Samwontech Nova Series User manual

Instruction Maunal

Contents
1. Safety Guide 3
2. Control Keys and Display 5
5. Setting Up Parameter in each Group
6
5.1 Input Group(G.IN) 9
5.2 Output Group(G.OUT) 13
5.5 PID Group(G.PID) 21
5.6 Auto Tuning Group(G.AT) 25
5.7 Alarm Group(G.ALM) 27
5.8 Retransmission Group(G.RET) 30
5.9 Communication Group(G.COM) 31
3. Parameter Map
9
6. Display Error and Correction 33
7. Installation 34
7.1 Dimension and Panel Cutout
7.2 How to install Mount 39
7.3 Power Cable Specification 40
7.4 Terminal Specification 40
7.5 Terminal Arrangement and External Wiring 41
34
4. Flow of Operating Display 8
5.3 Control Group(G.CTL) 16
5.4 SP Group(G.SP) 19

7.7 Analog Input Connection
7.8 Analog Output Connection 47
7.9 External Contact Output Connection(RELAY) 48
7.10 External Contact Input Connection(DI) 48
7.11 Use an Auxiliary Relay 48
7.12 Communication Wiring(RS485) 49
46
Attach. Table of D-Register 50
7.6 Grounding and Power Cable Connection 46
Table 1 : Type of Input Sensor 9
Table 2 : DI Operation 16
Table 3 : Type of Alarm 28
Fig 2 : Example of Piece Bias Formula 11
Fig 3 : Example of Control Output (CT = 10 sec) 14
Fig 4 : Reserve Function of Running 16
Fig 5 : Overshoot Suppressing by Fuzzy Function 21
Fig 6 : Ex. Both Heat and Cool is under PID Control 23
Fig 7 : Ex. Heat = ON/OFF, Cool = PID Control 23
Fig 8 : Ex. Heat = PID, Cool = ON/OFF 24
Fig 9 : AUTO TUNING 25
Fig 10 : AT GAIN 26
Fig 11 : Alarm Operation 28
Fig 1 : Example of Piece Bias 11

(1) This Manual should be passed on the end User and keep a suitable place for operator to
study and check the function of the product.
(2) Operator should carefully study, understand how to operate this product before
(3) This manual is describing the functions of the product. We, Samwontech, does not warrant
that the functions will suit a particular purpose.
(4) Under absolutely no circumstance may the contents of this manual in part or in whole be
transcribed or copied without permission.
(5) All contents of this manual has been made to ensure accuracy in the preparation, However,
should any errors or omissions come to the attention of the user, feel free to contact our
sales representatives or our sales office
(1) In order to protect this product and the system controlled by it against damage and ensure
its safe use, make certain that all of the safety instructions and precautions in this manual
are strictly adhered to.
(2) We, Samwontech, are not guarantee safety if the products are not handled according to
this instruction manuals
(3) If separate protection or safety circuits are to be installed for this product or the system
which is controlled by this product, ensure that such circuits are installed external to the
product.
(4) Don’t try to make modifications or additions internal to the product. It may becomes
electric shock, burn or out of order.
(5) In case of replacement parts or consumables of the product, must call to our sales office.
(6) Protect this product from moisture. It may becomes out of order.
(7) Protect any kind of shock and vibration to the product. It may becomes product defects
and out of order
(1) Samwontech co. Ltd does not make any warranties regarding the product except Warranty
conditions those mentioned in this manual.
(2) We assumes no liability to any party for any loss or damage, direct or indirect, caused by
the use or any unpredictable defect of the product.
The following safety symbols are used in this manual
(A) If this symbol is marked on the product, the operator must investigate the explanation given in this
manual to protect injury or death to personnel or damage to instrument.
(1) For Production : it should be marked when operator must refer the explanation in the
manual to avoid loss of life or damage to instrument.
(2) For Instruction Manual : it marks to avoid operator’s loss of life and injury that may result
comes from Electric Shock.
(B) Functional earth terminal Equipment protected by double or reinforced insulation
It marks the terminal must be connected to Ground prior to operating the equipment.
(C) It marks additional Information on the operation and features of the product.
(D) It marks for further information on the current topic and pages

