Samwontech TEMI770 User manual

Color Programmable
Temperature & Humidity
Controller
T E M I 7 7 0
TEMI570
T E M I 5 5 0 N
Manual

CONTENTS
IM TEMI550E_C 2nd Edition: Sep. 1. 2003. 1/3
CONTENTS( I : INSTALLATION )
1. Introduction and Power Unit
1-1. Introduction
- Introductions on user’s guide
- Protection, safety and prohibition
-LimitedWARRANTY
-Warrantypolicy
- Symbols marked in this manual
1-2. Power Unit
2. Package and accessory check list
2-1. - Model number and suffix codes
2-2. - Components
2-3. - Missing or damaged items
3. Installation
3-1. - Location
3-2. - Caution
3-3. - External and panel cutout dimensions
3-4. - Panel cutting
3-5. - Installation (Mount)
3-6. - Installation (Wiring ground)
4. Wiring
4-1. - How to connect wires
4-1-1. Applicable power source cable
4-1-2. Applicable tightening torque
4-1-3. Noise rejection
4-2. - Terminal wiring diagram
4-2-1. Grounding
4-2-2. Analog input
4-2-3. Analog output
4-2-4. Relay: External contact output
4-2-5. External contact input: DI
4-2-6. Relay
4-2-7. Communication (RS485/RS232)
I - 1
I - 1
I - 1
I - 1
I - 2
I - 2
I - 2
I - 2
I - 3
I - 3
I - 3
I - 3
I - 4
I - 4
I - 4
I - 5
I - 5
I - 6
I - 6
I - 7
I - 7
I - 7
I - 7
I - 7
I - 8
I - 8
I - 9
I - 10
I - 11
I - 12
I - 13
I - 14

CONTENTS
IM TEMI550E_C 2nd Edition: Sep. 1. 2003. 2/3
CONTENTS ( II : User's Guide )
1. Setup button
1-1. Initial setup button
1-2. Input setpoint
1-3. Input error
2. Input setpoint
2-1. Function of setpoint key
2-2. Parameter
3. Block of basic processing
4. Operation & Setup
4-1. Program stop
4-2. Program run
4-3. Fixstop
4-4. Fixrun
5. Main
5-1. Function
5-2. Reserve
5-3. Graph
5-4. Program
5-4-1. Pattern
5-4-2. Repeat
5-4-3. File edit
5-4-4. TS(Time signal)
5-4-5. Wait
5-4-6. Test name
5-5. LCD Light
5-6. Setup
5-6-1. Input
5-6-2. OUTPUT
5-6-3. IS(Inner signal)
5-6-4. PID Setting
5-6-4-1. Temp PID
5-6-4-2. HUMI PID
5-6-4-3. PID Group(PID1 ~9)
5-6-5. Do Config
5-6-6. Alarm
5-6-7. Comm
5-6-8. Display(Password/Language/Company Info)
5-7. Setup Password
6. Trouble
II - 1
II - 1
II - 1
II - 1
II - 2
II - 2
II - 2
II - 3
II - 4
II - 4
II - 5
II - 6
II - 6
II - 7
II - 7
II - 9
II - 10
II - 11
II - 12
II - 15
II - 17
II - 18
II - 20
II - 21
II - 21
II - 22
II - 23
II - 26
II - 27
II - 27
II - 29
II - 30
II - 31
II - 33
II - 34
II - 35
II - 35
II – 35
II - 36

CONTENTS
IM TEMI550E_C 2nd Edition: Sep. 1. 2003. 3/3
CONTENTS ( III : COMMUNICATION )
1. Communication
2. Communication terminal arrangement
2-1. Terminal RS232C & TEMI550 9 Pin connector
2-2. Terminal RS485 & TEMI550'S terminal
3. Communication command
3-1. Communication command contents
3-2. Communication commands
3-3. Error response
3-4. RSD Command
3-5. RRD Command
3-6. WSD Command
3-7. WRD Command
3-8. STD Command
3-9. CLD Command
4. D-REGISTER
4-1. Process
4-2. Functions
4-3. Reservation
4-4. IS & Alarm
5. Set program pattern
5-1. Program
5-2. Reading program pattern
5-3. Writing program pattern
5-4. Pattern copy/delete & segment insert/delete
5-5. PTTN_INFO
D-REGISTER DETAIL
III - 1
III - 2
III - 2
III - 2
III - 3
III - 3
III - 4
III - 4
III - 5
III - 6
III - 7
III - 8
III - 9
III - 10
III - 11
III - 12
III - 14
III - 15
III - 16
III - 17
III - 17
III - 18
III - 18
III - 19
III - 20

