Samsung TC-9015VP User manual

Operating
Instructions
TC-9015VP
❈
FOR HOUSEHOLD USE ONLY
TC-9015VP(DJ68-40015E) 8/9/01 8:39 AM Page 1

1
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
To reduce the risk of fire, electric shock, of injury:
1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before
servicing.
2. Do not use outdoors or on wet surfaces.
3. Do not allow to be used as a toy. Close attention is necessary when used by or near children.
4. Use only as described in this manual. Use only manufacturer’s recommended attachments.
5. Do not use with damaged cord or plug. If appliances is not working as it should, has been
dropped, damaged, left out door, or dropped into water, return it to a service center.
6.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around
sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces
.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Do not handle pulg or appliance with wet hands.
9. Do not put any object into openings. Do not use with any opening blocked ; keep free of
dust, lint, hair, and anythin that may reduce air flow.
10. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
11. Do not pick up anything that is burrning or smoking, such as cigarettes, matches, or hot ashes.
12. Do not use without dust bag and filters in place.
13. Turn off all controls before unplugging.
14. Use extra care when cleaning on stairs.
15. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas
where they may be present.
16. Hold plug when rewinding onto cord reel. Do not allow plug to whip when rewinding.
17. This hose contains electrical connections.
18. Do not use to suck up water.
19. Do not immerse in water for cleaning.
20. The hose should be checked regularly and must not be used of damaged.
21.
The plug must be removed from the socket - outlet before cleaning or maintaining the appliance.
22. If the supply cord is damaged, it must be replaced by a special cord or assembly available
from the manufacturer or its service agent.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
TC-9015VP(DJ68-40015E) 8/9/01 8:39 AM Page 2

If the “Dust - Full” indicator switches to “RED” while you are cleaning, the dust bag requires
relacement.
2
DUST-FULL INDICATOR
HANDLE
SUCTION HOSE
CORD REWIND
BUTTON
POWER CONTROL
SWITCH
ON / OFF BUTTON
TOOL STORAGE
COVER
CLAMPER FOR DUST BAG
COMPARTMENT
BUTTON FOR SUCTION
HOSE REMOVAL
DUST-FULL
INDICATOR
HANGER
TUBE
RUG / FLOOR SELECTOR
FLOOR NOZZLE
NOTE
If the “Dust - Full” indicator continues to display “RED” even after changing
the dust bag turn the cleaner off and check whether the hose, tube or nozzle
is clogged.
IDENTIFICATIONS PARTS
TC-9015VP(DJ68-40015E) 8/9/01 8:39 AM Page 3

3
1) Connect the suction hose to the suction
tube.
3) Connect the nozzle to the suction tube.
1) PULLING OUT
The power cord is long enough to be
drawn out for a convenience.
2) REWINDING
Upon finishing cleaning disconnect the plug
from the electrical outlet and just press the
cord rewind the button lightly with your toe.
With the cord plugged into an electrical
outlet, start or stop the vacuum cleaner by
stepping lighty on the switch button.
2) Connect the suction tubes together.
4) Connect the hose clamper to the body
of the clamper along the arrow point.
ASSEMBLING THE VACUUM-CLEANER READY FOR USE
POWER CORD
ON / OFF SWITCH
NOTE
When removing the power cord from the electrical outlet, grasp the plug, not the cord.
TC-9015VP(DJ68-40015E) 8/9/01 8:39 AM Page 4

4
The suction power can be adjusted with the
electrical power control to suit any situation.
MIN = For delicate fabrics, like net curtains.
MAX = For hard floors and heavily soiled carpets.
 Dusting brush - for furniture, shelves,books,
etc.
 Upholstery brush - for cushions and drapery.
 Crevice tool - for radiators, crevice, corners,
between cushions.
 Brush head -
The rotating brush ensures that cleaning is
carried out more thoroughly.
Push the switch(A) down.
(The brush switches on)
Located in the top rear side of the vacuum
cleaner, there is a support for a convenient park
position during pauses when using the nozzle.
POWER CONTROL
USING THE ACCESSORIES
OPEARATING THE BRUSH HEAD
PARK POSITION
MAX
MIN
A
SLIDING REGULATOR
TC-9015VP(DJ68-40015E) 8/9/01 8:39 AM Page 5

5
For easy storage and transportation, this
vacuum cleaner has a clip system built onto
the body, which will keep the tube, hose
and nozzle in a vertical position.
1) To open the dust cover of the dust bag
compartment press the clamper upward
located at the side of the dust cover.
3) After removing the used dust bag, insert
the cardboard bag collar of the new dust
bag in to the suction inlet to the full.
2) Remove the dust bag from the cleaner.
4) Press the dust cover down gently until
the clamper relocks.
TRANSPORTING AND STORING THE VACUUM CLEANER
REPLACING THE DUST BAG
BRUSH HEAD
NOTE
After using the cloth filter bag is
full, clean the cloth filter bag and
use it again.
NOTE
Used dust bag can be sealed by
removing th film from the paper
and sticking the latter over the
suction opening.
You can change or clean the brush by removing
the cover, having first detached it with the 2 slides.
Remove the brush from the plastic guides and
toothed belt and clean, or insert a new brush.
Do not lose the plastic guides, washers or springs.
TC-9015VP(DJ68-40015E) 8/9/01 8:39 AM Page 6

6
The rubber lip under the brush head can be
removed if it requires cleaning or replacing.
Lift the rubber lip in the middle and pull out of
the guides at one side.
The motor filter situated between the dustbag
and the motor wil gradually become dirty.
Each time you change the air outlet filter we
advise you to remove the motor filter and to
clean it by tapping to remove the dirt and then
replacing it in the vacuum cleaner.
The microfilter filters the air which comes out
from the vacuum cleaner.
To open the filter cover, press down and pull it
simultaneously.
Remove and replace the exhausted microfilter.
Close the cover.
CARE OF MOTOR FILTER
REPLACING THE MICROFILTER
TROUBLESHOOTING
PROBLEM CAUSE REMEDY
Motor does not start
Suction force is gradully
decreasing
Cord does not rewind fully
No voltage
Filter, nozzle, suction hose
or tube blocked.
Check that the cord is not
twisted or wound unevenly
Check cable, plug and socket.
Remove the object.
Pull the cord ot 2~3m & push
down the cord rewind button
TC-9015VP(DJ68-40015E) 8/9/01 8:39 AM Page 7

This Vacuum cleaner is approved the following
EMC Directive : 89/336/EEC, 92/31/EEC and 93/68/EEC
EN 61000-3-2 : 1995, EN 55014 : 1993 and EN 55104 : 1995
Low Voltage Safety Directive : 73/23/EEC and 93/68/EEC
IEC 335-1, IEC 335-2-2, EN 60335-1 and EN 60335-2-2
CODE NO.DJ68-40015E
TC-9015VP(DJ68-40015E) 8/9/01 8:39 AM Page 8