Samsung MZ-5PA064 User manual

© 2010 Samsung Electronics I

II © 2010 Samsung Electronics
COPYRIGHT ©
Samsung Electronics Co. Ltd.
This material is copyrighted by Samsung Electronics. Any unauthor-
ized reproductions, use or disclosure of this material, or any part
thereof, is strictly prohibited and is a violation under copyright law.
Samsung Electronics reserves the right to make changes in specifica-
tions contained herein at any time and without notice. The information
furnished by Samsung Electronics in this material is believed to be
accurate and reliable at the time of publishing, but Samsung Electron-
ics makes no warranty, whether express or implied, with respect to
anything found herein.
Trademarks and Service Marks
The Samsung Logo is the trademark of Samsung Electronics. Adobe
is a trademark and Adobe Acrobat is a registered trademark of Adobe
Systems Incorporated.
All other company and product names may be trademarks of the
respective companies with which they are associated.

© 2010 Samsung Electronics III
Contents
1 Product Overview 1
Introduction 1
Installation 1
System Requirement 2
Hardware Requirements 2
Software Requirements 2
Setting Up and Configuring Your System 2
2 Using the DOS SSD Firmware Utility 5
Starting DOS SSD Application 5
3 General Observations & Limitations 12
Observations 12
Limitations 13
Appendix A 14
Troubleshooting 14
Appendix B 15
Glossary 15

IV © 2010 Samsung Electronics
PREFACE
Organization of This Manual
This manual is organized as follows:
Chapter 1 Introduction, gives an overview and installation of DOS SSD
Application with FWD Utility.
Chapter 2 DOS SSD FWD UTIL Firmware Tool, gives detail description of
steps about the DOS SSD FWD UTIL firmware download.
Chapter 3 General Observations & Limitations, gives list of DOS SSD
FWD UTIL observations & Limitation of DOS SSD FWD UTIL.
Appendix A Troubleshooting contains some possible questions and
answers.
Appendix B Glossary contains an alphabetical list and description of
terms used in this manual.
Conventions Used in This Manual
The following conventions are used in this manual.
bold Bold text denotes a menu number.
bold italic Bold italic text denotes a hyperlink.

© 2010 Samsung Electronics 1
Chapter 1
Product Overview
Introduction
Samsung SSD Firmware utility will enable users to update firmware on spe-
cific Samsung SSD's connected to the PC/laptop. Users can download this
application which is a fully automated firmware download solution. The fea-
tures of the application are listed below:
1. One step firmware downloads with minimal user interaction.
2. Auto detection of disks that need firmware upgrade.
Installation
This section will provide you with details about the installation of DOS SSD
Application with Firmware Download Utility (SSD-FWD UTIL).

2© 2010 Samsung Electronics
System Requirement
Check that you have the following required items before installing and using
DOS SSD FWD UTIL.
Hardware Requirements
System (Laptop/PC) needs to have at least two drives to update the firmware,
1. SSD drive requiring firmware upgrade
2. DOS Bootable USB drive with DOS SSD-FWD UTIL application
Software Requirements
DOS USB Bootable disk is required with DOS SSD-FWD UTIL Application
and supporting files.
Setting Up and Configuring Your System
Follow the steps below:
1. Create the DOS SSD application with Firmware Utility on DOS bootable USB
drive.
• Install the Samsung SSD Magician application on windows PC.
•StartSSD Magician application, Click Firmware Update menu on
SAMSUNG SSD MAGICIAN application.
OR
Right Click on SAMSUNG SSD MAGICIAN icon on system tray and select
Download New Firmware from the pop-up menu.

© 2010 Samsung Electronics 3
Figure 1: Firmware Update
•Select USB Bootable Disk — Click Browse button to select DOS USB
Disk from the pop-up menu.
•Browse Firmware Update Image — Click Browse button to select the
folder which contains latest firmware’s download from Samsung web-
site.
•ClickStart button. The Progress bar shows USB bootable solution
progress.
Note: The Start button will be disabled and USB boot disk creation
will start.

4© 2010 Samsung Electronics
Figure 1: Firmware Update Solution
• Once the bootable disk creation is complete a message, “USB disk solu-
tion created successfully. Restart the PC and boot from USB for Firm-
ware Update.” is displayed. Click OK to complete the process.
2. Shut down the PC if it’s running any OS.
[Warning]: “DEVICE MUST BE PLUGGED IN AT ALL TIMES DURING
THE FIRMWARE UPDATE PROCESS OR ELSE DRIVE MAY BE
PERMANENTLY DAMAGED AND RENDERED INOPERABLE.”
"YOU MUST BACK UP ALL DATA ON THE DRIVE AS THE
FIRMWARE UPDATE PROCESS WILL CAUSE THE LOSS OF ALL
PRE-EXISTING DATA"
3. Re-boot the PC with DOS SSD FWD UTIL application on DOS bootable USB
drive.
4. DOS SSD application is launched automatically.

© 2010 Samsung Electronics 5
Chapter 2
Using the DOS SSD Firmware
Utility
IMPORTANT: The following section assumes that DOS SSD FWD UTIL has been
properly installed. Before proceeding, be sure to:
Successfully complete the entire DOS SSD FWD UTIL installation
process as instructed in the “Setting Up and Configuring Your
System” on page 2 section
Starting DOS SSD Application
The DOS SSD application is launched from the USB.
[Warning]: DOS SSD FWD UTIL will execute only in IDE/ATA or AHCI
mode. Please check the BIOS setting and set drive mode/
configuration to Native/Compatible/Legacy/AHCI modes.

