Samsung iPolis SNV-1080R User manual

NETWORK CAMERA
User Manual SNV-1080R

Copyright
©2012 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall
be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own
responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.
The default password can be exposed to a hacking thread so it is recommended to change the password
after installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible
for the user.
Network Camera
User Manual

English _3
●OVERVIEW
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
overview

overview
4_ overview
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
To prevent injury, this apparatus must be securely attached to the Wall/ceiling
in accordance with the installation instructions.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.

English _5
●OVERVIEW
Class construction
An apparatus with CLASS construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
Battery
Batteries(battery pack or batteries installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call
a repair man in your location.
When used outside of the U.S., it may be used HAR code with fittings of
an approved agency is employed.
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
The BNC Out terminal of the product is provided for easier installation, and is
not recommended for monitoring purposes.
If you keep the BNC cable connected, a risk of lightening may cause damage
or malfunction to the product.
Please use the input power with just one camera and other devices must not
be connected.

overview
6_ overview
Please read the following recommend safety precautions carefully.
Do not place this apparatus on an uneven surface.
Do not install on a surface where it is exposed to direct sunlight, near
heating equipment or heavy cold area.
Do not place this apparatus near conductive material.
Do not attempt to service this apparatus yourself.
Do not place a glass of water on the product.
Do not install near any magnetic sources.
Do not block any ventilation openings.
Do not place heavy items on the product.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
Reference : In case of providing information for helping of product’s usages
Notice : If there’s any possibility to occur any damages for the goods and
human caused by not following the instruction
Please read this manual for the safety before using of goods and keep it in
the safe place.

English _7
●OVERVIEW
CONTENTS
OVERVIEW
3
3Important Safety Instructions
9Product Features
9Recomended PC Specifications
10 Recomended Micro SD/SDHC
Memory Card Specifications
10 What’s Included
11 At a Glance
INSTALLATION &
CONNECTION
13
13 Installation
15 Inserting/Removing an SD
Memory Card
16 Memory Card Information
(Not Included)
17 Connecting with other Device
NETWORK CONNECTION
AND SETUP
20
20 Connecting the Camera Directly
to Local Area Networking
21 Connecting the Camera Directly
to a DHCP Based DSL/Cable
Modem
22 Connecting the Camera Directly
to a PPPoE Modem
23 Connecting the Camera to a
Broadband Router with the
PPPoE/Cable Modem
24 Buttons used in IP Installer
25 Static IP Setup
29 Dynamic IP Setup
30 Port Range Forward (Port Mapping)
Setup
32 Connecting to the Camera from a
Shared Local PC
32 Connecting to the Camera from a
Remote PC via the Internet

overview
8_ overview
SETUP SCREEN
44
44 Setup
44 Audio & Video Setup
52 Network Setup
59 Event Setup
66 System Setup
APPENDIX
71
71 Specification
76 Product Overview
77 Troubleshooting
79 Open Source Announcement
80 License
83 GPL/LGPL Software License
WEB VIEWER
33
33 Connecting to the Camera
34 Login
35 Installing ActiveX
36 Installing Silverlight Runtime
38 Using the Live Screen
41 Search and play by event
42 Search and play by time

English _9
●OVERVIEW
PRODUCT FEATURES
• Multi-Streaming
This network camera can display videos in different resolutions and qualities
simultaneously using different CODECs.
• Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
• Alarm
If an event occurs, the event-related video will be transferred to the email specified by the
user, or saved to the SD memory.
• Video Motion Detection
Detects a motion from the video before triggering an event.
• Face Detection
Recognizes a face from the camera input video, or transfers a clearer image of your specified
area.
• Auto Detection of Disconnected Network
Detects network disconnection before triggering an event.
• ONVIF Compliance
This product supports ONVIF.
For more information, refer to www.onvif.org.
RECOMENDED PC SPECIFICATIONS
•CPU : Intel(R) Core(TM)2 2.4 GHz or higher
•Operating System : Windows XP, VISTA, 7
Mac OS
•Resolution : 1280X1024 pixels or higher
•RAM : 2GB or higher
•Web Browser : Internet Explorer 7.0 or later, Firefox 3.0 or later, Chrome 8.0 or later,
Safari 4.0 or later
Neither a beta test version unlike the version released in the company website nor the developer version will
be supported.
It is recommended to connect to IPv6 in Windows 7.
•Video Memory : 256MB or higher
J
If the driver of the video graphic adapter is not installed properly or is not the latest version, the
video may not be played properly.
For a multi-monitoring system involving at least 2 monitors, the playback performance can be
deteriorated depending on the system.