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 1/15
1. Introductions and Power Unit
Thank you for purchasing our Industrial Controller.
This manual explains suitable effective way of using and installing this product.
Please read carefully to apply it to controller of environmental chamber or others.
1-1. Introduction
Regarding This Document
(1) Keep the manual for the last user who can get easy access to the manual.
(2) Make sure read this manual carefully and fully understand how to operate this product.
(3) This manual is intended to describe the functions of this product.
Samwontech Co., Ltd.(hereinafter simply referred to as We) does not guarantee the application
of these functions for any particular purpose.
(4) Redistribution & use this manual, with or without modification, are prohibited.
(5) The contents of this manual are subject to change without prior notice.
(6) Every effort has been made to ensure accuracy in the preparation of this manual. However,
should any errors be found or important information be omitted, please contact your nearest our
representative or our sales office.
Regarding Protection, Safety and Prohibition
(1) In the interest of protecting and ensuring the safety of this product and the system, which is
controlled by this product, ensure that all instructions and precautions and precautions in this
manual relating to safety are strictly adhered to in the use of this product.
(2) Take note that if you handle the product in contradiction to these instructions, we does not
guarantee safety.
(3) If separate protection and/or safety circuits are to be installed for this product or the system, which
is controlled by this product, ensure that such circuits are installed external to the product.
(4) When you replace parts or consumables of the product, use those specified by us.
Limited WARRANTY
(1) We makes no warranties regarding the product except those mentioned in the WARRANTY.
(2) In cases where the use of this product results in damage or loss to the user or a third party, we will
not be responsible for any incidental or consequential damage or loss, or any damage or loss
suffered by the user or third party resulting from a defect or defects in this product which could not
be foreseen by us.

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 2/15
Warranty Policy
(1) Warranty term is 1year parts and labor. We make warranties
regarding the product only those mentioned in the WARRANTY.
(2) A/S is needed actual expenses, after warranty period.
(3) Regarding Force Majeure
This warranty does not cover damage due to loss password, accident,
fire, flood and/or other acts of God; misuse, instability, improper
installation, improper or unauthorized repairs, commercial adjustments
which are explained in the instruction manual are not covered under the
termsofthiswarranty.Thiswarrantywillautomaticallybevoided
for any unit found with a missing or altered serial number.
(4) All warranty repairs must be performed by a our authorized service center.
Symbols Used in This Manual
The symbols used in this user manual have the following meanings:
(1) or
These symbols are used for danger or warning.
(1) Product : Indicates an imminently hazardous situation which,
ifnotavoidedwillresultinseriousinjuryoroutoforder.
(2) User manual : Indicates an imminently hazardous situation which,
ifnotavoided,willresultinseriousinjuryordeath.
(2)
Ground
This symbol indicates that the terminal must be connected to ground prior
to operation of equipment.
(3) or
Draws attention to information essential for understanding the operation and features.
(4) ☞
Seealso
Gives the reference locations for further information on the topic.
1-2. Power Unit
Power supply voltage rating ; 100-240VAC, Max 0.1A, 50/60Hz
Power consumption : Max 18W, Max 22VA.
Mains supply voltage fluctuations : 100-240VAC(±10%)

