Santec MONARCH CRYSTAL Series User manual

MONARCH CRYSTAL COLLECTION
##PART DESCRIPTION PART #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Complete Spout Assembly *
Complete LC Lever Handle Assembly *
Roman Tub Spout Flange *
Quick Connect Spout Shank & Hardware
Valve Body Mounting Hardware
Hot Cartridge
Cold Cartridge
Complete Hot Valve
Complete Cold Valve
Diverter Cartridge
Diverter Mounting Hardware
Complete Diverter
Hand Shower Mounting Hardware
Guide Tube *
Hand Shower Unit *
PS-5M00S
00LC
PH2210
P0416-LH
P0416-LC
P0493
P0494
P0510R
PM-Z11
Z-200-5
* Please specify the finish when ordering the part.
99
77
55
1010
1212
1313
22
66
11
88
Hand Shower Flange and Washer *
1414
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE PAGE 01
1515
1616
1717
P0510
Z-200-1
Z-200-2
17
18
19
Hand Shower Hose HS-600/ HS-700
44
KQ-5000S
22
33
20
21
Aerator Washer PM-356
Roman Tub Aerator without Restrictor PM-355
Aerator Housing * P0255L
Large Allen Key for Roman Tub Spout
22
2121
1155LC
ITEM NUMBER
ROMAN TUB FILLER WITH HAND HELD SHOWER - “LC” HANDLES
22
1818
1919
2020
2222
Medium Allen Key for Handle Trim
55
1111

INSTALLATION INSTRUCTIONS
FLUSH BOTH SUPPLY LINES BEFORE INSTALLATION
AFTER FLUSHING, SHUT OFF BOTH SUPPLY LINES
MINIMUM HOLE SIZE FOR THE SPOUT AND HANDLE TRIM IS 1 1/4” AND MAXIMUM IS 1 1/2”
SPOUT INSTALLATION
1
- Remove the Quick Connect Spout Shank and Mounting Hardware from the box.
Remove the mounting hardware (metal washer and brass lock nut) from the Quick Connect
Shank.
- From the top of the deck, slip the quick Connect shank with the brass plate through the
assigned spout hole.
- Secure the quick connect shank by putting the washer and locknut back on the shank.
Tighten the lock nut firmly.
2.
- Remove the faucet from the box.
- From the top of the deck, slip the spout (1) with the flange(3) onto the quick connect shank
top. Align the spout and tighten the set screw with the Large Allen Key (21) provided.
3
- Connect the spout shank to one of the outlet port (OUT) of the diverter valve after the diverter
valve is installed. **
Note: for better installation it is advisable to place silicone caulking around all holes on the top
of the deck
If the trim is ordered separately, please keep the shank protector on the quick connect shank
at all time to avoid damages to the unit.
HANDLE INSTALLATION
1.
- Using the medium Allen Key provided, loosen the handle set screw
- Unscrew the pre-assembled handle trim (2)and the top mounting hardware from the
valve body.
- Slip the valve body (8) or (9) up from the bottom of the tub through the appropriate hole next
to the spout.
- From tub top, insert the top mounting hardware back onto the valve. Do not tighten.
screw the handle bell of the handle trim (2) back onto the valve body. After the height of the
handle bell is set, unscrew the handle bell and tighten the mounting hardware firmly. Reinsert
the handle bell and screw it tight against the valve’s cartridge thread.
- Insert the handle back onto the valve stem and tighten the set screw using the medium Allen Key.
Make sure that the handles turns freely in both directions.
2
- Position the valve body side outlet towards the diverter valve (12) for easier pipe connection.
Align the handle lever and tighten lock nut (5) firmly. Repeat the same procedure for the
opposite side.
- Connect the water supply lines to the bottom inlets of the valve bodies. **
- Connect the valve body side outlet to the inlet (IN) of the diverter valve (12) after the diverter
is installed. **
PAGE 02
Metal washer
Brass lock nut
Metal washer
Brass lock nut
1155LC _ _
Brass plate
Large Allen Key
Fiber washer
Brass lock nut
Handle Bell
Medium Allen Key
Fiber washer
Brass lock nut
Handle

INSTALLATION INSTRUCTIONS
DIVERTER INSTALLATION
1
- Using the medium Allen Key (22) loosen the handle set screw
- Unscrew the pre-assembled handle bell and top mounting hardware of the diverter handle trim (2)
from the diverter (12).
- Slip the diverter valve body (12) up from the bottom of the tub through the appropriate hole.
- From tub top, insert the top mounting hardware back onto the valve. Do not tighten.
screw the handle bell of the handle trim (2) back onto the valve body. After the height of the handle bell
is set, unscrew the handle bell and tighten the top mounting lock nut firmly. Reinsert the handle bell and
screw it tight against the valve’s cartridge thread.
- Insert the handle back onto the valve stem and tighten the set screw using the medium Allen Key.
- Make sure that the handle turns freely in both directions.
** The spout, handle valve bodies and diverter can be connected with flex hoses (not provide by Santec) or copper pipe soldering.
Please note that when soldering connections, do not use excessive heat. Excessive heat can damage the joints increasing
probability of leakage.
HAND SHOWER INSTALLATION
1
- Slip the guide tube (15), flange (14) and the washer down from the top of the tub through
the appropriate hole. Slip the mounting hardware (13) from the bottom of the tub, first the
crimped metal washer then the brass lock nut. Tighten the lock nut firmly.
2
- Wrap Teflon seal tape around the threaded outlet end (OUT) of the diverter valve. Connect and
tighten the ½” female side of hose (17) onto the outlet.
- Slip the other end of the hose (3/8”) up through the guide tube (!5), connect and tighten the
hose to the hand shower unit (16).
WATER TEST
- Turn on the cold water supply.
- Use the handle from the faucet set to turn the valve on and off.
- Check for leaks. If water leaks from any of the connections merely tighten the connections
until the leak stops.
- Repeat the same procedure for the hot side
Metal washer
Brass lock nut
Plastic washer
Diverter
PAGE 03
1155LC _ _
Fiber washer
Brass lock nut
Handle Bell
Handle
Medium Allen Key
Fiber washer
Brass lock nut

HOT WATER
SUPPLY
COLD WATER
SUPPLY
From Diverter
to Hand shower 4-Port
Diverter
Hand
Shower
Tub
Spout
Hot
Valve
Cold
Valve
FROM HOT VALVE TO DIVERTER
FROM DIVERTER TO SPOUT
FROM COLD VALVE TO DIVERTER
Cold Valve
Hot Valve
IN
OUT
IN
OUT
INSTALLATION INSTRUCTIONS
PAGE 04
Santec Inc.
3501 Challenger Street, Torrance, CA 90503
Tel: [phone] Fax [phone]
www.santecfaucet.com 03/03
1155LC _ _