Samsung MIM-D00 User manual

INSTALLATION
MANUAL
MIM-D00
DMS
(Data Management Server)
DB98-29919A(1)EK C
CHINESE ENGLISH
MIM-D00_IM_E_29919-1.indd 29 2008-09-10 ｿﾀﾈﾄ 1:27:35

E-2
Safety Precautions
Read carefully this installation manual before
installation and check if the DMS is installed correctly
after installation.
 Do not attempt to install or repair this DMS by yourself.
This DMS contains no user-serviceable parts.
Always consult authorized service personnel for repairs.
When moving, consult authorized service personnel for
disconnection and installation of the DMS.
Ensure that the wall is strong enough to support the
weight of the DMS.
Must install the DMS with rated power supply.
The DMS must be installed according to
the national electrical rules by an installation specialist.
If you wish to uninstall the DMS, consult an authorized
installation center.
WARNING
CAUTION  Do not use inflammable gases near the DMS.
Do not install the DMS in a location where
it will come into contact with combustible gases,
machine oil, sulphide gas, etc.
Avoid locations where acid/alkali solution or special
spray is used.
Choose a location that is dry and sunny, but not exposed
to direct sunlight. Suitable temperature is between
0°C(32°F) and 39°C(102.2°F).
 Do not spill water into the DMS.
Do not apply tensile strength to the cable to avoid cable
damage.
Do not press the buttons with a sharp object.
Do not connect the power cable to the control terminal.
If the DMS is installed in a hospital or other special
places, it should not affect other electronic devices.
This installation manual describes how to install the DMS. For installation of other
optional accessories, refer to the appropriate installation manual.
MIM-D00_IM_E_29919-1.indd 2 2008-09-10 ｿﾀﾈﾄ 1:27:10

E-3
ENGLISH
Contents
 SAFETY PRECAUTIONS ..................................................................... 2
 BEFORE INSTALLING THE DMS ...................................................... 4
 ACCESSORIES ..................................................................................... 5
 PRODUCT DESIGN ............................................................................ 5
 PRODUCT DIMENSIONS ................................................................... 6
 SYSTEM ARCHITECTURE ................................................................... 7
 COMPATIBLE DEVICES ...................................................................... 8
 INSTALLING THE DMS .................................................................... 9
 DMS EXTERNAL DISPLAY ............................................................. 14
 SETTING THE COMPUTER ENVIRONMENT ...................................... 15
 APPENDIX ......................................................................................... 22
MIM-D00_IM_E_29919-1.indd 3 2008-09-10 ｿﾀﾈﾄ 1:27:10

E-4
Before installing the DMS(Data Management Server)
The following items need to be prepared before installation.
WARNING
• Only static IP must be used for the DMS. (Public IP or private IP)
The DMS is a server and only static IP must be used. To access the
DMS through the internet or with SNET series, the DMS address,
which is the IP address, must be known. A static IP service from an
internet service provider must be used if xDSL (ADSL, VDSL) is being
used for internet connection. (Static IP costs more than dynamic IP.)
Choosing between a private IP and a public static IP depends on
whether the DMS needs to be controlled from an external location.
General DSL service uses dynamic IP and cannot be used with the
DMS. Refer to page 23~24 for explanation on technical terms.
DMS IP
 A public IP is needed to access the DMS over the internet.
(One public IP is needed for each DMS)
 A private IP may be used if the DMS need not be accessed
over the internet.
 The DMS does not support *DHCP.
Note *DHCP(Dynamic Host Configuration Protocol)
  An Internet protocol for automating the
configuration of computers that use TCP/IP.
DHCP is used to automatically assign IP addresses.
In other words, the IP address of the host is supported
only when the PC is on.
NETWORK RELATED EQUIPMENTS
 Network equipments such as HUBs and network cables
are not provided by Samsung.
INSTALLATION NOTICE
 The DMS is recommended to be wall-mounted to prevent
damage to the product and for safety issues.
 The LAN cable and the communication cables(C1,C2)
from the centralized controllers must be installed
in such a way that the wires can be connected to
the DMS with ease.
MIM-D00_IM_E_29919-1.indd 4 2008-09-10 ｿﾀﾈﾄ 1:27:10