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 3/15
2. Package checklist
Check the following when removing the controller from its package. Check the contents of the
package against the Package List to make sure that all accessories are included in the package.
2-1. Model and suffix codes
Check the controller for any apparent physical damage.
Check point : Model number which is located right side of box and left side of controller.
MODEL OPTION DESCRIPTIONS
1 Standard I/O Board(10Points)
2 Additional I/O Board(10Points)
0 RS232C
TEMI 770 –
TEMI 570 –
TEMI 550N –
1 RS485
☞(Ex) Standard is TEMI 770-10(Standard I/O Board + RS232C)
2-2.Components
Check that the following items are provided.
2-3. Missing or damaged items
If any of these items are missing or damaged, please contact your agent
or sales representative for assistance.
2-4. Life time of the parts in the controller
Check the life time for parts and we strongly recommend replace it if the life time finish.
■FUSE (ST5100UK) SR-5:630mA/250VAC : Semi-permanent.
■BACKLIGHT (ST5100TL) : 10,000 ~ 15,000 HOUR
■RELAY (ST3300PJ) JW2SN-DC24V : Around ON/OFF 300,000 times
■BATTERY (ST5100RX) SBAA02(3.6V) 1/2AA : Around 200,000 Hours
☞Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type.(SBAA02) Dispose of used battery separately from other waste.
MODEL CODE DESCRIPTIONS
Controller 1 TEMI 770-10, -11, -20 or 21
Brackets 2 ST5300AF (Mount Assy)
Manual 1 This book

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 4/15
3. Installation
3-1. Location
IMPORTANT
NEVER touch the terminals or else you will get an electrical shock, if the unit is power-on.
To install the controller, select a location where:
■No one may accidentally touch the terminals,
■Mechanical vibrations are minimal,
■Corrosive gas is minimal,
■Temperature can be maintained between 10℃to 50℃and fluctuation is minimal,
■Indoor use only,
■Altitude is up to 2,000m
■No direct radiant heat or ultraviolet rays is present,
■No magnetic disturbances are caused,
■No wind blows against the terminal board(reference junction compensation element),
■No dust or salt content,
■No flammable materials are around,
Although, the case of this system and the bezel are made of fire retardant SPCC-SD&ABS/PC
respectively, do not install the system near inflammable materials. Also, avoid placing the system
on inflammable materials directly.
3-2.Caution
CAUTION
■There in little influence fro electromagnetic fields and noise
■No moisture can get into the system.
■Ambient temperature and humidity : 10~50℃, 20~90%RH. (At non-freezing status)
■Storage temperature and humidity : -25~70℃, 5~95%RH. (At non-freezing status)
■If you want to use it after keeping it under 0°C, you need to warm it up for 2 hours at
room temperature before plugging it in and warm it up for 30minute after plugging it in.
Otherwise, it may not function normally and the product may be damaged.
■Do not use around any machine, which heat up.
■Avoid installing it with the front facing slant.
■Transient over voltage category is category II.
■Applicable rated pollution degree is pollution degree II.
■Before starting wiring, be sure to turn off the system or else you will get an electrical shock.
■Install the guard panel under the controller for your safety and installation with easy.
■The I/O relay board must be installed inside of Temperature & Humidity Chamber.
■The I/O relay board must be tied up with 4piese of bolt and nut at the 4hole on the I/O
relay board.

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 5/15
3-3. External and Panel Cutout Dimensions
3-4. Panel cutting
180.80 (7.12) 14.32 (0.56) 93.4 (3.71)
133.90 (5.27)
Panel Thickness : 1 (0.04)~10(0.39)
Unit: mm, ( ): Inch
Unit: mm, ( ): Inch
+0.8
(
5.30
)
134.5
+0.8
(6.85)
174
65.2 (2.58)
76
(
2.99
)
Min 250
(
9.84
)
Min 200 (7.87)
0
0
+0.8
(
5.30
)
134.5 0
+0.8
(6.85)
174 0

