Santos 54 Operating instructions


*408.065 - *408.066
Model no 54
DRINK MIXER N° 54
USER AND MAINTENANCE MANUAL
IMPORTANT: documents included in this manual to be kept:
• “CE” COMPLIANCE DECLARATION
• WARRANTY CERTIFICATE
408065-66 en ma 2010.12 1/17

98154 US 2.2 - 12 2010 2 / 17 www.santos.fr
CONTENTS
“CE” COMPLIANCE DECLARATION........................................................................................3
IMPORTANT SAFEGUARDS ........................................................................................................4
IMPROPER USE .............................................................................................................................4
ELECTRICAL CONNECTION:.......................................................................................................4
USING FOR THE 1st TIME:...........................................................................................................5
RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE..........................................5
YOUR DRINK MIXER N°54...........................................................................................................6
USING THE APPLIANCE...............................................................................................................6
START-UP:......................................................................................................................................6
IDLE POSITION..............................................................................................................................7
CLEANING:.....................................................................................................................................7
STORAGE:.......................................................................................................................................7
MAINTENANCE...............................................................................................................................8
CHANGING THE MIXING HEADS AND DEFLECTOR:..............................................................8
Spare Parts:.....................................................................................................................................8
FAULT FINDING..............................................................................................................................9
The appliance does not start.........................................................................................................9
The appliance stops suddenly after operating for a long time: the motor is very hot..................9
The machine stops because of an overload:.................................................................................9
The motor runs all the time even without the cup on the cup stand............................................9
The motor is running but the speed variation is not working......................................................9
TECHNICAL SPECIFICATIONS................................................................................................10
REFERENCE TO STANDARDS....................................................................................................10
Wiring diagram 110-120V~ 50/60Hz ............................................................................................11
Wiring diagram 220-240V~ 50/60Hz ............................................................................................12
FIGURES.......................................................................................................................................13
WARRANTY CERTIFICATE .....................................................................................................17
APPLIANCE IDENTIFICATION PLATE ................................................................................17
408065-66 en ma 2010.12 2/17

98154 US 2.2 - 12 2010 3 / 17 www.santos.fr
“CE” COMPLIANCE DECLARATION
THE MANUFACTURER:
SANTOS SAS - 140-150, Av. Roger SALENGRO 69120 VAULX-EN-VELIN (LYON)
FRANCE
declares that the appliance intended for the professional market described below:
Description: DRINK MIXER
Type number: 54
complies with:
xthe statutory provisions defined in appendix 1 of the European "machines" directive
n°2006/42/CE and the national legislation transposing it
xthe statutory provisions of the following European directives and regulations:
oN° 2006/95/CE (low voltage directive)
oN° 2004/108/CE (EMC directive)
oNo. 2002/95/CE (RoHS directive)
oNo. 2002/96/CE (WEEE directive)
oN° 1935/2004/CE (regulation) relating to materials and articles intended to
come into contact with foodstuffs
Harmonised European standards used to give presumption of conformity with the essential
requirements of the above-mentioned directives:
xNF EN ISO 12100 -1 and 2:2004: Safety of machinery - General principles for
design
xNF EN 60204-1: 2006 : Safety of machinery - Electrical equipment of machines-
General requirements
xNF EN 1672-2: 2005, Food processing machinery – Basic concepts – Hygiene
requirements
xNF EN 60335-1: 2003 : Household and similar electrical appliances. Safety.
xNF EN 60335-2-64 :2004 : Particular requirements for commercial electric kitchen
machines
Drawn up in VAULX-EN-VELIN on: 01/12/2010
Signatory’s position: CHIEF EXECUTIVE OFFICER
Signatory’s name: Aurélien FOUQUET
Signature:
408065-66 en ma 2010.12 3/17