overview
10_ overview
RECOMENDED MICRO SD/SDHC MEMORY CARD
SPECIFICATIONS
•2GB ~ 32GB
•To ensure proper recording of video data, it is recommended you use a memory card that
supports at least read/write speed 10Mbps and Class 6.
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Appearance Item Name Quantity Description
Camera 1
User Manual,
Installer S/W CD,
CMS S/W DVD
2
Quick Guide 1
Cable for the testing monitor 1 Used to test the camera connection to a
portable display device
Iron Screw 3 Used for fixing to an iron plate
L Wrench 1 Used to remove/fix the dome cover
Template 1 Product installation guide

English _11
●OVERVIEW
AT A GLANCE
Appearance
Item Description

Dome Cover Dome cover for the lens and unit protection.
b
Main unit Main unit includes the lens, switch board, PCB boards and screws.
c
Power Port Used to plug the power cable.

Alarm Input Port
BROWN = Alarm IN Used to connect the alarm input sensor.
BLACK = GND Used for earth-grounding.

Network Port Used to connect a PoE or Ethernet cable.

Audio In Jack Used to connect to a microphone.

Audio Out Jack Used to connect to speakers.

overview
12_ overview
Components
Item Description

Reset Button
Resets the camera settings to the default.
Press and hold for about 5 seconds to reboot the system.
JIf you reset the camera, the network settings will be adjusted so that
DHCP can be enabled. If there is no DHCP server in the network, you
must run the IP Installer program to change the basic network settings
such as IP address, Subnet mask, Gateway, etc., before you can
connect to the network.
b
Micro SD Memory
Card Compartment Compartment for the Micro SD memory card.
c
Illumination Sensor Detects incoming light to control the IR LED.

Monitor Out Using the test monitor cable, you can connect to a mobile display for camera
test. (for installation)

Focus lever Turn the barrel left or right to adjust the focus, and turn the knob clockwise
to lock the focus.

ZOOM lever Turn the barrel left or right to adjust the zoom, and turn the knob clockwise
to lock the zoom.

IR LED These infrared LED’s are controlled by the illumination sensor.
RESETRESET
VIDEO
OUT
5
6
7
43

English _13
●INSTALLATION & CONNECTION
INSTALLATION
Precautions before installation
Ensure you read out the following instructions before installing the camera:
•Select an installation site (ceiling or wall) that can endure at least 5 times of the camera
weight.
•Stuck-in or peeled-off cables can cause damage to the product or a fire.
•For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.
Installing on the ceiling directly
1. Using the L-wrench provided, loosen 3 screws
by turning them counterclockwise and separate
the dome cover.
2. Drill a hole (5 mm in diameter, at least 35 mm in
depth) in a desired position of the case bottom
and insert the provided plastic anchor (HUD 5) to
the end. Fit the bottom hole to the anchor hole
and insert and tighten the ASS’Y tapping screw
(TH M4×L30).
3. Connect power and video cables and arrange
cable running not to damage or squeeze them,
and assemble the camera unit in the reverse way.
4. Adjust the lens aiming to your desired direction.
5. Assemble the Dome Cover.
For waterproof purpose, fix and secure the bolt using L-wrench provided.
installation & connection

installation & connection
14_ installation & connection
Adjusting the monitoring direction for the camera
❖Adjusting the monitoring direction
You can adjust the camera direction only when the camera is fixed on the ceiling.
Then, turning the camera to the left or right is referred to as “Panning”, while tilting the angle
is “Tilting”. For panning, the panning limit is 177.5° for the clockwise, and 177.5° for the
counterclockwise, a total of 352° enabled; further rotation is stopped by the stopper.
- Adjust the panning angle so that the camera settles in the right horizontal position.
You can adjust the panning up to 177.5° in each one direction, and 177.5° in the
other direction, a total of 352°.
- Adjust the tilting angle so that the camera settles in the right vertical position. You can
adjust the tilting between 17° and 90°.
- The total rotation range is 351°. You can make adjustment in one direction up to
124°, and 227° in the other direction.
❖Methods of adjustment
•The case of wall installation
①After mounting the camera on the wall, adjust the panning angle so that the camera
faces a desired direction when tilting.
②Adjust the Rotate position to fit the video to the screen borders.
③Then, adjust the tilting angle so that the camera faces the monitoring direction.
•The case of ceiling installation
①After mounting the camera on the ceiling, adjust the panning angle according to
the monitoring direction. You should adjust the panning angle lest that the video be
displayed upside down on the monitor.
②Adjust the Rotate position to fit the video to the screen borders.
③Then, adjust the tilting angle so that the camera faces the monitoring direction.
J
For smoother Rotate adjustment, set the Tilt position between 60° ~ 80°.
Panning
Tilting
Lens rotation
0˚
17˚ ~ 90˚