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 6/15
3-5. Installation (Mount)
1) Cut the mounting panel as Section 3-4. PANEL CUTTING.
2) Insert the unit from its back terminal board side.
3) Attach the left and right brackets to the unit to fix the unit to the mounting panel. (Use screwdriver)
CAUTION (Mount)
Do not tighten the mounting screw excessively, or the unit case
or bracket may be damage.
3-6. Installation (Wiring for ground)
CAUTION (Wiring for ground)
1. Make sure ground with temp. & humi chamber case when install power injection.
2. Make sure wiring of ground power source with circuit breaker in the temp. & humi. chamber.
3. Make sure wiring of ground with controller circuit breaker in temp. & humi. chamber.
Screwdriver
Unit: mm, ( ): Inch
Panel
Insert
Mount
Panel Thickness: 1(0.04)~10(0.39)
SUPPLY INPUT1 INPUT2
RS232
100 - 240VAC CAUTION
★
★
★★
L 1
N 1
G 1
N 2
G 2
L 2
Contact Input
SSR/SCR, Recorder
(Transmission output)
DI
Relay Contact Output
I/O Board
L1 L2
N1 N2
G1 G3
Circuit Breaker
Chamber
Case

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 7/15
4. Wiring
CAUTION
■Before carrying out wiring, turn off the power to the controller and check that the cables to be
connected are not alive with a tester or the like because there is a possibility of electric shock.
Personnel who have basic electrical knowledge and practical experience must carry out wiring.
■The controller must be wired directly from circuit breaker output on inside of temperature &
humidity Chamber for avoid damage of controller or temperature & humidity Chamber.
4-1. How to connect wires
4-1-1. Applicable power source cable : Vinyl insulation cable KSC 3304 0.9~2.0 ㎟
4-1-2. Applicable tightening torques
Please use-tightening torque with insulating sleeve for M3.5 screws as shown in the following Figure:
4-1-3. Noise rejections
■Reason making noise
(1) Relay and relay contact point (2) Solenoid coil, solenoid valve
(3) Power source line (4) Inductive load
(5)Invertors (6)Commentatorsofmotor
(7)Phase-angleSCR (8)Wirelesscommunication
(9)Welder (10)High-tensionigniter,etc.
■Solutions
When wiring, comply with the following to protect the controller from noise sources:
(1) Keep away the cables to the input circuit from the power supply
circuit or the grounding circuit as much as possible.
(2) Using a shielded cable is effective in avoiding noise from electrostatic induction. Connect a
shielded cable to the grounding terminal as required. Avoid two-point grounding.
(3) To avoid noise from electromagnetic induction, it is relatively
effective to mutually twist the input cables at regular short intervals.
5.8mm or less
5.8mm or less
Φ3.0mm or more
Φ3.0mm or more

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 8/15
4-2. Terminal wiring diagram
Figure 4-2-B TEMI 770-11 Type
Figure 4-2-C TEMI 770-20 Type
Figure 4-2-D TEMI550-21 Type
Figure 4-2-A TEMI 770-10 Type
Figure 4-2-E Standard I/O board and Additional I/O board
CAUTION
★(8Ea) are not for connection terminals, these are only for install.
Avoid used those place, it might make damage to system or out of order.
CAUTION
Before carrying out wiring, turn off the power to the controller and check
that the cables to be connected are not alive with a tester or the like because
there is a possibility of electric shock. Wiring must be carried out by personnel
who have basic electrical knowledge and practical experience.
※This shapes are depends on model.
RS232 I/O 2 LINK
SG
RTX+ RTX-
RXD TXD
RS485
SG
RTX+ RTX-
RXD TXD
RS485 I/O 2 LINK
RLY10_NC RLY10_NO COM3 RLY9_NO RLY9_NC
RLY8
_
NC RLY8
_
NO COM2 RLY7
_
NO RLY7
_
NC
COM1 RLY6 RLY5 RLY4 RLY3 RLY2 RLY1
P7
GND
P3
AOUT1+ AOUT1- AOUT2+ AOUT2-
(TEMP) (HUMI)
RET1+ RET1- RET2+ RET2-
DI_1 DI_2 DI_3 DI_4 DI_5 DI_6 DI_7 DI_8 DI_COM
Additional board does not have those parts.
*External Contact Switch
It is working
together as
“AND” condition
with RELAY 10.
100-240VAC
SUPPLY INPUT1 INPUT2
I/O1 LINK
RS232
100~240VAC CAUTION
★
★
★★