(1) Be sure to operate the controller installed on a panel to prevent electric shock.
(2) To install the controller, do select a location where;
■ No one may accidentally touch terminal.
■ Mechanical vibrations are minimal.
■ No corrosive gas is prevent.
■ Temperature fluctuation is minimal.
■ Temperature can be maintained. (50 ℃ below / 10 ℃ over)
■ No direct heat radiation is present.
■ No magnetic disturbances are caused
■ No water is splashed.
■ No flammable materials are around.
■ No wind blows. (prevent Dust with salt)
■ No ultraviolet rays are present.
■ Pollution Degree 2
■ Installation Category II
■ Do not block openings
■ If the equipment is used in a manner not specified by the manufacturer,
the protection provided by the equipment may be impaired.
■ A switch or circuit-breaker acting as the disconnect device shall be included in the
application or the building installation
■ Keep the input circuit wiring as far as possible away from power and ground circuit.
■ Keep the controllers in 10℃ ~ 50℃/ 20 % ~ 90 % RH,
Warming up needed to use controller when temperature is below 10℃ in advance.
■ Do not mount front panel facing downward.
■ To prevent electric shock, be sure to turn off and the source circuit breaker before wiring.
■ The power consumptions are 100-240VAC, 50/60Hz, 10VAmax and operate without power
switching in advance.
■ No work in wet hands ( it caused electric shock)
■ Follow operation by precaution in the manual to avoid fire, electric shock, loss of life etc.
■ Requested to follow mounting and operation methods just indicated in this manual.
■ Refer the way of grounding connection, however, keep away for grounding to Gas pipe,
water pipe, lightening rod etc.
■ Be sure not to power connection before finishing of wiring between each contact point.
■ Not close and wrapping the heat hole in back case of controller.
(1) The guaranteed period of the production quality assurance is (1) one year after end user
buy it and it will be free to fix defected product under regular usage described
by this manual.
(2) It will be charged to fix defected product after warranty period. This charge will announced
by our actual cost to be calculated during the fixing time.
(3) It will be charging even if within warranty period as following events.
(3.1) Defect by operator and user’s default.(forget password, production initialize)
(3.2) Natural disaster.(fire, water flow etc)
(3.3) Additional shift after 1st installed.
(3.4) Improperly repaired, or altered, modified in anyway.
(3.5) Power failure in unstable power condition.
(4) Feel free to contact our sales office whenever it need to make A/S.

LED Contents
SP2,3,4
EV1,2,3
OUT
MAN
- Lights on during SP operation.
- Lights on during EVENT occurs.(such as signal occur for alarm)
- Lights on when Control Output occur.
- Lights on when Manual Mode operates.
Or, LED blinking during AUTO-TUNING process.
⊙ Control Keys
⊙ LED Display
KEY Contents
- Used in switching between parameters or registering parameter settings.
- Pressing SET/ENT Key at least 3 sec. switches between an operating display
and an operating parameter setting display
- Used to change the value of parameters.
- Used to move between GROUP and change SP value.
- Used when shifting position to modify value.
▲／▼
(UP/DOWN)
◀ (SHIFT)
SET/ENT
(ENTER)

