Sangamo Choice RSTAT5 RF User manual

Choice RSTAT5 RF
Wireless Digital Programmable Thermostat
User Instructions
A programmable thermostat differs from a programmer that you may be used to.
With this thermostat you do not set on and off times. Instead you are setting your
desired temperature at varying points throughout the day. This means your home
will always be comfortably warm when needed but you will not be wasting energy
(and money) heating your home when it’s not required.
If your thermostat is set to 21°C, for example, your boiler will run until the
thermostat reads over that temperature and then tell the boiler to turn off,
meaning you won’t be calling for heat when your home is already at your desired
temperature.
When you set a temperature you are saying you don’t want the heating to come on
unless the room temperature is lower than the set temperature.
WHAT IS A PROGRAMMABLE THERMOSTAT?
The Choice RSTAT5 RF comprises of a portable battery powered thermostat
(transmitter) and a separate wall mounted mains relay box (receiver). The
transmitter should be located in the main living area and the receiver is mounted
close to the boiler.
This programmable room thermostat has been designed to bring you comfort and
energy economy. It allows you to program and regulate your heating system using
up to 6 programmable events per day.
To ensure its correct operation the thermostat should be mounted or situated
approximately 1.3m above the oor and away from direct sunlight, heat sources and
drafts.
INTRODUCTION

What is switching dierenal?
Without a switching dierenal your boiler would
stop the instant it reached the desired temperature
then start to fall where it would instantly kick back in
again and be stuck switching your boiler on and o
repeatedly. A switching dierenal creates a band
around the temperature to allow the set temperature
to be maintained. We recommend using 0.5°C unless
you have a specic reason not to.
▲Increase or
▼Decrease
Ok and Set
Program/Internal settings
MOverride functions
Set Temp
+0.5°C
+1.0°C
-0.5°C
-1.0°C
Boiler
ON Boiler ON Boiler ON
Boiler
OFF Boiler OFF Boiler OFF
SETTING THE TIME AND DATE
Before you set the thermostat you should x the me and date.
1. Press and hold Set for 6 seconds.
2. Choose between °F and °C using ▼▲ and press Ok.
3. Choose between 24hr and 12hr clock using ▼▲ and press Ok.
4. Set the Year using ▼▲ and press Ok.
5. Set the Month using ▼▲ and press Ok.
6. Set the Day using ▼▲ and press Ok.
7. Set the Hour using ▼▲ and press Ok.
8. Set the Minute using ▼▲ and press Ok.
9. Choose between 0.5°C and 1.0°C switching differential using ▼▲ and press Ok.
10. 4 dashes appear on the display, this can be used to set a reminder to replace filters
in an air conditioning system, press Ok to skip this.
11. Press Ok to return to Run Mode
0.5°C Switching
Dierenal
?

Mo - Fr Time °C
1: MORN 6:00am 21°C
2: DAY 8:30am 15.5°C
3: Noon 12:00pm 21°C
4: Break 2:00pm 15.5°C
5: EVEN 4:30pm 21°C
6: NIGHT 10:30pm 18.5°C
Sa - Su Time °C
1: MORN 7:00am 21°C
2: DAY 8:30am 21°C
3: Noon 12:00pm 21°C
4: Break 2:00pm 21°C
5: EVEN 4:30pm 21°C
6: NIGHT 10:30pm 18.5°C
DEFAULT PROGRAM
The Choice RSTAT5 RF comes preset with a default program so that you can get up
and running straight away. Each day is split into 6 parts each one can have it’s me or
temperature changed to suit you.
CUSTOM PROGRAM
Most users will want to alter these mes to suit their own circumstances. A good starng
point is to think about the parts like so:
MORN: When does the first person in your home get up?
DAY: When does the last person leave in the morning?
Noon: If anyone is home at lunchtime, when?
Break: and when do they leave again?
EVEN: What time does the first person get back home in the afternoon/evening?
NIGHT: What time is everyone in your home in bed?
and when thinking about temperatures:
When people are home: Set depending on your minimum desired comfortable
temperature. (see below for more details)
When no-one is home: Set depending on how quickly your home heats up.
At night: The heang should be lowered, cooler temperatures help you sleep.
What temperature should I heat my home to?
Turning your room temperature down just one degree can have signicant
savings on your energy bill. A good way to get the right temperature for you is
to start at 21°C, leave it for a week and lower 1°C. Repeat this process unl you
noce it being a lile too cool and turn it back up 1°C. You now have the lowest
possible comfortable seng.
?

MORN DAY Noon Break EVEN NIGHTNIGHT
CUSTOM PROGRAM cont...
Below shows the programming segments of the default program on a Weekday.
Held over from previous
day’s setting.
Essenally, if the thermostat reads the temperature below the chosen temperature it will
send a message for the boiler to re and your heang to come on.
The above diagram shows how the day is split up into named parts but BOTH the mes
and temperatures are changeable. Using the programming instrucons that follow you
can set the me each part starts and the temperature it will set to at that point. As can be
seen the NIGHT seng carries over & stays unl the MORN me the following day.
If you don’t need a certain program to be there, for example you do not require Noon as
no one is home at that me of the day, then you simply set that program for the same
temperature as the one before - as it cannot be deleted. There must be 6 programmed
events each day even if they are set to the same temperature.
Mo - Fr Time °C
1: MORN
2: DAY
3: Noon
4: Break
5: EVEN
6: NIGHT
Sa - Su Time °C
1: MORN
2: DAY
3: Noon
4: Break
5: EVEN
6: NIGHT
CREATING YOUR PROGRAM
Use the grids below to plan out your own custom program before you start.
2am 6am 10am 2pm 6pm 10pm
6:00am 8:30am 12:00pm 2:00pm 4:30pm 10:30pm