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 9/15
4-2-1. Grounding
■Use a cable 2 ㎟or more thick for grounding with class 3 grounding(grounding
resistance a 100Ωor less) or higher. Do not extend the grounding cable over 20m.
■Ground from the ground terminal with a one-point contact.
Do not wire between ground terminals.
■Use appropriate cables equivalent to vinyl insulation cable(KSC 3304) or more.
4-2-2. Analog input
CAUTION
Before starting analog input wiring, be sure to turn off the system or else you
willgetanelectricalshock.
IMPORTANT
■When connection, do not mix up the input polarity. Connecting with the wrong
polarity can cause the unit to malfunction.
■For input wiring, use a shielded cable. Ground the shield at one point.
and grounding circuits as possible.
(1) Resistance Temperature Detector (RTD) INPUT
(2) DC VOLTAGE INPUT (3) DC CURRENT INPUT
B
b
A
SHIELD
RTD
INPUT 2INPUT 1
RTD
B
SHIELD
A
b
SHIELD
DCV _
+
mA R
SHIELD
+
_
V : 1 ~ 5 V R = 2 5 0 Ω: 1 ~ 5 V
FG
100~240V AC
50/60 Hz
Ground FRAME GROUND (FG) EXACTLY.
Class 3 Ground
Class 3 Ground Class 3 Ground
100-240VAC
0.1A, 50/60Hz
Class 3 Ground Class 3 Ground

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 10/15
4-2-3. Analog output
CAUTION
Before starting analog output wiring, be sure to turn off the system or else
you will get an electrical shock.
IMPORTANT
■When connection, do not mix up the input polarity, Connecting with the
wrong polarity can cause serious accidents.
■For input wiring, use a shielded cable. Ground the shield at one point.
(1)SSR/SCR
CAUTION
Before starting ACTUATOR install/uninstall wiring, be sure to turn off
the system or else you will get an electrical shock.
■Wiring for temp output(4~20mA/SSR) ■Wiring for humi output(4~20mA/SSR)
(2) Wiring for transmission output
CAUTION
Before starting receiver( or recorder, etc) install/uninstall wiring,
be sure to turn off the system or else you will get an electrical shock.
■Wiring temp transmission output(4~20mA) ■Wiring humi transmission output(4~20mA)
4~20mA DC
SHIELD
_
+
4~20mA DC
RET2+
RET2 -
+
_
SHIELD
RET1 -
RET1+
조작단
VALVE
CONTROL
SHIELD
_
+
AOUT1 -
AOUT1+
SHIELD
CONTROL
VALVE
+
_
AOUT2+
AOUT2 -
Class 3 Ground Class 3 Ground
I/O 1I/O 1
Class 3 Ground Class 3 Ground
I/O 1 I/O 1
CONTROL
VALVE CONTROL
VALVE

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 11/15
4-2-4. Relay : External contact output
Caution
Before carrying out wiring, turn off the power to the controller and check that the cables to
be connected are not alive with a test because there is a possibility of electric shock.
30VDC 5A Less, 250VAC 5A Less
COM 1
RLY 6
RLY 5
RLY 4
RLY 3
RLY 2
RLY 1
I / O 1
30VDC 5A Less, 250VAC 5A Less
RLY8_NC
RLY8_NO
COM 2
RLY7_N0
RLY7_NC
RLY9_N0
RLY10_NC
RLY10_NO
COM 3
RLY9_NC
I / O 1 I / O 1

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 12/15
4-2-5. External contact input: DI
CAUTION
Before starting external contact output:DI wiring, be sure to turn off
the system or else you will get an electrical shock.
■For the external contact, use a no-voltage contact(including relay contact)
that can operate appropriately under the terminal voltage for a close
contact(approximate.. 5V) and the current for a opened contact(approximate.. 1mA).
■When using an open collector, select one with the 2V or less voltage for
the closed contact, and 100µA or less leakage current for the open contact.
DI_COM
+5 V
DI_8
DI_7
DI_6
DI_5
DI_4
DI_3
DI_1
DI_2
DI_5
DI_COM
DI_8
DI_7
DI_6
DI_4
DI_3
DI_2
DI_1
Current when ON : approxi. 1mA
▲RELAY contact input
▲TRANSISTOR contact input