6© 2010 Samsung Electronics
Follow the steps below:
1. Boot the Laptop/PC in DOS mode from USB Memory device.
2. The DOS SSD application is launched automatically.
3. Press ‘1’ to select ‘Samsung Firmware Download Utility’.
Figure 2: DOS SSD Application
4. After reading the disclaimer, Press [Y] to accept the disclaimer.
5. The application scans for the connected SSDs. The detected disk list is dis-
played for a few seconds.

© 2010 Samsung Electronics 7
Figure 3: Disk Detected
6. The disk details on which firmware have to be downloaded is displayed.
7. A confirmation message, “Do you want to Download Firmware on the
disk?” is displayed.
• Press [Y] to perform the action.
OR
Press [N] to select another disk.

8© 2010 Samsung Electronics
Figure 4: Firmware Download Confirmation
8. Another confirmation message is displayed to continue after backing up
the data.
9. Press [Y] key to perform the action.

© 2010 Samsung Electronics 9
Figure 5: Data Backup Confirmation
10. The Firmware upgrade process will start and a message Downloading
Firmware.... is displayed. Do not operate the system during the upgrade
process.
11. On Successful Completion of Firmware, you will be asked to Power Off /
On the drive. A confirmation message Confirm After Power Off / On? [Y]
is displayed. Follow the steps below in sequence:
Note: Power Off / On message is optional. Depending on the firmware
download type, this message is displayed.
• Unplug the SATA cable from the SSD
• Unplug the power cable

10 © 2010 Samsung Electronics
• Plug the power cable back to SSD.
• Plug the SATA cable.
12. Press [Y] to continue.
13. A confirmation message with the downloaded firmware version is
displayed.
Figure 6: Firmware Download Confirmation
14. After few seconds, the application is closed or it may go to the next SSD.
Note: If the firmware is already downloaded on the SSD, then it will
notify the user.

© 2010 Samsung Electronics 11
Figure 7: Firmware Notification

12 © 2010 Samsung Electronics
Chapter 3
General Observations &
Limitations
This section provides with a list of DOS SSD FWD UTIL Observations & Lim-
itations.
Observations
1. If the disk is unplugged during the firmware download process, the results
are unpredictable.
2. The USB that has DOS SSD-FWD UTIL executable, firmware binaries and
DOS bootable files should remain connected to the PC when SSD-FWD UTIL
is running.
3. Accessing the disk while firmware download operation is in progress may
give unpredictable result.

© 2010 Samsung Electronics 13
4. This application should be used only with authorized Samsung SSD for the
intended purpose of upgrading firmware.
5. It is a good practice to take a backup of the data before starting firm- ware
download process.
6. When DOS SSD firmware download solution is not available then, an error
message, “Firmware download solution not available. Please create it
using Samsung SSD Magician Tool.” is displayed. Then end user has to per-
form Firmware update using SSD Magician tool.
Limitations
1. AHCI or ATA mode must be enabled in the BIOS during PC boot up. The DOS
SSD application automatically senses the mode and works accordingly.
2. Removal of disks when the application is running on PC’s with chipsets such
as ICH5/6 that do not support hot plug feature, may cause the DOS SSD
FWD UTIL utility to hang and a system reboot is needed.
3. DOS SSD Application cannot render the FONT correctly on some of the Dis-
play chipset like Intel® Q45/Q43 Express Chipset.
4. DOS Drivers cannot detect the SSD connected to system when the BIOS are
set to “RAID ON”.
5. SSD FWD Utility is not supported in AHCI mode on AMD chipset.

14 © 2010 Samsung Electronics
Appendix A
Troubleshooting
Q 1: Why DOS SSD FWD UTIL application is taking long time to
open?
A 1: SSD tries to detect disks connected to the system when it is
launched. This may require few minutes depending on the num-
ber of disks connected to the system and the hardware platform.
Q 2: Why DOS SSD-FWD UTIL application does not download
firmware, but returns a success?
A 2: Initial firmware may have been downloaded onto the SSD and it
may not have been Power Off / On by the user.

© 2010 Samsung Electronics 15
Appendix B
Glossary
AHCI
AHCI is an acronym for Advanced Host Controller Interface. It is a speci-
fication that allows software to communicate with Serial ATA devices. In
other words it is a hardware mechanism describes the register-level
interface for a Host Controller for Serial ATA. NCQ support is also pro-
vided by AHCI.
ATA
ATA Stands for Advanced Technology Attachment. It is a type of disk drive
that integrates the drive controller directly on the drive itself.
Boot Disk
A boot disk is a DOS based bootable USB solution that contains DOS SSD-
FWD UTIL application and relevant files. Using relevant tools and
procedures in windows environment, the boot USB can be created to launch
DOS SSD-FWD UTIL application in DOS.

16 © 2010 Samsung Electronics
Power Off / On
There are two ways to Power Off/On.
1. Turn Off the system and turn on the system.
2. Unplug the SSD from the system and plug the SSD to the system.
SSD
A Solid State Drive (SSD) is a data storage device that uses solid-state mem-
ory to store persistent data.
USB
USB (Universal Serial Bus) is a popular hardware interface that allows
users to attach secondary hardware devices to their computer in a Plug-
and-Play fashion.