COPY/PASTE DAY
To speed up the programming sequence you can copy
one day into another, or several other, days.
1. Press Set x2 to enter copy mode.
2. Choose the ‘Copy’ day using ▲ and press Ok.
3. Choose the ‘Paste’ day using ▲ and press Ok.
4. Repeat step as required for further ‘Paste’ days
At any point Press Ok x2 to return to Run Mode
RESET UNIT
To erase all current sengs and return to it’s factory
default sengs & programs.
1. Press and hold Ok and ▼ for 6 seconds.
2. When Reset is displayed push in the Reset buon.
3. All segments on the display are shown to conrm
reset has taken place.
PROGRAMMING
Within programming mode the thermostat will return
to normal operaon if no buons are pressed for 30
seconds.
To exit programming mode either wait 30 seconds or
press Set x2 and Ok.
NB: Each day’s end me is 11:59 in 12hr or 23:59 in 24hr
formats. P6 should never be set for midnight as this will
cause an error in programming.
Each day of the week can be programmed separately,
starng with Monday (Mo)
1. Press Set to enter programming mode.
2. Set Mo MORN temperature using ▼▲ and press Ok.
3. Set Mo MORN me using ▼▲ and press Ok.
4. Set Mo DAY temperature using ▼▲ and press Ok.
5. Set Mo DAY me using ▼▲ and press Ok.
6. Repeat procedure for all 6 set points in the day and
connue on to program each day of the week.
At any point Press Set x2 then Ok to return to Run Mode
Prog is shown at the
top of the display
Copy Prog is shown at
the top of the display

CHANGE THE TEMPERATURE FOR A SET NUMBER OF HOURS
You can also set the thermostat to hold at the temperature you want for a dened
number of hours.
1. Press M to enter override mode then select temperature using ▼▲ and press Ok.
2. Select number of hours using ▼▲ and press Ok.
3. Comfort Override, Temp. Set & Hours, with the hours remaining, are shown on the
display.
To cancel seng and return to normal operaon press Ok.
CHANGE THE TEMPERATURE
To manually change the temperature temporarily you simply press the raise or lower
buons to the desired level, if le alone this will stay set unl the next programmed
change at which point it returns back to the original schedule.
1. Choose desired temperature using ▼▲
To cancel seng early and return to normal operaon press Ok.
Temporary Override
is shown above the
me on the display
Comfort Override
is shown above the
me on the display.
Time changes to
countdown of the
remaining hours and
minutes.

HOLD TEMPERATURE PERMANENTLY
Hold the thermostat at a desired temperature unl manually cancelled by you.
1. Press M x2 to enter permanent override mode then select temperature using ▼▲
and press Ok.
2. Permanent Hold and Temp. Set are displayed.
To cancel seng and return to normal operaon press Ok.
HOLIDAY MODE
Hold the temperature at a desired set point unl a specic date.
1. Press M x3 to enter holiday mode then select temperature using ▼▲ and press Ok.
2. Select the Month and Year using ▼▲ and press Ok.
3. Select the Day using ▼▲ and press Ok.
4. Hold Temp Until, Temp. Set & Hours are displayed.
To cancel seng and return to normal operaon press Ok.
Permanent Hold
Temp. is shown
above the
me on the display.
Time disappears
from the display.
Hold Temp. Unl is
shown above the
date on the display.
Boom right cycles
between the set
year and the room
temperature.

SERVICE AND WARRANTY
Guarantee: as shown on product identication label.
Any tampering or misuse will invalidate this guarantee.
This product must meet Waste Electronic and
Electrical Equipment Regulations (WEEE) for suitable
environmental recycling, recovery and/or disposal.
End of life products should be handled in line with local
regulations. Alternatively return end of life product to
Sangamo for correct disposal.
CUSTOMER CARE POLICY
As part of Sangamo’s continuous improvement
program, the company operates a Customer Care
policy. This means we welcome your comments and
complaints, as it can help us to improve our services
to you, our customer.
Due to our policy of continuous product improvement
and development, the specications in this guide may
be subject to change without prior notice.
Sangamo Limited
Industrial Estate, Port Glasgow,
Renfrewshire, PA14 5XG
Tel [phone]
Fax: [phone]
Email: [email protected]
Web: www.sangamo.co.uk
WEE/JH0069TY
CHANGING THE BATTERIES
When the Baery Low warning sign
appears on the display, replace the
baeries immediately.
Flip to open the baery compartment
on the plasc housing.
Upper compartment
2x 1.5v Alkaline AAA for transmier
Lower compartment
2x 1.5v Alkaline AAA for back light and
transmier
DO NOT USE RECHARGEABLE BATTERIES
143881 A
RECEIVER
If LED is permanently lit no RF
signal is being found. Heang will
turn o aer 10 minutes if no RF
transmission resumes. Aer the
RF signal is recognised the heang
schedule will connue.
This LED indicates if a signal
is being sent to the boiler to
turn on. Blue light indicates the
boiler should be ring.
Manual buon. If RF signal fails, for
example if the baeries in the thermostat
are at, this buon can turn the heang on
and o.