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 13/15
4-2-6. Auxiliary Relay
CAUTION
If contact capacity is over 250VAC - resistance load 5A, 30VDC - resistance load 5A,
useauxiliaryrelayforON/OFFload.
■If you INDUCTANCE(L) load like as AUXILIARY RELAY or SOLENOIDE VALVE,
it might make go to wrong or out of order relay, please make sure insert to parallel circuit
with CR FILTER(AC) or DIODE(DC) by SURGE SUPPRESSOR of avoiding sparks.
■Recommend CR FILTER
▶Sung Ho Electronics : BSE104R120 25V (0.1μ+120Ω)
▶HANA PARTS CO. : HN2EAC
▶Songmi Electric Co., Ltd : CR UNIT 953, 955 etc
▶Jiwol Electric Co., Ltd. : SKV, SKVB etc
▶Shinyoung Communication Co., Ltd. : CR-CFS, CR-U etc
(A) DC RELAY
(B) AC RELAY
R
RELAY
Out DC power
Machine
Use what a rated Relay Coil is must
be less than contact point capacity.
Connect Relay Coil socket directly
DIODE
R
RELAY
Out DC power
RC Filter
Use what a rated Relay Coil is must
be less than contact point capacity.
Connect Relay Coil socket directly

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 14/15
4-2-7. Communication(RS485/RS232)
CAUTION
Before starting communication wiring, be sure to turn off the system or
else you will get an electrical shock.
(1) RS485(Optional specification)
■The slave side(TEMI 770) can accommodate up to 31 units in a MULTIDROP connection.
■Be sure to connect a terminating resistance(220Ω1/4W) to the units at the both
(2) RS232C(Standard)
■CONNECTOR : Wiring with 9 PIN
SG
RTS
CTS
5
SHIELD
8
7
(
D-Sub 9 Pin
)
RD
TD 3
2
TxD
RxD
SG
(D-Sub 9 Pin Female)
3
2
5
SG
SHIELD
RTX+
RTX-
SG SG
RTX-
RTX+
RTX+
RTX- Termination
Resistance
Termination
Resistance
Class 3 Ground
Class 3 Ground
Controller Controller
Class 3 Ground
Master Station

I. INSTALLATION
IMTEMI770E_C2ndEdition:Sep.1.2003. 15/15
Blank
If you find any mistaken or wrong information in this manual
PLEASE mail to [e-mail]
www.samwontech.com

II.USERS
IM TEMI 770E_C 2nd Edition: Sep. 1. 2003. 1/40
1. Setup button
TEMI 770 is easy to install & modify by touch screen as well as the map type menu. Enable to grasp the operation
of control system with easy through graph on vivid LCD screen.
1-1. Initial setup button
(Table 1-1)
Button Function
1 MAIN Change the page.
2 ON / OFF On / Off & Selection
3 SETPOINT Switch to the page for input a Setpoint value data
1-2. Input Setpoint
1. Select Setpoint button.
2. It is showing the Figure 1-1 for input a data.
3. If user input data which is invalid, it makes 3 times buzzer, also there is -LIMIT ERR message
on the Setpoint display.
Parameter
Range Setpoint display
Figure 1-1
Key Lock
1.KEYLOCK-ON -> Lock
2.KEYLOCK-OFF -> Unlock
☞For more information, see 5.1 FUNCTION
1-3. Input error
User can check a number of buzzer times.
1) 1 time : Succeed set the data
2) 3 times : Failed set the data
Using the touch screen
Please do not use any pen/pencil, nail or any other sharp material.
Otherwise, the touch screen might be broken or out of order.
MAIN
ON OFF
0.0