* : When I=0, When H/C, all time indicate
: OPTION
** : When type of OUT2, 3 is Heat or Cool
*** : Option display for ST570, ST540
**** : No Option in ST540
: H/C Type
AT
AT-G
A
ARW
FUZY
PID
1.P
1.I
1.D
1.MR
1.RP
2.P
2.I
2.D
2.MR
PID=1 PID=2
**
▲▼
S-TM
P-TM
A/M
U.PWD
US1
US2
LOCK
DI.SL
OSTS
PWD
G.PID G.CTL
DSP.H
R-S
SPSL
SP1
SP2
SP3
SP4
SPRH
TMU
U.SLP
D.SLP
G.SP
G.AT
1.Pc
1.Ic
1.Dc
1.DB
2.Pc
2.Ic
2.Dc
2.DB
DSP.L
INIT
▲▼
▼
SPRL
▲▼
SET/ENT SET/ENT SET/ENT SET/ENT
ONOF
3.P
3.I
3.D
3.MR
RHY
4.P
4.I
4.D
4.MR
PID=3 PID=4
**
3.Pc
3.Ic
3.Dc
3.DB
4.Pc
4.Ic
4.Dc
4.DB
2.RP RDV
C.MOD

OUT1
OUT2 HEAT
OUT3
▲▼
HEAT
SUB1
SUB2
O.ACT
CT
OH
OL
PO
G.OUT
ALT1
AL-1
A1DB
ALT2
▲▼
G.ALM
RET
RETH
RETL
▲▼
G.RET
COM.P
BAUD
PRTY
▲▼
SBIT
DLEN
ADDR
RP.TM
G.COM
AL-2
A2DB
ALT3
AL-3
AL3.H
▼
A
COOL
COOL
**
POc
HYS
CTc
A1DY
A2DY
AL3.L
***
****
**
SET/ENT SET/ENT SET/ENT SET/ENT
IN-T
IN-U
IN.RH
IN.RL
G.IN
IN.DP
IN.SH
IN.SL
IN.FL
BSL
RSL
BSP1
BSP2
BSP3
BS0
BS1
BS2
BS3
BS4
SET/ENT
HYS.H
HYS.L
*****
*****
A3DB
A3DY
AL2.H
AL2.L
AL1.H
AL1.L
D.FL
O.LED
RBS

ENT
ENT
ENT
▼
When setting the controller,
parameter G.IN and G.Out
should be setting up prior to
any others
US1,US2 can be setting up
by Operator for modifying
parameters and set up in
G.CTL refer to Table of
D-Register as attached
in this manual
ENT
H.OUT Value
……
▼ or ▲
(*note 1: Display ‘STOP’ when operates stopping.)
- it can be able to change SP Value when STOP operates)
(*note 2: Operation Display-1 : Initial display after power on ; can set SP value.)
(*note 3: Operation Display-2 : Output Control Display.)
(*note 4: Heating Output Display in H/C type.)
(*note 5: Cooling Output Display in H/C type.)
(*note 6: When User Screen-1 is registered.)
(*note 7: When User Screen-2 is registered.)

5.1 Input Group(G.IN)
Press SET/ENT Key to select input group after press ▲ or ▼ Key in Menu
display. (Refer to parameter Map in chapter 3.)
The parameter to select type of temperature sensor and its initial setting is
type TC,K1.
Refer to following ‘Table of Input Sensor’ and select No shown in Table 1.
Change setting up parameters should be done for the first stage because it is
suspended initializing parameters in other group around.
G.AT ↔ G.SP ↔ G.PID ↔ PWD ↔ G.CTL ↔
↑ ↕
G.COM ↔ G.RET ↔ G.ALM ↔ G.OUT
▲▼ ▲▼ ▲▼
▲▼ ▲▼
▼
▲▼
▲▼
▲▼
▲▼
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
15
16
17
18
19
20
21
22
23
24
TYPE
K1
K2
J
E
T
R
B
S
L
N
U
W
Platinel Ⅱ
PtA
PtB
PtC
JPtA
JPtB
0.4∼2.0V
1∼5V
0∼10V
-10∼20mV
0∼100mV
Temp.Range(℃)
-200∼1370
-199.9∼999.9
-199.9∼999.9
-199.9∼999.9
-199.9∼400.0
0∼1700
0∼1800
0∼1700
-199.9∼900.0
-200∼1300
-199.9∼400.0
0∼2300
0∼1390
-199.9∼850.0
-199.9∼500.0
-19.99∼99.99
-150.0∼150.0
-199.9∼500.0
Temp.Range(°F)
-300∼2500
0∼2300
-300∼2300
-300∼1800
-300∼750
32∼3100
32∼3300
32∼3100
-300∼1600
-300∼2400
-300∼750
32∼4200
32∼2500
-300∼1560
-199.9∼999.9
-4.0∼212.0
-199.9∼999.9
-199.9∼300.0
0.400∼2.000V
1∼5V
0∼10V
-10∼20mV
0∼100mV
Group
T/C
RTD
DCV
mV
DISP
TC.K1
TC.K2
TC.J
TC.E
TC.T
TC.R
TC.B
TC.S
TC.L
TC.N
TC.U
TC.W
TC.PL
PTA
PTB
PTC
JPTA
JPTB
2V
5V
10V
20M
100M
14 C0~2320 32∼4200 TC.C