98154 US 2.2 - 12 2010 4 / 17 www.santos.fr
IMPORTANT SAFEGUARDS
When using, cleaning or maintaining the machine, always follow these instructions:
Read all instructions
IMPROPER USE
1. This appliance is not meant to contain solids such as ice cubes, frozen
foodstuffs or products, dry products that would jam the motor or damage the
mixing heads.
The following solids are accepted in a quantity of less than 20% with 80% liquid:
xCrushed ice
xPowder (soluble coffee, milk,...)
xBalls of soft ice cream.
The mixing heads are not designed to grind, crush or cut but only to mix or emulsify
liquid or smooth foodstuffs or products.
2. Never add products or foodstuffs to the cup during preparation or operation.
3. Never exceed the maximum filling level of the cup which may cause
products or foodstuffs to overflow during preparation.
Maximum capacity of cup: 0.560 liter or 19.5 Oz.
4. Place the appliance on a smooth, non-sloped surface to ensure it is stable
and for the suction feet (14) to adhere properly.
5. You are not advised to operate the appliance with an empty cup.
6. The appliance should neither be cleaned in a jet of water nor with a high
pressure spray.
7. For electrocution risk protection reasons, never plunge the base into water or
any other liquid.
8. Unplug the appliance before carrying out any work on it: cleaning, maintenance
or repair.
9. The use of spare parts other than certified SANTOS original parts is prohibited.
ELECTRICAL CONNECTION:
The appliance is available in with a choice of two voltages for the power supply
x220-240V 50/60 Hz single phase
x110-120V 50/60 Hz single phase
Line protection: the appliance should be connected to a standard 2-pole + earth electric
socket. The installation should be fitted with an RCD and a fuse rated at 16A. or the
Note: You will find it easier to understand the next few paragraphs if you refer to
the diagrams at the end of this manual.
!
408065-66 en ma 2010.12 4/17

98154 US 2.2 - 12 2010 5 / 17 www.santos.fr
relevant value according to local electrical codes, taking into account the unit rated
current. The appliance must be earthed
CARE:
xBefore connecting the machine, check that the mains electrical voltage
is the same as the voltage for your appliance. Its value is shown:
¾either on the identification plate under the machine.
¾or on the identification plate on the last page of this manual.
xIf the power cable (10) is damaged, it should be replaced by a special
assembly available from approved SANTOS dealers or from SANTOS.
USING FOR THE 1st TIME:
Carefully clean the parts in contact with the food (Fig. A, Fig. B and Fig. C).
xWash the two cups (stainless steel (1) and plastic (2)) with standard washing up
liquid or in the dishwasher.
xWash the flexible mixing head (4) supplied separately.
xTo wash the mixing head (3) and deflector (5) which are assembled on the
appliance, take them down as follows:
-Hold the deflector (5) and unscrew the mixing head (3).
xWash the mixing head (3) and deflector (5) with standard washing up liquid or in the
dishwasher.
xPut the deflector (5) and mixing head (3) back after washing as follows:
-Bring the two flat surfaces of the deflector (5) in register with those of the motor
shaft (6).
-Screw on the mixing head (3).
RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE
This equipment is marked with the selective sorting symbol relating to
wastes from electrical and electronic equipment. It signifies that this product
should be taken over by a selective collection system conforming to the
Guideline 2002/96/EC (WEEE) – part Professional Equipment – so that it
can be either recycled or dismantled in order to reduce any impact on the
environment.
For more information, please contact your Retailer or the SANTOS.
For eliminating or recycling components of equipment, please contact a specialized
company or contact SANTOS.
The electronic products not undergoing a selective sorting are potentially dangerous for
the environment.
The damaging materials should be eliminated or recycled according to the regulations in
force.
!
408065-66 en ma 2010.12 5/17