English _15
●INSTALLATION & CONNECTION
INSERTING/REMOVING AN SD MEMORY CARD
J
Disconnect the power cable from the camera before inserting the SD memory card.
Inserting an SD Memory Card
Push the SD memory card in the direction of the arrow shown in the diagram.
J
Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the
SD memory card.
Removing an SD Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to
eject the memory card from the slot.

installation & connection
16_ installation & connection
J
Pressing too hard on the SD memory card can cause the card to shoot out uncontrollably from the
slot when released.
To remove the SD memory card, set <Record> to <Off> from <SD record> and press
[Apply ()]. (page 60)
If you have saved data in the SD memory card, removing the SD memory card prior to setting
record to OFF will cause damage to the data stored in the card.
MEMORY CARD INFORMATION (NOT INCLUDED)
What is a memory card?
The memory card is an external data storage device that has been developed to offer an
entirely new way to record and share video, audio, and text data using digital devices.
Selecting a memory card that’s suitable for you
Your camera supports Micro SD/SDHC memory cards.
You may, however, experience compatibility issues depending on the model and make of
the memory card.
For your camera, we recommend you use a memory card from the following
manufacturers:
Micro SD/SDHC Memory Card : Sandisk, Transcend
Playback performance can be affected depending on the speed of memory card, so use
the high-speed memory card.

English _17
●INSTALLATION & CONNECTION
CONNECTING WITH OTHER DEVICE
Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.
Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the camera.
J
Be careful not to reverse the polarity when you connect the power cable.
You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.
If both PoE and DC 12V are supplied, the product will operate with the first-applied power source.
Please make sure the monitor and camera are turned off when connecting them.
Monitor
(for installation)
Power
Ethernet

installation & connection
18_ installation & connection
Connecting to Audio Input/Output
1. Connect the MIC port of the camera with the microphone directly or LINE OUT port
of the amplifier that the microphone is connected to.
2. Connect the SPEAKER port of the camera with the LINE IN port of the speaker.
3. Check the specifications for audio input.
• Audio Codec
G.711 PCM. μ-law 64kbps 8kHz sampling
• Full duplex Audio
• Audio in
Used for mono signal line input (Max.2.4 Vpp)
• Audio out
Used for mono signal line output (Max.2.4 Vpp)
• Line out impedance
600
PC
Network
Speaker
Microphone
Amp
Amp
Microphone
Microphone
Speaker

English _19
●INSTALLATION & CONNECTION
Alarm input Wiring Diagram
To connect to the alarm input port
Connect the alarm input signal to the cable input port.
Port Description Port Description
ALARM IN Alarm Input Sensor Port GND Earth-grounding Port
To connect the alarm input signal
Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port,
and connect the other strand to the [GND] port.
ALARM IN
GND
1
2
(5mA sink)
B
R
O
W
N
=
A
l
a
r
m
I
N
B
L
A
C
K
=
G
N
D
SENSOR

20_ network connection and setup
You can set up the network settings according to your network configurations.
CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA
NETWORKING
Connecting to the camera from a local PC in the LAN
1. Launch an Internet browser on the local PC.
2. Enter the IP address of the camera in the address bar of the browser.
M
A remote PC in an external Internet out of the LAN network may not be able to connect to the
camera installed in the intranet if the port-forwarding is not properly set or a firewall is set.
In this case, to resolve the problem, contact your network administrator.
By factory default, the IP address will be assigned from the DHCP server automatically. If there is
no DHCP server available, the IP address will be set to 192.168.1.100.
To change the IP address, use the IP Installer.
For further details on IP Installer use, refer to “Static IP Setup”. (Page 25)
network connection and setup
Switch
Camera
Camera
Local PC
Firewall External Remote PC
DDNS Server
(Data Center, KOREA)
INTERNET
<Local Network>