The parameter to select type of temperature unit for ℃ or ℉.
Its initial selection is ℃ type.
Refer to Table 1 when change temperature unit.
The parameter to set High-Limit for input temperature measuring range.
The parameter to set Low-Limit for input temperature measuring range.
The parameter to set the position of decimal value in case that sensor type is
mV or V. The position if decimal value can change 0 ~ 3.
its initial set value is ‘1’.
The parameter to set High-Limit of input measuring scale in case that sensor
type is mV or V.
its initial value of ‘In.SH’ is ‘100.0’
The parameter to set Low-Limit of input measuring scale in case that sensor
type is mV or V.
its initial value of ‘In.SL’ is ‘0.0’
The parameter to set PV filter for stabilizing from electromagnetic noise etc.
it may effect violation of PV value. Its initial value of ‘In. FL’ is OFF and
can change 1 sec to 120 sec.
The parameter to set a direction of PV operation when sensor open. When set
value of BSL is ‘UP’, PV operation is for High-Limit of Input Sensor.
When set value of BSL is ‘DOWN’, PV operation is for Low-Limit of Input
Sensor. Its initial setting is ‘UP’ (* in case of mV, V input, initialize ‘OFF’ and
No checking Sensor-Open in 10V, 20mV, 100mV
The parameter to set whether using RJC or not in case that input sensor is
thermocouple. Its initial setting of ‘rSL’ is ‘ON’
The parameter to set range of Bias in PV value enabling Bias process.
Bias range can set Max 4. for further information, refer to Fig 1. and Fig 2.
The parameter to set Bias value of PV in Bias range.
For further information, refer to Fig 1. and Fig 2.
The parameter to set for decreasing when PV is unstable due to senstive
sensor response under normal control.
.
.
.
.
.
.

Ex) There are +2℃ in 25℃, -1℃ in 50℃, +3℃ in 75℃ as temperature deviation in measuring
actual temperature in range from 0℃ to 100℃, and try to take a Piece Bias, each Bias set
value are shown as belows(RL=0℃, BSP1=25℃, BSP2=50℃, BSP3=75℃, RH=100℃)
BS0=0℃, BS1=-2℃, BS2=+1℃, BS3=-3℃, BS4=0℃
Temperature Bias Value = Temperature after Bias - Actual Temperature
Temperature in 600℃(P) after Bias
BS3 - BS2
BSP3 - BSP2
P = 600 + (600-BPS2) X + BS2
Actual
Temperature
Temperature
after Piece Bias
BS0=0
BS1=10
BS2=10
BS3=50
BS4=0
BSP1=100 BSP2=500 BSP3=800RL=0 RH=1000
600℃
P
:Actual
Temperature
after Bias
BS0
RL BSP3 RHBSP1 BSP2
Actual Temperature
Temperature
after Bias
BS1
BS2
BS3
BS4

