Santec Widespread 9220ED User manual

KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
WIDESPREADS
INSPECTED BY
*** NOTE: SHUT OFF WATER SUPPLY BEFORE BEGINNING INSTALLATION***
PAGE 01
COLLECTION
PLEASE READ THE INSTRUCTIONS COMPLETELY
BEFORE BEGINNING THE INSTALLATION.
MINIMUM HOLE SIZE FOR THE SPOUT AND
HANDLE TRIM IS 1 ¼” AND MAXIMUM OF 1 ½”
Brass lock nut
Tee connector & washer
SPOUT INSTALLATION
A- Remove tee connector and mounting hardware from the spout.
Apply a ring of silicone caulking around hole designated for spout.
DO NOT USE PLUMBERS' PUTTY WHICH CAN DAMAGE FINISH.
Insert spout through center hole of sink or countertop.
-From below slip notched washer and gasket over spout shank. Align
notched washer and gasket to allow pop-up rod to pas through.
Attach wing nut and brass lock nut.
Secure spout by tightening the two screws on wing nut.
Thread tee connector and washer to pout shank and tigfhten to seal
DO NOT TIGHTEN
HOSE
DO NOT TIGHTEN
HOSE

INSTALLATION INSTRUCTIONS
HANDLE TRIM INSTALLATION
HANDLE TRIMS ARE READY FOR DROP IN INSTALLATION.
DO NOT DISASSEMBLE.
Remove the valve body mounting hardware from the valve body.
Hot valve assembly “Red” to be mounted on left.
Cold valve assembly “Blue” to be mounted on right.
-Apply a ring of silicone caulking around the handle hole on the sink
countertop.
Slip valve through appropriate hole in sink or countertop.
Align handle with respect to the spout and tighten valve body locknut
until secure. Aim outlet hoses towards tee connector and attach securely
to avoid leakage.
PAGE 02
POP-UP DRAIN INSTALLATION
A- Remove decorative drain flange and drain plug from pop-up assembly.Apply a ring of silicone
caulking to underside of decorative drain flange. DO NOT USE PLUMBERS’ PUTTY, WHICH CAN
DAMAGE FINISH. Insert threaded end of the assembly up from below sink. Completely thread
drain body into decorative drain flange and align with ball rod hole facing back and tighten lock
nut from below. Insert drain plug into decorative drain flange with adjustable eye-screw facing back.
Attach ball rod washer and ball rod nut to horizontal ball rod and install into drain body. Do not over
tighten, bal rod must operate freely. Slide lift rod and knob through spout and from below the lift rod
strap and tighten thumbscrew. Gently push the horizontal ball rod down to place the drain plug in the up
position. Slip one leg of ball rod clip off horizontal ball rod and insert lift rod strap, reattach leg of ball
rod clip.
- Test pop-up for smooth operation and adjust if necessary.
Drain Plug
Drain Flange
Lift Rod Strap
Ball Rod
Drain Tube
Ball Rod Nut
Ball Rod Clip
Thumb Screw
Lock Nut
Washer
Gasket
Side hole
Lift Rod
FLUSH THE LINE
After all the connections have been made from inlet supplies to angle stop, remove the aerator. Open both hot and cold valves. Slowly open angle
stop from below and flush the lines for approximately 45 seconds to clean any debris. Turn off the water and reinsert aerator.
WIDESPREADS
COLLECTION
SANTECSANTEC
rubber washer
SANTECSANTEC
Fiber washerFiber washer
Brass lock nutBrass lock nut
DO NOT USE PLUMBERS' PUTTY WHICH CAN DAMAGE FINISH

PAGE 03
SANTEC LIFETIME LIMITED WARRANTY
1. Finishes: Santec Polished Chrome and Polished Orobrass finishes carry a Lifetime Limited
warranty against manufacturing defects and tarnish to the original purchaser with the exclusion of
kitchen drain assemblies which, due to the nature of their use, are not warranted. Santec
recommended custom finishes carry a ten (10) years limited warranty against manufacturing
defects and tarnish to the original purchaser with the exclusion of kitchen and pop -up drain
assemblies which, due to the nature of their use, are not warranted.
2. Cartridges: Santec Cartridges carry a lifetime limited warranty against manufacturing defects for the
life of the product to the original purchaser.
3. Parts: Santec parts carry a Ten (10) year limited warranty against manufacturing defects, to the
original purchaser.
4. Warranty exclusions and limitations : This warranty does not cover: damage due to negligence,
accident, abuse, improper installation, or improper maintenance such as, but not limited to: heat from
soldering during installation, the use of plumbers putty, damage from tools used during installation,
the use or exposure to chemicals or cleaning products either abrasive or non abrasive or the use of
any cleaning tool or product other than a soft, clean cloth. This warranty does not cover: changes in
the finish or in the product due to normal wear or aging and does not cover any product or parts
which have been altered or used in a manner not typical for the product. This warranty does not
cover and Santec will not be held liable for damage to products caused by the freight carrier
and a claim should be made immediately to the freight carrier should this occur. This warranty
does not cover any cost involved in the installation, repair, or replace ment of any Santec product or
part. This warranty does not cover and Santec will not be held liable for any loss, damages, or
expenses, incidental or consequential whatsoever, originating from the purchase, installation, use,
repair, failure, or replaceme nt of any Santec product or part, as allowed by law. The product or
components of the covered product will either be repaired, refinished or replaced, at the sole
discretion of Santec. Santec reserves the right to examine any product claimed defective pr ior to
any warranty claim being accepted or processed, at its sole discretion. This warranty gives you
specific legal rights and you may have other rights which may vary from state to state.
Effective 01/01/03 - Replaces and supersedes any previously issued warranty.
FINISH CARE INFORMATION
For clear coated or enamel color finishes:
We recommend that all faucets, drains, etc. be
gently wiped dry with a soft cloth after use to avoid
water spotting and water deposit buildup. A mild
liquid hand soap, s uch as Ivory may be used
occasionally if desired. Use of a non -abrasive
carnauba wax will add protection to the finish and
should be used if the faucets will not be dried after
use. Santec Orobrass kitchen products are clear
coated.
For non-clear coated and specialty finishes:
We recommend that all faucets, drains, etc. be
gently wiped dry with a soft cloth after use to avoid
water spotting and water deposit buildup. Use of a
non-abrasive carnauba wax is required
occasionally.