SANJIANG A9097B User manual

1
Version ： 30144000200413
A9097B Intelligent Sounder Beacon Base
Read through these instructions before using this device to ensure correct installation and use!
I. Overview
A9097B Intelligent Sounder Beacon Base is addressable , low power consumption and loop powered to reduce installation
cost. The Intelligent Sounder Beacon Base can be used with a detector. The detector can be mounted directly on the base.
It can be used with a bus-type fire alarm control panel. After receiving a start command given by the fire alarm control
panel following an accident, the Sounder Beacon Base will begin to work. At this moment, the Sounder Beacon Base will give
a dazzling visual alarm signal and a harsh audible alarm signal, to remind the persons on the scene of the accident, the fact that
a fire has occurred on the site, quickly and necessity to take related evacuation measures, thus preventing the fire accident from
becoming a major one.
The Sounder Beacon Base may be used to give audible alarms and flashing alarms at the scenes of accidents. It is
applicable to places like high-rise residential buildings, public places, hotels, amusement buildings, factories, shopping centers,
hospitals, schools, office buildings and stock exchanges, and particularly to the places with a low visibility or the possibility of
generation of smoke.
II. Product features
Meet EN54-3.
It is installed by rotating, it can be installed conveniently and reliably.
It uses multiple super bright red LEDs as light sources for visual display, ensuring a striking display effect.
Set the detector base and Sounder beacon as a whole, it can be equipped with A9030T smoke detector and A9020T
heat detector, single point connection for detector, sounder and LED beacon (saving on both time and installation
costs) , debugged and maintained conveniently.
III.Technical Specification
1. Executive Standard: EN54-3 Type A Sounder
2. Loop input: DC24V(20-28V), ≤2mA(monitoring status), ≤8mA(alarm status)
3. Power consumption: ≤0.2W@DC24V
4. Sound output: ≥73dB(A)@ 1m
5. Flash rate: 1~2Hz
6. Flash color: RED
7. Protection class: IP21C
8. Operating temperature: -10℃～+55℃Relative Humanity: ≤95% (non-condensing)
9. Material Body: Flame retardant PC/PC+ABS
10.Dimension: φ115mm×H44mm (with bracket) , See Fig.1
11. Weight: about 169g
2
Fig.1
IV. Use and engineering application
1. Wiring:See Fig.2.The Sounder Beacon Base is subject to a two-wire non-polarity connection: Terminals 1 and 3 are
respectively connected with the terminals L1 and L2 of the loop bus of a compatible fire alarm control panel.
Terminals 2 and 4 are respectively connected with the terminals 2 and 4 of A9020T(Heat Detector) or
A9030T(Smoke Detector).
TERMINALS TO NEXT DEVICE
1 PAIR FIRE CABLE
FROM CONTROL PANEL
1 PAIR FIRE CABLE
Fig.2
2. Coding address: The Sounder Beacon Base must be encoded address by a special coder (CODER-F900E) before the
installation. Fig.3 shows the wiring diagram of the Sounder Beacon Base and coder. After wiring, press the “#” key
to select “324” mode, set the coder with the coding function, then select the correct address number and press the
“RUN/STOP” key to complete the address code setup. (Note: See the User’s Manual of the coder for the detailed
operation.)
Fig.3

3
3. Mode coding: The mode of the Sounder Beacon base can be set by the coder. The wiring method of setting mode is
the same as the address coding. After wiring, press the "#" key to select "99A" mode, set the coder with the coding
function, then select the corresponding code in the following table and press the "RUN/STOP" key to complete the
mode setup. (Note:See the User’s Manual of the coder for the detailed operation.)
Mode Table
Mode Code
Sounder&Beacon 01
Sounder 02
4. Application: Fig.4 is a schematic diagram of the connection between multiple Sounder Beacon Base with a fire alarm
control panel.
Fig.4
V. Installation
Definitions of terminals (non-polarity Two-wire system) 1->Loop terminal (L1/L2) 3->Loop terminal (L2/L1)
Fig.5 Base and wiring diagram
1. Use two M4 screws to fix the A9097B bracket to ceiling via the two elliptic screw holes (see Fig.5) .
2. Twist the base onto the bracket (pay attention to aligning two arrow).
3. Connect the bus cables with the terminal 1&3.
4. If the Sounder Beacon Base is required to be tamper-proof,fix it with cross recessed pan head screws M3×9 thought
tamper-proof hole,and the detector is prevented from disassembly by structural changes(see Fig 6).
4
BRACKET
BUTTOM COVER
TOP COVER
CLAMP PLATE
4
CROSS RECESSED PAN HEAD
SCREWS M3
×
9
DETECTOR
R I B
KEY
Fig 6
VI.Sound Level Data (EN54-3 approved)
Tone: [email protected], Max Volume, dB(A)@1m
Angle Horizontal Vertical
Voltage 20V 28V 20V 28V
15° 82.0 85.0 82.7 85.4
45° 80.0 83.5 81.8 84.7
75° 82.1 85.3 80.2 83.3
105° 83.0 85.3 84.6 87.4
135° 83.0 85.9 81.2 83.7
165° 83.2 86.0 81.9 84.7
Address: 3/F, Guangcai Xintiandi Mansion, Nanshan Road, Nanshan District, Shenzhen, Guangdong, 518054, P.R.China
Tel：[phone] Fax：[phone] Website：http://www.sanjiang-security.com