Sym Parameter Setting Range Unit Initial Remark
(note 1) : S.OPN(Sensor-Open)=BOUT(Burn-Out)
IN-T Input Type Refer to Table 1 Type of Input Sensor ABS TC.K1 All time
indicate
IN-U Display Unit ℃ / °F ABS ℃T/C, RTD
IN.RH
Max. Value of
Measurement
Range Within DEF. Range refer to Table 1
however, INRH > INRL
EU 1370 All time
indicate
IN.RL
Min. Value of
Measurement
Range
EU -200 All time
indicate
IN.DP Decimal Point
Position 0∼3 ABS 1mV, V
IN.SH Max Value
of Input Scale
Within -1999∼9999
however, INSH > INSL
The Decimal Point Position is relay on
the value of IN.DP
ABS
100.0 mV, V
IN.SL Min Value
of Input Scale 0.0 mV, V
IN.FL PV Filter OFF, 1∼120 sec OFF All time
indicate
D.FL Display Filter OFF, 1∼120 sec OFF All time
indicate
BSL BOUT SEL
(note1) OFF, UP, DOWN ABS UP (DCV=OFF)
All time
indicate
RSL RJC SEL ON, OFF ABS ON T/C
BSP1 Reference
Bias Point1
EU(0.0∼100.0%),
RL BSP1 BSP2 BSP3 RH EU EU(100.0%) All time
indicate
BSP2 Reference
Bias Point2
EU(0.0∼100.0%),
RL BSP1 BSP2 BSP3 RH EU EU(100.0%) All time
indicate
BSP3 Reference
Bias Point3
EU(0.0∼100.0%),
RL BSP1 BSP2 BSP3 RH EU EU(100.0%) All time
indicate
BS0 Bias Value for
RL Point EUS(-100.0∼100.0%) EUS 0All time indicate
BS1 Bias Value for
BSP1 Point EUS(-100.0∼100.0%) EUS 0All time indicate
BS2 Bias Value for
BSP2 Point EUS(-100.0∼100.0%) EUS 0All time indicate
BS3 Bias Value for
BSP3 Point EUS(-100.0∼100.0%) EUS 0All time indicate
BS4 Bias Value for
RH Point EUS(-100.0∼100.0%) EUS 0All time indicate

5.2 Output Group(G.OUT)
Press SET/ENT Key to select Output Group after press ▲ or ▼ Key in Menu
display.
The parameter to set operation of output control (OUT 1 :RELAY OUTPUT)
Value set in Heat, COOL, ALM1, ALM2, ALM3, RUN. Its initial setting is ‘ALM1’
(COOL is displayed in H/C Type, SKIP when ON/OFF Mode select)
The parameter to set operation of output control (OUT 2 : 4~20mV or
Pulse Output). Value set in ‘HEAT, COOL, RET’. Its initial setting is ‘HEAT’.
(COOL is displayed in H/C Type)
The parameter to set operation of output control (OUT 3: 4~20mV or Pulse
Output). Value set in ‘HEAT, COOL, RET’. Its initial setting is ‘RET’. (COOL is
displayed in H/C Type) (* ST570/540 can display when option select)
The parameter to set a type of control output when OUT 2 or OUT 3 sets in
‘HEAT’. Value set in ‘SSR (Pulse Output), SCR ( 4~20mV)’.
Its initial setting is ‘SSR’.
The parameter to set the operation of Auxiliary Output Control (SUB 1: Relay
Output). Value set in ‘HEAT, COOL, ALM1, ALM2, ALM3, RUN’. Its initial setting
is ‘ALM2’. (COOL is displayed in H/C Type) (* Display when option selects)
The parameter to set the operation of Auxiliary Output Control (SUB 2: Relay
Output). Value sets in ‘HEAT, COOL, ALM1, ALM2, ALM3, RUN’. Its initial
setting is ‘ALM3’. (COOL is displayed in H/C Type) (* Display when option
selects, However no option in ST540)
※ Setting example of Output :
Control Output (OUT2 → SSR), Retransmission Output (OUT3 → RET), RELAY Output (OUT1 → ALM1,
SUB1 → ALM2, SUB2 → ALM3)
The parameter to set a type of control output when OUT 2 or OUT 3 sets in
‘Cool’. Value set in ‘SSR (Pulse Output), SCR ( 4~20mV)’.
Its initial setting is ‘SSR
G.AT ↔ G.SP ↔ G.PID ↔ PWD ↔ G.CTL ↔ G.IN
↑ ↕
G.COM ↔ G.RET ↔ G.ALM ↔
▲▼ ▲▼ ▲▼
▲▼
▲▼
▼
▲▼
▲▼
▲▼
▲▼

