTERFACE
CODE
NETWORK
JACK
LOOP START
LINE FXO T1E1 02LS2 04DU9.DN
04DU9.1KN
04DU9.1SN
04DU9.1SN (PRI)
RJ11C
RJ48C
DID LINE FXS
T1E1 02RV2.T 04DU9.BN RJ11C RJ48C
E & M TIE LINE T1E1 04DU9.BN RJ48C
Ringer Equivalence Number
The REN is used to determine the number of devices to be connected to a
telephone line. If the total allowable REN load is exceeded, the phone circuit
may fail to ring. In most cases, the total REN for a telephone line should not
exceed Five (5).
Contact Local Telephone Company, to be certain about the number of devices
connected to a line, which is determined by the total REN.
For earlier products, the REN is separately shown on the label.

GENERAL USER INFORMATION
IV © SAMSUNG Electronics Co., Ltd.
Incidence of Harm
The telephone company will notify you in advance about the temporary
discontinuation of service, if the Ubigate iBG1003 equipment is causing harm
to the telephone network.
In case advance notification is not feasible, the telephone company will notify
the customer as soon as possible and you will also be advised about your right
to file a complaint with the FCC, if it is necessary.
Changes to Telephone Company Equipment or
Facilities
The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment.
If this happens, the telephone company will provide advance notice in order
for you to make necessary modifications to maintain uninterrupted service.
Service Center
If you need assistance during troubleshooting, please contact out local office
SAMSUNG ELECTRONICS, CO., LTD. for repair or warranty information.
If the trouble is causing harm to the telephone network, the telephone
company may request you to remove the equipment from the network until the
problem is resolved.
Field Repairs
Only technicians certified on the Ubigate iBG1003 are authorized by
SAMSUNG ELECTRONICS, CO., LTD. to perform system repairs.
Certified technicians may replace modular parts of a system to repair or
diagnose trouble. Defective modular parts can be returned to SAMSUNG
ELECTRONICS, CO., LTD. for repair.

Ubigate iBG1003 Installation Manual/Ed.04
© SAMSUNG Electronics Co., Ltd. V
General
Connection to party line service is subject to state tariffs. Contact the State
Public Utility Commission, Public Service Commission or Corporation
Commission for information.
Direct Inward Dialing (‘DID’)
If the equipment is not operating as per the ProperAnswer Supervision
mentioned in FCC Part 68 rules, then it is a violation.
Rules of PROPER ANSWER SUPERVISION:
1. Always On the following DID calls, the Equipment returns Answer
Supervision to the Public Switched Telephone Network (PSTN)
Answered by the called station.
Answered by the attendant.
Routed to a recorded announcement that can be administered by the
Customer Premises Equipment (CPE) user.
Routed to a dial prompt.
2. Always this equipment returns answer supervision on all DID calls
forwarded to the PSTN.
Permissible exceptions are:
A call is unanswered.
A busy tone is received.
A reorder tone is received.
Equal Access Requirements
Through the use of access codes, this equipment is capable of providing user’s
access to interstate providers of operator services. Modification of this
equipment by call aggregators to block access dialing codes is a violation of
the Telephone Operator Consumers Act of 1990.

GENERAL USER INFORMATION
VI © SAMSUNG Electronics Co., Ltd.
Electrical Safety Advisory
Parties responsible for equipment requiringAC power should consider
including an advisory notice in their customer information suggesting them to
use a surge arrestor. Telephone companies report that electrical surges,
typically lightning transients, are very destructive to customer terminal
equipment connected to AC power sources. This has been identified as a major
nationwide problem.
Music on Hold Warning
In accordance with US copyright laws, a license may be required from
the American Society of Composers,Authors and Publishers
(ASCAP) or other similar organizations if copyright music is
transmitted through the Music on Hold feature.
SAMSUNG ELECTRONICS, CO., LTD. hereby disclaims any liability
arising out of failure to obtain such a license.
Direct Inward System Access (DISA) Warning
The lines used for the DISA feature must have the disconnected Supervision
option provided by the telephone company.
As it is impossible to control who may access your DISAline it is
suggested that you do not turn this feature on unless you intend to
use it. If you do use this feature, it is good practice to frequently
change pass codes and periodically review your telephone records for
unauthorized use.

Ubigate iBG1003 Installation Manual/Ed.04
© SAMSUNG Electronics Co., Ltd. VII
Safety Warnings
High touch current earth connection is essential before making
telecommunication network connection.
Energy Hazard-careful treatment is needed.
Every wire for communication should be larger than 26 AWG.
Double pole/neutral fusing.
Underwriters Laboratories
The Ubigate iBG1003 system has been tested to comply with Safety Standards
in the United States and Canada. This system is listed with Underwriters
Laboratories. The cUL Mark is separately shown on the label.

GENERAL USER INFORMATION
VIII © SAMSUNG Electronics Co., Ltd.
Installation Safety Guidelines and Warnings
Safety Recommendations
The Safety Warnings that appear in this document (such as the one below)
indicate a procedure that can harm you if not done correctly.
Electric hazard exists. Verify the power is turned off. Do not work on
energized equipment. Working on energized equipment can result in
serious electrical shock.
To avoid electric shock, do not connect Safety Extra-Low Voltage
(SELV) circuits (found in LAN ports) to Telephone-Network Voltage
(TNV) circuits (found in WAN ports).
This equipment must be installed and maintained by properly trained
service personnel. Make sure the proper electrical service is available
before plugging the unit and turning it on. Disconnect the
telecommunication lines before unplugging the main power connector.
Cover Panels
Do not operate the Ubigate iBG1003 with missing blank faceplates and cover
panels. These covers prevent exposure to hazardous voltages and currents
inside the chassis. They are important to maintaining proper air flow through
the chassis. They also prevent electromagnetic interference (EMI) that might
disrupt other equipment.
Laser radiation and EMI are present when the router cover panel is
open.