98154 US 2.2 - 12 2010 6 / 17 www.santos.fr
YOUR DRINK MIXER N°54
xThe drink mixer N° 54 is designed especially for bars, cafés, hotels, restaurants,
cocktail bars, canteens, stores selling fruit juices, cake stores, ice cream parlors.…
xThe drink mixer N° 54 is designed to mix and emulsify different foodstuffs in liquid
and smooth form.
xIt is ideal for making:
odrinks (fruit, vegetable cocktails, punches, syrups,...)
odrinks with ice cream or crushed ice,….
oIce creams, milk shakes, smoothies,…
xThe appliance comprises a motor unit fixed to a cast aluminum column.
2 cups are supplied to hold the products: one stainless steel cup and one see-through
plastic cup. The top part of the cups has been designed for quick fitting on the cup stand
and start up of the appliance.
USING THE APPLIANCE
START-UP:
1. Plug in the appliance.
2. Turn the motor speed knob (7) anti-clockwise to the low speed position (small mark
on the knob in front of the operator).
3. Put a small amount of liquid (approximately 0.25 liter) into the bottom of the
stainless steel (1) or plastic cup (2).
4. Place the stainless steel (1) or plastic cup (2) on the cup stand (8) (operating
position) (Fig. A) and the appliance starts up immediately at low speed.
5. Turn the motor speed knob (7) clockwise to high speed (big mark on the knob in
front of the operator).
6. Go back to low speed by turning the motor speed knob (7) anti-clockwise to the low
speed position (small mark on the knob in front of the operator).
-You have now tested the whole speed range.
7. Take the cup off the cup stand and the appliance will stop.
8. Repeat operations 4, 5, 6, and 7 with the second cup, if required.
TAKE NOTE:
1. For the first few operations, you are advised to start at low speed to
prevent splashing (cup too full).
2. You are not advised to operate the appliance with no liquid inside the
cup.
408065-66 en ma 2010.12 6/17

98154 US 2.2 - 12 2010 7 / 17 www.santos.fr
IDLE POSITION
Placing the cup (1) or (2) in the second position (lower position) on the cup stand (8) puts
it into the idle or stop position (Fig. E)
NOTE:
Emulsions or mixes are usually obtained in under 1 minute.
TAKE NOTE:
1. The appliance stops when the cup (1) or (2) is removed from its stand
(8), however, a rotation movement does persist for a few seconds due
to motor inertia: do not allow the cup to be off center so as not to
damage the mixing head (3) or (4) and deflector (5).
2. Wait for the motor to stop before removing the cup completely and
avoid splashes.
CLEANING:
IMPORTANT:
xWhen cleaning, stop the appliance and unplug the appliance’s power cord
(9).
xThe appliance must not be cleaned with a water jet, pressurized water or
immersed.
xIf, during preparation or incorrect handling, food or splashes have got into
the cup positioning area or on the cup stand (8), you are advised to clean
this area quickly with clean water and check the cup presence detection
finger (10) is working properly.
You are advised to clean the appliance as soon as you have finished using it.
It will be easier to clean if you do not wait until food has dried in the cup, on the mixing
head or deflector.
All these parts:
xstainless steel cup (1)
xplastic cup (2)
xmixing head (3)
xmixing head (4)
xdeflector (5)
must be cleaned with standard washing up liquid or in the dishwasher.
Do not use abrasive products that could damage the parts.
STORAGE:
The stainless steel (1) and plastic cups (2) can be stacked for storage purposes.
408065-66 en ma 2010.12 7/17

98154 US 2.2 - 12 2010 8 / 17 www.santos.fr
MAINTENANCE
Before any servicing of the appliance, it is essential to unplug the appliance from the
mains supply (9).
This machine requires no particular maintenance because the bearings are lubricated for
life.
If any intervention is necessary to replace parts subject to wear, such as the mixing heads,
the deflector, electrical or other components, please refer to the parts list (see the
exploded view at the end of this manual).
CHANGING THE MIXING HEADS AND DEFLECTOR:
Taking down the mixing head (3) or (4) and deflector (5)(Fig. A, Fig. B and Fig. C):
xUnscrew the mixing head (3) or (4) by hand holding the deflector (5) to
stop the motor shaft (6) from turning.
Mounting the deflector (5) and mixing head (3) or (4)(Fig. A, Fig. B and Fig. C):
xPut back the deflector (5) making the two flat surfaces register with the two
flat surfaces of the motor shaft (6). Screw on the mixing head (3) or (4) by
hand.
Spare Parts:
IMPORTANT:Use of spare parts other than certified original SANTOS
parts is prohibited
Please quote the following when ordering spare parts (see references in the exploded
view at the end of this manual):
xtype
xappliance’s serial number
xelectrical specifications given underneath the appliance.
!
408065-66 en ma 2010.12 8/17