The parameter to set Reverse or Forward operation of Control Output.
If ‘O.Act’ sets Reverse operation and PV value is lower the SP value, The
control output is ON(Relay) or increase control output(SSR,SCR)
If Forward operations, it works reverse. Its initial setting is ‘REV’.
To set High-Limited value of Control Output.
The parameter to set Hysteresis in case of On/Off Control Output in H/C type.
The parameter to set one cycle time of control ON/OFF when control output
sets up Time-proportional control output. Its setting range is 1 ~ 1000 sec
and ‘2’ sec as initial setting.
To set Low-Limited Value of Control Output.
Control Output is limited within High and Low limited value.
(Fig 3 : Example of Control Output in CT = 10 Sec)
3 Sec
CT=10 Sec
5 Sec
Output=50% Output=70% Output=30%
5 Sec 7 Sec 3 Sec 7 Sec
CT=10 Sec CT=10 Sec
In Case that the cooling control output sets Time-proportional PID in H/C Type
(Ex. OUT 1 =Cool, OUT 2,3 = Cool & Cool = SSR, SUB 1,2 = Cool),
the parameter to set 1 cycle time for Output ON/OFF.
Setting range is ‘1 ~ 1000 sec’. Its initial setting is ‘2 sec’.
The parameter to set Hysteresis High in case of On/Off Mode OUT1RLY Output
in Normal type.
The parameter to set Hysteresis Low in case of On/Off Mode OUT1RLY Output
in Normal type.

(*note 1) : All time indicate (ST570, 540 is Option)
(*note 2) : Option (ST540 is SKIP)
※ Cool type will not workable at H/C Type.
※ OUT1, OH, OL is SKIP in ON/OFF Mode.(OUT1 is RLY control output)
The parameter to set Preset Output value for emergency output.
It makes output value in ‘Po’ after stopping control output calculated
by PID algorithm when stop or A/D Error, Sensor open.
The parameter to set Preset Output value for emergency cooling output in
H/C type. It makes a output set by Poc, it stops to make output by PID
calculation when stopping ,A/D ERROR or Sensor Open in AUTO Mode.
The parameter to set operation of MV OUT LAMP.
SSR : MV LAMP is blinking within CT when SSR or Relay control output.
SCR : MV LAMP is blingking irrespective of CT when SCR control output.
Sym Parameter Setting Range Unit Initial Remark
SUB2
O.ACT
CT
OH
OL
PO
Select Output HEAT, COOL, ALM1, ALM2, ALM3, RUN ABS ALM3 (*note 2)
Reverse and
Forward REV, FWD ABS REV All time indicate
Cycle Time 1 1 ∼ 300 sec sec 2 sec All time
indicate
High-Limit value
of Output
OL-L+1Digit ∼ 105.0%
HC Type : 0 ~ 105.0%, However OH>OL %100.0% All time
indicate
Low-Limit value
of Output
-5.0% ~ OL-H-1 digit
HC Type : 0 ~ 105.0%, However OH>OL %0%
H/C:100.0%
All time
indicate
Preset Out1 -5.0 ∼ 105.0%
H/C Type : 0.0 ~105.0% %0.0% All time
indicate
OUT1
OUT2
OUT3
HEAT
SUB1
Select Output HEAT, COOL, ALM1, ALM2, ALM3, RUN ABS ALM1 All time
indicate
Select Output HEAT, COOL, RET ABS HEAT All time
indicate
Select Output HEAT, COOL, RET ABS RET (*note 1)
Select Ouput
Type SSR, SCR ABS SSR When OUT 2,
3 is in ‘HEAT’
Select Output HEAT, COOL, ALM1, ALM2, ALM3, RUN ABS ALM2 Option
COOL Select Ouput
Type SSR, SCR ABS SSR When OUT 2,
3 is in ‘Cool’
CTc Cycle Time 2 1 ∼ 300 sec sec 2 sec H/C TYPE
POc Preset Out2 0.0∼105.0% %0.0% H/C TYPE
0.0 ∼ 10.0% %0.5% H/C TYPE
HYS.H HYSTERESIS
HIGH EUS(0.0∼10.0%) EUS EUS(0.5%) ON/OFF MODE
HYS.L HYSTERESIS
LOW EUS(0.0∼10.0%) EUS EUS(0.5% ON/OFF MODE
HYS HYSTERESIS
O.LED OUTPUT LED SCR, SSR ABS SSR All time
indicate