Ubigate iBG1003 Installation Manual/Ed.04
© SAMSUNG Electronics Co., Ltd. IX
Electrostatic Discharge (ESD) Warning
Observe the following guidelines to minimize the potential for Electrostatic
Discharge (ESD) damage, which can cause intermittent or complete
component failures.
When handling Ubigate iBG1003 or its components, wear grounding
wrist straps to avoid ESD damage to the equipment. Do not directly
touch the backplane with your hand or any metal tool, or you could
shock yourself.
1. Always use an ESD wrist strap or ankle strap, and verify that it is in
direct contact with your skin. Avoid contact between the component and
your clothing as it causes ESD damage.
2. When handling any component that is removed from the chassis, verify
that the equipment end of your ESD strap is attached to one of the ESD
points on the chassis.
3. Use care when installing or uninstalling modules or interface cards.
Tighten the captive installation screws to ensure a proper connection
when inserting modules or interface cards.
4. When removing or installing a component, always place it component-
side up on an antistatic surface, in an antistatic card rack. If you are
returning a component, place it in an electrostatic bag before packing it.

GENERAL USER INFORMATION
X© SAMSUNG Electronics Co., Ltd.
This page is intentionally left blank.

Ubigate iBG1003 Installation Manual
© SAMSUNG Electronics Co., Ltd. XI
INTRODUCTION
Purpose
This document provides instructions on installing the Ubigate iBG1003™,
along with hardware descriptions, safety information, and pre-installation
requirements.
Document Content and Organization
This manual is composed of five Chapters and two Annexes.
CHAPTER 1. Ubigate iBG1003 Overview
Describes Ubigate iBG1003 characteristics.
CHAPTER 2. Pre-Installation Requirements
Describes the safety regulation and how to prepare for installation.
CHAPTER 3. Ubigate iBG1003 Installation
Describes how to install Ubigate iBG1003.
CHAPTER 4. Connecting the Ubigate iBG1003
Describes how to connect various interfaces of Ubigate iBG1003.
CHAPTER 5. Option Module Installation
Describes how to install option modules.

INTRODUCTION
XII © SAMSUNG Electronics Co., Ltd.
ANNEX A. System Specifications
Describes system specifications.
ANNEX B. Cable Specifications
Describes cable specifications.
Conventions
The following types of paragraphs contain special information that must be
carefully read and thoroughly understood. Such information may or may not
be enclosed in a rectangular box, separating it from the main text, but is
always preceded by an icon and/or a bold title.
WARNING
Provides information or instructions that the reader should follow in
order to avoid personal injury or fatality.
CAUTION
Provides information or instructions that the reader should follow in
order to avoid a service failure or damage to the system.
NOTE
Indicates additional information as a reference.

Ubigate iBG1003 Installation Manual/Ed.04
© SAMSUNG Electronics Co., Ltd. XIII
Information for Product and Technical Support
For questions regarding the product and technical supports:
http://www.samsungnetwork.com
Revision History
EDITION DATE OF ISSUE REMARKS
00 04. 2009. First Edition
01 06. 2009. Modified voice connector description
02 09. 2009. Added VOM-4P
03 12. 2009. Added VOM-2T4
04 07. 2010. Added LMF-4M

INTRODUCTION
XIV © SAMSUNG Electronics Co., Ltd.
This page is intentionally left blank.

Ubigate iBG1003 Installation Manual
© SAMSUNG Electronics Co., Ltd. XV
SAFETY CONCERNS
The purpose of the Safety Concerns section is to ensure the safety of users and prevent property
damage. Please read this document carefully for proper use.
Symbols
Caution
Indication of a general caution.
Restriction
Indication for prohibiting an action for a product.
Instruction
Indication for commanding a specifically required action.

SAFETY CONCERNS
XVI © SAMSUNG Electronics Co., Ltd.
Warning
Electric hazard exists. Verify the power is turned off. Do not work on
energized equipment. Working on energized equipment can result in
serious electrical shock.
Laser radiation and EMI are present when the router cover panel is
open.
- External grounding is required to prevent human injuries or system
damages caused by lightning, static electricity, or voltage surge.
- The power plug of iBG1004 system should be connected to an
outlet with a protective ground.
When handling Ubigate iBG1003 components, wear grounding wrist
straps to avoid ESD damage to the card.
To avoid electric shock, do not connect Safety Extra-Low Voltage
(SELV) circuits (as found in LAN ports) to Telephone-Network Voltage
(TNV) circuits (as found in WAN ports).
AC power to the Ubigate iBG1003 is double fused. Fuses are
installed on both line and neutral conductors.
A neutral fuse failure may present a hazard to service personnel.
Disconnect the AC Line Cord or remove both AC fuses before
servicing the unit.
WARNING

Ubigate iBG1003 Installation Manual/Ed.04
© SAMSUNG Electronics Co., Ltd. XVII
Caution
Do not place any items that weigh more than 4.5 kg on top of the
chassis, and do not stack routers on a desktop.
Practice good safety habits. Use two people to mount the Ubigate
iBG1003 into a rack.
This equipment must be installed and maintained by properly trained
service personnel. Make sure the proper electrical service is available
before plugging this unit in and turning it on.
Disconnect the telecommunications lines before unplugging the main
power connector.
CAUTION

SAFETY CONCERNS
XVIII © SAMSUNG Electronics Co., Ltd.
This page is intentionally left blank.