E-5
ENGLISH
Accessories
DMS(1) Cable Tie (2) Cable Clamp(3) M4X16 Screw(5)
Rubber Hook(4) User's manual (1) Installation manual (1)
 The DMS must be installed by a trained installer.
 Ensure the main power is turned off before installing
the DMS.
 The power cable and the communication cable must
be installed according to the national electrical wiring
regulations. (VCTF 2C x 0.75mm2 must be used for the
communication and power cables)
 Ensure the cables are out of user’s reach.
Caution
Product Design
MIM-D00_IM_E_29919-1.indd 5 2008-09-10 ｿﾀﾈﾄ 1:27:11

E-6
Product Dimensions
Unit : mm
 Installation Method
Fix the provided screws to the wall and use the four holes on the back of
the DMS to hang the DMS on the wall.
219
150
10 10 10 37
135
135 20
30
60
28
88
130
60
Serial Port
LAN Port
Reset Button
Power Input
MIM-D00_IM_E_29919-1.indd 6 2008-09-10 ｿﾀﾈﾄ 1:27:13

E-7
ENGLISH
System Architecture
Note Products with ‘*’ are not Samsung products and must be
purchased separately.
S-NET 3
* HUB
 Network related
equipments to be
purchased separately
Centralized
Controller
Centralized
Controller
SIM I/M
Transmitter Transmitter Transmitter
* Power meter
Power related
equipments to
be purchased
separately
Connect one power meter to
N number of outdoor units.
Make sure the power meter
capacity is greater than the
total capacity of the outdoor
units.
DMS
MIM-D00_IM_E_29919-1.indd 7 2008-09-10 ｿﾀﾈﾄ 1:27:14

E-8
Compatible Devices
No. Devices Model Note
1Indoor Unit
Outdoor Unit
All System indoor/outdoor units
such as: DVM, DVMH models,
DVM PLUS, DVM PLUS ΙΙ/ΙΙΙ,
MINI DVM, HOME DVM,
CAC models
-
2Interface
Module
MIM-B04A(for DVM, DVM PLUS etc.)
MIM-B13(for DVM PLUS ΙΙ etc.)
MIM-B13A(for DVM PLUS ΙΙ, ΙΙΙ etc.)
-
3Centralized
Controller
MCM-A202
MCM-A202A -
4 SIM I/M MIM-B12 Needed for power distribution
*5 Watt-hour
Meter RS485 comm. type
Needed for power distribution
( Please consult Samsung for
compatible power meters)
Note Products with ‘* ’ are not Samsung products and must be purchased separately.
(Only selected power meters may be used for protocol compatibility issues.)
Maximum Devices attachable
The maximum number of devices attachable to the DMS is as follow:
Devices Max. Note
Centralized Controller 16 Must not exceed 16
Indoor Unit 256 Tracking error occurs if exceeded
SIM I/M 8 -
Watt-hour Meter 64 8 power meters for each SIM I/M
MIM-D00_IM_E_29919-1.indd 8 2008-09-10 ｿﾀﾈﾄ 1:27:16

E-9
ENGLISH
Installing the DMS
Connecting the Centralized Controller
The centralized controllers must be installed to control the
indoor units.
1
Loosen the two screws on the bottom of the DMS front
cover.
2
Hold the bottom two sides of the DMS and push upwards
to slide open the cover. (Sliding type cover)
3
Connect the provided power cable to the power terminal.
4 Connect the C1, C2 communication cable from the
centralized controller to the J1 terminal of the DMS.
(Communication will fail if the cable is not connected
properly.)
5 Connect the LAN cable to the J6 terminal of the DMS.
6Close the case cover after making sure the power cable is
not pressed.
7 Assemble the cover as shown in the picture to avoid
exposure of the stripped wires.
 Maximum 16 centralized controllers can be connected
to one DMS.
 Separate the power cable and the communication cable
when installing the DMS. (The DMS may malfunction
due to electrical disturbance.)
Caution
POWER CABLE
Centralized controller
communication cable
LAN CABLE
MIM-D00_IM_E_29919-1.indd 9 2008-09-10 ｿﾀﾈﾄ 1:27:17

E-10
Installing the DMS (Continued)
Connecting the SIM I/M
The SIM I/M must be used for the power distribution function.
1
Loosen the two screws on the bottom of the DMS front
cover.
2Hold the bottom two sides of the DMS and push upwards
to slide open the cover. (Sliding type cover)
3
Connect the provided power cable to the power terminal.
4 Connect the C1,C2 communication cable from the SIM I/M
to the J1 terminal of the DMS.
(Communication will fail if the cable is notconnected
properly.)
MIM-D00_IM_E_29919-1.indd 10 2008-09-10 ｿﾀﾈﾄ 1:27:19