5.3 Control Group(G.CTL)
Press ‘SET/ENT Key to select Control Group after press ▼ or ▲ Key in Menu
display.
The parameter to set User Screen for display, confirmation and common use of
parameter. In order to register US1, 2, refer to the parameter number in
‘Table of D-Register.
Its initial setting of US1, 2 is ‘OFF’.
The parameter to set parameter display for common using or checking.
If LOCK sets ‘ON’,prohibit to set all parameter and SP value in operation
display as well.
G.AT ↔ G.SP ↔ G.PID ↔ PWD ↔ ↔ G.IN
↑ ↕
G.COM ↔ G.RET ↔ G.ALM ↔ G.OUT
▲▼ ▲▼ ▲▼
▲▼
▼
▲▼
▲▼
▲▼
▲▼
DI.SL DI1 DI2 Operation
Table 2 : DI Operation
▲▼
The parameter to set waiting time for Running when reserve function sets.
‘S-TM’ can set Max 99.59 min. Its initial setting is ‘OFF’
Refer to Reserve Function of Running shown as Fig. 4
The parameter to set running time of controller. ‘P-TM’ can set Max 99.59
min. Its initial setting is ‘OFF’
Refer to Reserve Function of Running shown as Fig. 4
The parameter to set control mode. (AUTO or Manual)
the Main LED lights on when ‘A/M’ sets MAN, Control output value can set by
Pressing key-input. Its initial setting is ‘AUTO’
OFF - - No work
1
off -HOLD OFF
on -HOLD ON
-off STEP OFF
-on STEP ON
2
off -RESET
on -PROG RUN
-off PROG1
-on PROG2

The parameter to display control output status (OUT1, 2, 3, SUB 1, 2) of the
controller to the operation display.
You can check the control output status in operation display if ‘oStS’ sets.
The parameter to set High-Limited value display of Sensor Input in PV display
window. PV display window only shows the value of DSP.H even if it sets value
higher than DSP.H from the sensor. But controller operates in actual value
The parameter to set Low-Limited value display of Sensor Input in PV display
window. PV display window only shows the value of DSP.L even if it sets value
higher than DSP.L from the sensor. But controller operates in actual value
The parameter to set PASSWORD in Controller. Set U/PWD in PASSWORD
screen before entering control group (G.CTL) of parameter group.
Not allow for entering parameter group if input value is not the same as
registered password. Its initial setting U.PWD is ‘0’.
The parameter to initialize the controller. It is initialing when ‘INIT’ sets ‘ON’
(However, not allow communication for initializing)
- Be sure not to forget PASSWORD after registration.
- If Forget the PASSWORD, Not available for operator’s maintenance.
Need to return the controller for our service center and sales office.
It will be initialized all parameters of the controller when ‘INIT’ parameter sets.
Be sure to avoid any kind of inconvenience.
The parameter to set operation status of the controller in effect of external
contact input when it sets option(/DI). The Controller operation of DI.SL
setting is refer to ‘Table of DI Operation’ as shown on belows.
The parameter to set ON/OFF Mode. Control Output is OUT1(RLY) When set
ON/OFF Mode.