98154 US 2.2 - 12 2010 9 / 17 www.santos.fr
FAULT FINDING
Identifying the cause of appliance stoppage precisely.
The appliance does not start
Check:
xthe mains supply, the condition of the supply cord (9).
xthe cup (1) or (2) is fitted properly on the cup stand (8). Check in particular that the
top part of the cup is not damaged.
xthe cleanness of the cup (1) or (2) positioning area.
The appliance stops suddenly after operating for a long time: the motor is very hot
The motor is protected by an integral thermal protection. In the event of overheating, the
motor stops automatically.
xSwitch off the appliance (unplug the power supply cord (9)).
xWait for the motor to cool down (20 to 45 minutes).
xPlug back in and resume work by placing the cup (1) or (2) on the cup stand (8).
The machine stops because of an overload:
If the motor is jammed (foreign body, object or hard foodstuffs blocking the mixing head),
the appliance stops automatically.
xSwitch off the appliance (unplug the power supply cord (9)).
xTake the stainless steel (1) or plastic cup (2) off the cup stand (8) and place it on a
worktop.
xRemove the objects or hard bits blocking the mixing head.
xReset the thermal protection device (10) underneath the appliance manually (Fig. F).
xPut the products or foodstuffs to be processed back in the cup.
xPlug back in and resume work by placing the cup (1) or (2) on the cup stand (8).
The motor runs all the time even without the cup on the cup stand
Check:
xthe operation of the cup detection finger (10) in the cup stand (8).
xthe cleanness of the cup presence detection finger area and clean this area if
required (Fig. D).
The motor is running but the speed variation is not working
Check:
xgo through the whole speed range of the motor with the motor speed knob (7) (Fig.
A) several times.
408065-66 en ma 2010.12 9/17

NOTE:
If one of these problems persists, disconnect the electric power supply (unplug the power
supply cord (9)) and call on someone from the maintenance department or contact an
approved SANTOS dealer.
TECHNICAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS (1)
Model 54 Single phase
Supply voltage .(V) 220-240 100-120
Frequency (Hz) 50/60 50/60
Motor: Rating
Power input (W) 120 120
Speed: Minimum
Maximum (rpm) (rpm) 8 000 8 000 16 000 16 000
Cup capacity (L) 0.560
Dimensions: Height (mm) 530
Width (mm) 182
Depth (mm) 186
Weight: Net weight (kg) 6
Weight including packing (kg) 7
Noise: (2) (dBA) 63
(1) These ratings are provided as a rough guide. The exact electrical specifications can
be found on the rating plate.
(2) Noise level measured with sound pressure appliance in operation 1 m from its
centerline in accordance with standard EN 31201.
REFERENCE TO STANDARDS
xCE (Europe)
xGS (Germany) checked by the LNE National Test Laboratory.
xUL (USA) and cUL (Canada).
xNSF (USA).
408065-66 en ma 2010.12 10/17

98154 US 2.2 - 12 2010 11 / 17 www.santos.fr
Wiring diagram 110-120V~ 50/60Hz
Y
ellow or white
Black
Red
AMPEREMETRIC
THERMAL
PROTECTOR
TACHYMETRIC
ELEMENT
POTENTIOMETER
ELECTRONIC
BOARD
Yellow or white
Black
Red
Y
ellow or white
Black
Red
Brown
Blue
Brown
Blue
Black
Black
L
N
MM
~
Brown
Blue
M
CUP
PRESENCE
SWITCH
T
Green/
y
ellow
408065-66 en ma 2010.12 11/17