E-11
ENGLISH
Installing the DMS (Continued)
POWER CABLE
Peak Power I/M
communication cable
LAN CABLE
5 Connect the LAN cable to the J6 terminal of the DMS.
6Close the case cover after making sure the power cable is
not pressed.
7 Assemble the cover as shown in the picture to avoid
exposure of the stripped wires.
 Maximum 8 SIM I/Ms can be connected to one DMS.
 Maximum 8 power meters can be connected to one SIM I/M.
 Separate the power cable and the communication cable
when installing the DMS. (The DMS may malfunction
due to electrical disturbance.)
Caution
MIM-D00_IM_E_29919-1.indd 11 2008-09-10 ｿﾀﾈﾄ 1:27:21

E-12
Installing the DMS (Continued)
DMS PCB Option Switches
1
Reset Switch (SW01) :
Resets the DMS when the DMS stops operating.
(Pressing the reset switch will delete all current data.
The switch must only be operated by the installer.)
2 DIP Switch(SW3) :
Used for setting the DI mode.
Operate only when the DI port is used.
<Factory Default Settings>
SW03
Note Refer to the appendix (page 22~23) for how to install
the DI external signal control.
MIM-D00_IM_E_29919-1.indd 12 2008-09-10 ｿﾀﾈﾄ 1:27:22

E-13
ENGLISH
Installing the DMS (Continued)
Using the DI external contact signal control (Optional)
DIP Switch (SW03) : Use only for external contact signal control.
Pattern DIP Switch Control Details
1 2 3 4
Pattern
1OFF OFF OFF OFF
No response to the external contact signal control.
(Factory default setting)
Pattern
2ON OFF OFF OFF
Used for emergency cases such fire.
 Responds when there is an input signal on DI-1
 Operation:
Turns off all the indoor units when there is an ON
signal input, and disables the use of all the remote
controllers. During an emergency stop,
the DMS will ignore any request from the higher level
controllers. The schedules will not operate as well.
The indoor unit remote controllers will restore to the
status previous to ON signal, when the external input
signal changes to OFF.
Pattern
3OFF ON OFF OFF

Responds when there is an input signal on DI-1 and DI-2.
 Operation:
Changes the on/off status of all the indoor units
depending on the ON/OFF status of the DI-1 input.
Enables/disables the remote controllers depending on
the ON/OFF status of the DI-2 input.
(ON: enable/ OFF: disable)
The schedules will run regardless of pattern 3.
Pattern
4ON ON OFF OFF

Responds when there is a pulse input on DI-1,2.
 Operation:
Turns on all the indoor units when there is a pulse
input on DI-1.
Turns off all the indoor units when there is a pulse
input on DI-2.
Turns off all the indoor units when there is a pulse
input on DI-1, DI-2.
(The pulse width is valid only for 0.5~1.0 sec.)
The schedules will run regardless of pattern 4.
Note Refer to the appendix (page 22~23) for how to install the DI external signal control.
MIM-D00_IM_E_29919-1.indd 13 2008-09-10 ｿﾀﾈﾄ 1:27:22

E-14
DMS External Display
LED Status Display
1
2
3
4
5
6
7
8
9
10
Power (Red) Power display.
The power display is on when there’s a power input.
CPU Alive(Yellow)
Flickers every second if the CPU is operating normally.
(The CPU is in waiting status and the CPU Alive display is off
initially when powered up.)
Linked (Green) Internet cable connection status display.
The display is on when connected to the internet.
Active (Green) Flickers during data transceive.
RS485 Tx (Green)
Flickers during data transmission from the DMS to
the centralized controller.
(Starts flickering once the tracking is complete.)
RS485 Rx (Green) Flickers during data transmission from the centralized
controller to the DMS.
DI 1 Status (Green) Lights on when using the external contact signal control.
(Refer to page 23)
DI 2 Status (Green) Lights on when using the external contact signal control.
(Refer to page 23)
A/C Running
(Green)
DMS status indicator/Running status of indoor unit indicator
You may setup A/C Running LED to indicate either DMS status
or Indoor unit operation.
- DMS status: Green light will flicker every 5 seconds when
DMS operates normally.
- Running status of indoor unit: Solid green light will turn on
when the indoor units operate normally.
(at least 1 indoor unit)
Error (Green) Lights on if there is an error on at least one indoor or outdoor
unit. Also Lights on when there is a communication error.
MIM-D00_IM_E_29919-1.indd 14 2008-09-10 ｿﾀﾈﾄ 1:27:23