If HYS is 1.0 ON Range is HYS/2, OFF Range is HYS/2.
Sym Parameter Setting Range Unit Initial Remark
US1
US2
LOCK
DI.SL
OSTS
DSP.H
DSP.L
INIT
User Screen OFF, D-Register Nomber(1∼1299) ABS OFF All time
indicate
User Screen OFF, D-Register Nomber(1∼1299) ABS OFF All time
indicate
Key Lock OFF, ON (No Editing) ABS OFF All time
indicate
DI Selection OFF, 1, 2 ABS OFF DI Option
OUTPUT STATUS OFF, ON ABS OFF All time
indicate
Display High Limit EU(-5.0∼105.0%)
: However, DSP.L<DSP.H EU EU(105.0%) All time
indicate
Display Low Limit EU(-5.0∼105.0%)
: However, DSP.L<DSP.H EU EU(-5.0%) All time
indicate
Parameter
Initialization OFF, ON ABS OFF All time indicate
S-TM Start Time OFF(0.00)∼99.59(min) TIME OFF All time
indicate
U.PWD User Password 0∼9999 ABS 0All time
indicate
P-TM Process Time OFF(0.00)∼99.59(min) TIME OFF All time
indicate
A/M AUTO, MAN AUTO, MAN ABS AUTO All time
indicate
ONOF ON/OFF Mode ON, OFF ABS OFF Except
H/C TYPE
HYS/2
HYS/2
ON
OFF
ON
PV
SP
OUT1
RLY

5.4 SP Group(G.SP)
Press ‘SET/ENT Key to select SP Group after press ▼ or ▲ Key in Menu
display.
G.AT ↔ ↔ G.PID ↔ PWD ↔ G.CTL ↔ G.IN
↑ ↕
G.COM ↔ G.RET ↔ G.ALM ↔ G.OUT
▲▼ ▲▼ ▲▼
▲▼
▼
▲▼
▲▼
▲▼
▲▼
▲▼
The parameter to set Running mode for ‘RUN’ or ‘STOP’.
The parameter to set the type of SP to be running in the controller.
It can be selected one among ‘RSP, SP1, SP2, SP3, SP4’.
Its initial setting is ‘SP1’
(※ When communication option(/RS), it runs for SYNC-SLAVE.
If MASTER, RUN/STOP, SP for initializing, must set SPSL = RSP)
The parameter to set SP Value for Running.
The SP Value can be able to setting up Max 4 Ea, and One SP value will be
selected by SPSL parameter.
The parameter to set High-Limited value when input setting value.
the ‘SPrH’ can initialize when sensor input set or ‘In.rH’ (In.SH When mV, V
Sensor input) when changing of ‘In.rH’
The parameter to set Low-Limited value when input setting value.
the ‘SPrL’ can initialize when sensor input set or ‘In.rL’ (In.SL When mV, V
Sensor input) when changing of ‘In.rL’
The parameter to set time unit as HH.MM (hour.minute) or
MM.SS(minute.second) for time relating parameters. Its initial setting is
HH.MM. ※’S-TM’ and ‘P-TM’ works without any effect from TMU parameter.
The parameter to setting for SP ascending or descending gradually in Time-
propositional to changed SP value when SP changed.
The U.SLP /D.SLP can set SP ascending or descending rate per sec or min
referring to Time unit of TMU parameter. When U.SLP/ D.SLP set value is
‘OFF’, input SP value is working to controller not effected by SP changing rate
when SP changed. Initial setting of ‘U.SLP/D.SLP is ‘Off’
.
.
.