Sanus Systems NFCDII User manual

Assembly Instructions for Model: NFCDII
Thank you for choosing a Sanus Systems Natural Media Tower. The Model
NFCDII is designed to keep your collection clean and organized by storing up
to 430 CDs or 230 DVDs, all in one convenient location.
If you do not understand these directions, please contact Sanus at 800.359.5520
or www.sanus.com. Check carefully to make sure that there are no missing or
defective parts. Our customer service representatives can quickly assist you
with assembly questions, and missing or damaged parts. Replacement parts
for products purchased through authorized dealers will be shipped directly to
you. Never use defective parts. Improper assembly may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly
specied by Sanus Systems. Sanus Systems can not be liable for damage
or injury caused by incorrect assembly, or incorrect use. Please call Sanus
Systems before returning products to the point of purchase.
Required Tools: Rubber mallet or hammer, phillips screwdriver, and an
adjustable wrench.
Supplied Parts List: (Not to Scale)
NFCDII Top - A
Qty. 1
Glass Shelves - H
Qty. 14
NFCDII Base - B
Qty. 1
Steel Tube - G
Qty. 1
Center Support - E
Qty. 1
Side Panels - F
Qty. 2
NFCDII Back Leg - C
Qty. 1
NFCDII Front Leg - D
Qty. 1
SANUS Name Plate - I
Qty. 1
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 02.28.06 (000011)
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Supplied Hardware: (Full Size)
Step 1 - Insert Decorative Face Bolts into Front Leg
Insert the Decorative Face Bolts (O) into the Front Leg (D) making sure they are ush with the Front leg. If necessary, the
rubber mallet may be used to lightly tap them into place.
Diagram 1
Cam - J
Qty. 4
Cam Pin - K
Qty. 4
Plastic Dowel - L
Qty. 4
Screw - M
Qty. 4
Allen Bolt - N
Qty. 1
Decorative Face Bolt - O
Qty. 3
Nut - P
Qty. 2
Washer - Q
Qty. 2
Shelf Pin - R
Qty. 56
Allen Screw - S
Qty. 2
Allen Wrench - T
Qty. 1
O
D

Step 2 - Secure Steel Tube to Front Leg
Lay the Front Leg (D) face down on a soft surface with the threads of the Decorative Face Bolts (O) facing up; then, place
a Washer (Q) over the middle Decorative Face Bolt, and thread the Steel Tube (G) onto it. Firmly hand tighten the Steel
Tube.
Diagram 2
Step 3 - Secure Front Leg to NFCDII Base
Attach the Front Leg (D) to the NFCDII Base (B) by inserting the two outer Decorative Face Bolts (O) through the two
holes of the NCFDII Base and securing with two Nuts (P). Use the adjustable wrench to rmly tighten the two Nuts.
Diagram 3
G
D
Q
D
B
O
P
P
O

Step 4 - Secure Back Leg to Tube and NFCDII Base
Place a Washer (Q) between the Tube (G) and the Back Leg (C); then, using an Allen Bolt (N) secure the Back Leg to the
Tube.
Using the two Allen Screws (S), secure the Back Leg (C) to the NFCDII Base (B).
Diagram 4
Step 5 - Insert Cam Pins into Side Panels
There are two holes that are centered on each side of the Side Panels (F), and 12” [304.3 mm] from each end. Using the
phillips screwdriver, screw Cam Pins (K) into the two holes of each Side Panel taking care not to over tighten the Cam
Pins.
Diagram 5
SN
B
C
Q
K
F
F
G

Step 6 - Insert Cam into Center Support.
Place a Cam (J) into each of the four holes in the Center Support (E).
NOTE: Each Cam has an arrow on it. Using a phillips screwdriver align each Cam so the arrow is pointing toward
the small hole on the edge of the Center Support (See Detail - A).
Diagram 6
Step 7 - Secure Side Panels to Center Support.
The Cam Pins (K) installed in each Side Panel (F) line up with the small holes in the edge of the Center Support (E). The
top of each Side Panel is smooth and the bottom has a notch routed in the inside edge.
Attach a Side Panel to each side of the Center Support and using a phillips screwdriver, rotate each Cam (J) one-third turn
clockwise until secure (See Detail - B).
Diagram 7
Small Hole
Cam Hole
Top
Smooth
Bottom
Notched
K
J
F
F
E
Cam - J
E
Cam - J
Small
Hole
Detail - A
Detail - B