E-15
ENGLISH
Setting the Computer Environment
1
The following device and accessory is needed:
 Computer with a LAN Card
 *Cross Cable or a HUB
2
Setting the computer environment.
 Must have Internet Explorer 6.0 or above installed.
Please install the internet explorer 6.0 or above through
Windows Update
 Must have JRE 1.3.1 or above installed JRE can be
downloaded from http://java.sun.com/j2se or
automatically by connecting to the DMS through the
internet.
3 Connection Method (Choose one of the two methods list
below.)
 Connecting the DMS directly to the computer
 Connecting the DMS using a HUB
Note *Cross Cable:
A cross cable is used when connecting two PCs directly.
A direct cable is used to connect the PC to a HUB, and
a cross cable is used to connect between two PCs or
between a PC and a DMS.
The cross cable can be purchased at any computer
stores.
* (Cross Cable)
Computer
HUB
(Direct Cable)
Computer
MIM-D00_IM_E_29919-1.indd 15 2008-09-10 ｿﾀﾈﾄ 1:27:24

E-16
Setting the Computer Environment (Continued)
4
Setting the computer environment to access the DMS for
the first time.
 All the environment of the DMS is set by connecting
to the DMS. In order to access the DMS, the computer
environment must be set as follow:
Choose one of the two methods to access the DMS.
1) Change the computer IP address (Recommended)
Set the network environment of the computer
connected to the DMS as follow:
 Click on the ‘My Network’ icon on the desktop to access the above screen.
Right click and press ‘properties’.
Right click on the ‘Local Area Network’ icon and press ‘properties’.
Select ‘Internet protocol(TCP/IP)’ and press ‘properties’.
2) Run the route command
Start  Run  Type in the following command  Enter
Route add 192.168.0.0 mask 255.255.255.0 *Computer_IP
 The computer IP refers to the IP address of the computer connected or
that is to be connected to the DMS
Type in 192.168.0.1 when using a private IP.
Note Refer to page 24~25 for setting the IP address.
 The default IP setting of the DMS is 192.168.0.2
MIM-D00_IM_E_29919-1.indd 16 2008-09-10 ｿﾀﾈﾄ 1:27:26

E-17
ENGLISH
Setting the Computer Environment (Continued)
Connect to the internet. Run the internet explorer and type in the following address.
http://192.168.0.2
If the connection is successful, the following front page will load.
The DMS will prompt for a user ID and a password as shown above.
The factory default user setting is as follow:
Type in the ID and the password and click on LOGIN.
Change the user setting if needed for security reasons.
admin
1234
MIM-D00_IM_E_29919-1.indd 17 2008-09-10 ｿﾀﾈﾄ 1:27:26

E-18
Setting the Computer Environment (Continued)
The following screen is displayed if the login is successful.
Click on SYSTEM ENVIRONMENT.
MIM-D00_IM_E_29919-1.indd 18 2008-09-10 ｿﾀﾈﾄ 1:27:26

E-19
ENGLISH
Setting the Computer Environment (Continued)
Click on the ‘Edit’ button to change the language settings.
(Default:English)
The system will start up automatically once the language is set.

 Click on the ‘Edit’ button to change the DMS network settings.
The system will start up automatically once the settings are saved.

 Click on the ‘Edit’ button to change the time settings.
Set the time for accurate error time logs and schedule controls.

 Click on the ‘Edit’ button to change the Operation mode of A/C
Running.
- When you click ‘Edit’ button, it will change to ‘Save’ button.
 Select the mode you wish to set.
- DMS status: Green light will flicker every 5 seconds when DMS
operates normally.
- Running status of indoor unit: Solid green light will turn on
when the indoor units operate normally.
(at least 1 indoor unit)
 Click ‘Save’ button.
- Changed setting will be saved.

Note For detail instructions on setting System Environment,
refer to user’s manual.
MIM-D00_IM_E_29919-1.indd 19 2008-09-10 ｿﾀﾈﾄ 1:27:27

E-20
Setting the Computer Environment (Continued)
 Select either the group mode tracking or the room mode tracking.
 Group mode tracking:
Control the indoor units according to the RMC address.
 Room mode tracking:
- Control the indoor units according to the MAIN address of
the indoor units.
- Indoor unit MAIN address and the RMC address will be
displayed.
The message “Tracking...Please wait.” will be displayed while
tracking. Tracking will take at least a few seconds to at most
three minutes.
Tracking
Click on the tracking button once the environment is set.
The above screen will be displayed.
MIM-D00_IM_E_29919-1.indd 20 2008-09-10 ｿﾀﾈﾄ 1:27:27