San Telequip SC09FED H User manual

San Telequip (P) Ltd.,
504 & 505 Deron Heights, Baner Road,
Pune 411045, India
Phone : [phone] Connecting Converting Leading!
email : [e-mail] .
User Manual for 10/100 Base TX to 100 Base FX Media Converter, Model SC09FED H
The 10/100M Fiber Ethernet Media Converter series is designed to meet the massive needs for
network deployment and able to extend a copper based Fast network via fiber cable to a maximum
distance up to 120KM
SC09FED H Media Converter is fully compliant with IEEE802.3, IEEE802.3U, 10/100Base-TX,
100Base-FX, standards. The installation & operation procedures are simple & straightforward.
Operation status can be locally monitored through a set of Diagnostic LED’s.
Technical Specifications
Standards
IEEE802.3,10 Base-T standard, IEEE802.3U, 100Base-TX/FX standard
Connector
One RJ-45connector & one SC/ST connector
Operation mode
Full duplex mode or Half duplex mode
Fiber Cable
Multi-Mode : 50/125,62.5/125 or 100/140um
Single mode: 8.3/125,8.7/125,9/125 or 10/125um
Ethernet cable
Cat 5 UTP cable
Power Supply
230V AC External Adapter
Operation Temperature
0 ℃to 60 ℃
Relative Humidity
5% to 90% rh Non-condensation.
Dimensions
26mm x 70mm x 95mm
Connection & LED Indicator
Ethernet /RJ-45 interface: The transmission media is CAT5 twisted-pair with typical length of 100
meter supporting MDI/MDI-X
Fiber interface: SC/ST fiber interface is of duplex mode type with two interfaces, namely TX and RX.
When the two sets of optical transceiver are interfaced to a switch with fiber interface, the fiber is in
cross connection, namely "TX-RX", "RX-TX"
Basic Network Connection
Fig.1 Basic Network Connection
Fig.2 Front Panel

San Telequip (P) Ltd.,
504 & 505 Deron Heights, Baner Road,
Pune 411045, India
Phone : [phone] Connecting Converting Leading!
email : [e-mail] .
LED Functions
The following is the explanation for each LED
LED indicator lamp
Status
Explanation
FX Link/Act
On
Connection status display for fiber link
“ON” indicates that Fiber link is correct
Blink
Active status displays of fiber link
“Blink” indicates packet is going through Fx end
TX Link/Act
On
Connection status display for Ethernet link
“ON” indicates that Ethernet link is in correct
Blink
Active status displays of fiber link
“Blink” indicates packet is going through Tx end
FDX/COL
On
Transceiver works in the Full duplex mode
Off
Transceiver works in the Half duplex mode
PWR
On
Power is ON and Normal.
SD
On
Fiber signal is detected
100M
On
Transfer rate of Ethernet Port is 100Mbps
Off
Transfer rate of Ethernet Port is 10Mbps
DIP Switch Selection
Note: before using LFP function, please re-power
on the both converter after connecting all the
copper cables and fiber patch-cords.
Fig 3. DIP switch selection
Troubleshooting
Is the power LED on the media converter ON?
Is the Power adapter of proper type (voltage and frequency) for the AC socket?
Is the power adapter properly installed in the media converter and in the socket?
Is the “Link/ACT” LED ON on the port with twisted-pair cable inserted?
Check for proper connection for Ethernet cable
Green = the media converter has selected full-duplex mode
OFF = the media converter has selected half-duplex mode
If the mode is not correct, disconnect and reconnect the twisted pair cable
Is the “LACT” LED glowing on the fiber cable port?
Check the fiber cables for proper connection
Verify that the TX and RX cables are connected to the RX and TX ports, respectively, on the
100Base-FX device.
Is the “Speed” LED glowing on a port with twisted-pair cable installed?
Check the copper cables for proper connection
Green = the media converter has selected 100Mb/s operation
OFF = the media converter has selected 10Mb/s operation
If the speed is not correct, disconnect and reconnect the twisted pair cable
If the problem still persists, pls contact us @ [e-mail] / [phone]