98154 US 2.2 - 12 2010 12 / 17 www.santos.fr
Wiring diagram 220-240V~ 50/60Hz
Blue
Brown
Brown
Black White
Y
ellow or white
Black
Red
AMPEREMETRIC
THERMAL
PROECTOR
TACHYMETRIC
ELEMENT
POTENTIOMETER
ELECTRONIC
BOARD
Yellow or white
Black
Red
Y
ellow or white
Jaune
Black
Red
Brown
Blue
Black
White
Red
Red
L
N
MM
~
Brown
Blue
M
CUP
PRESENCE
SWITCH
T
Green/Yellow
PARASITE
SUPPRESSOR
FILTER
408065-66 en ma 2010.12 12/17

98154 US 2.2 - 12 2010 13 / 17 www.santos.fr
FIGURES
1
2
4
3
5
7
FIG
A
FIG B
11
- SLOWER + FASTER
SCREW UNSCREW
11
8
12
7
12
408065-66 en ma 2010.12 13/17

7
11
8
10
FIG C
FIG D
12
8
6
11
408065-66 en ma 2010.12 14/17

98154 US 2.2 - 12 2010 15 / 17 www.santos.fr
11
8
1
FIG E
2
408065-66 en ma 2010.12 15/17

98154 US 2.2 - 12 2010 16 / 17 www.santos.fr
ITEM Description
1 Stainless steel cup
2 Plastic cup
3 Mixing head
4 Flexible mixing head
5 Deflector
6 Motor shaft
7 Adjustment knob
8 Cup stand
9 Power supply cord
10 Cup detection finger
11 Base column
12 Motor unit
13 Rubber foot
14 Suction foot
15 Overload protector
9
13 14
11
15
13 FIG F
408065-66 en ma 2010.12 16/17

WARRANTY CERTIFICATE
WARRANTY
APPLIANCE IDENTIFICATION PLATE
SPECIMEN
For all the documents not delivered
with the appliance.
Printed, Faxed, Downloaded
Since the 01.01.95, all our appliances comply with CE and possess the CE label. Our guarantee is of
12 months from the manufacturing date mentioned on the descriptive plate. Warranty is strictly
limited to the free replacement of any part of origin recognized by us as defective due to a defect or
building default and identified as belonging to the concerned appliance. Warranty does not apply to
damages resulting from installation or use non-complying with our appliance data sheet (user’s
manual) or in case of an evident lack of maintenance or disrespect of elementary security electric
rules. It does not apply in case of regular wear and tear.Any replacement of parts under warranty will
be realized after return of the defective part in our workshops, postage paid, supported by a copy of
a conformity statement on which appears the serial number of the appliance. Every appliance is
equipped with a descriptive plate conforming to the EC recommendations and of which a duplicate
exists in the conformity statement (serial number, manufacturing date, electrical characteristics …).
In case of serious damage judged repairable only in our workshops, and after prior consent from our
departments, any appliance under guarantee is sent by the Distributor, carriage paid. In case of
repairs or reconditioning of appliances not under guarantee, the round trip transport is payable by the
distributor. The parts and workforce are invoiced at the current rate. A preliminary estimate can be
supplied.
Coffee grinder not using SANTOS original burrs are not taken under guarantee. The warranty
conditions, repairs, reconditioning, of the espresso coffee grinder are the object of a specific note.
Our guarantee does not extend to the payment of penalties, the repair of direct or indirect damages
and notably to any loss of income resulting from the nonconformity or the defectiveness of products,
SANTOS's global responsibility being limited to the sale price of the delivered product and to the
possible repair of the defective products.
In case of revelation of an imperfection during the warranty period, the Distributor has to, unless a
different written agreement of SANTOS, indicate to his customer to stop any use of the defective
product. Such a use would release SANTOS of any responsibility.
408065-66 en ma 2010.12 17/17