Sanyo VCC-6975 User manual

INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
VCC-6975P
COLOUR CCD camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
About this manual
Before installing and using the camera, please read this
manual carefully. Be sure to keep it handy for later reference.
Über diese Bedienungsanleitung
Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der
Kamera zuerst diese Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen auf.
A propos de ce manuel
Avant d’installer et d’utiliser la caméra, veuillez lire ce
manuel attentivement. Gardez-le à portée de main
pour toute référence ultérieure.
L53R2/XE GB 2000, 3, 31

Depending on the conditions of use, installation and environment, please
be sure to make the appropriate settings and adjustments. If you need
help with installation and/or settings, please consult your dealer.
CONTENTS
PRECAUTIONS 2
PARTS NAMES 3
CONCERNING AUTO-IRIS LENSES 6
MOUNTING THE LENS 7
CONNECTIONS 9
USING THE MENU SCREEN 12
•Notes concerning the menu settings 13
•LANGUAGE setting 14
•CAMERA ID setting 15
•SYNC settings 17
AInternal synchronization setting (INT) 17
BPower supply synchronization setting (L - L) 18
CExternal sync setting (VBS) 19
•IRIS setting (BLC, SENSE UP) 21
AAI (Auto Iris) mode setting 21
BEI (Electronic Iris) mode setting 26
•WHITE BALANCE setting 27
AAutomatic color temperature tracking setting (ATW) 27
BPush-lock white balance adjustment (AWC) 30
CManual white balance setting (MWB) 31
•Electronic SHUTTER setting 32
AFor SHORT mode 33
BFor LONG mode 34
•MOTION setting 35
ADIRECTION setting 37
BSIZE setting 38
CMASKING setting 40
DSENSITIVITY setting 42
EZOOM setting 43
FINTERVAL setting 44
GALARM SIGN setting 44
•Motion detector setting example 45
•OPTION settings 48
AAPERTURE setting 49
BAGC setting 50
CGAMMA setting 50
DZOOM setting 51
EMIRROR setting 55
FRS-485 setting 55
GINITIAL setting 57
OPERATIONS USING THE SYSTEM CONTROLLER 58
MENU DISPLAY 61
TROUBLESHOOTING 63
SPECIFICATIONS 64
ACCESSORIES 66
FEATURES
•Built-in interline transfer method /3" CCD, approx. 470,000 picture
elements
•High sensitivity, minimum required illumination is .4 lux (F .2)
•Horizontal resolution, more than 480 TV lines
•Digital motion detector with trigger output function
•Digital zoom with pan/tilt functions (up to X8)
•Up to 32 times electronic sensitivity function
•Equipped with connectors for AC 24 V and DC 2 V power supply
•RS-485 (SSP protocol) connector for remote controller (sold separately)
connection
L53R2/XE GB 2000, 3, 3
English 1

PRECAUTIONS
In case of problem
Do not use the camera if smoke or a strange odour comes from the
unit, or if it seems not to function correctly. Disconnect the power
cord immediately, and consult your dealer (or a Sanyo Authorized
Service Centre).
Do not open or modify
Do not open the cabinet, as it may be dangerous and cause damage
to the unit. For internal settings and repairs, consult your dealer (or a
Sanyo Authorized Service Centre).
Do not put objects inside the unit
Make sure that no metal objects or flammable substance get inside
the camera. If used with a foreign object inside, it could cause a fire,
short-circuits or damages.
If water or a liquid gets inside the camera, disconnect the power cord
immediately, and consult your dealer (or a Sanyo Authorized Service
Centre). Be careful to protect the camera from rain, sea water, etc.
Be careful when handling the unit
To prevent damages, do not drop the camera or subject it to strong
shock or vibration.
Install away from electric or magnetic fields
If installed close to a TV, radio transmitter, magnet, electric motor,
transformer, audio speakers the magnetic field they generate will
distort the image.
Protect from humidity and dust
To prevent damages to the camera, do not install it where there is
greasy smoke or steam, where the dampness may get too high, or
where there is a lot of dust.
Protect from high temperatures
Do not install close to stoves, or other heat generating devices, such
as spotlights, etc., or where it could be subject to direct sunlight, as
that could cause deformation, discoloration or other damages.
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may raise to high levels.
Install where the temperature range will stay between – 0˚C and
50˚C. (no condensation)
Cleaning
•Dirt can be removed from the cabinet by wiping it with a soft
cloth. To remove stains, wipe with a soft cloth moistened with a
soft detergent solution and wrung dry, then wipe dry with a dry
soft cloth.
•Do not use benzine, thinner or other chemical product on the
cabinet, as that may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes in
contact with the cabinet for a long period of time, as that may
cause damage or paint peeling.
ENGLISH
L53R2/XE GB 2000, 3, 3
2 English

PARTS NAMES
1Power indicator (POWER)
Comes on when the power to the camera is on.
2Video output connector (VIDEO OUT: BNC type)
Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.
NOTE: When using this connector, the supplied clamping core (A) must be installed on the coaxial cable, to
prevent electromagnetic interference from the other connected devices.
324 V AC or 12 V DC input terminal (AC 24 V, DC 12 V, GND)
4Y/C OUT connector (4 pin)
Separate Y (luminance) and C (chroma) signals are output from this terminal.
A better picture quality is obtained if the monitor or VCR is connected to this connector.
1Y signal ground 2C signal ground
3Y signal: .0 Vp-p, 75 ohms, unbalanced, negative sync
4C signal: 0.3 Vp-p, 75 ohms, unbalanced
5RS-485 control push-lock terminal (RS485, G, B, A)
A: Twisted-pair cable terminal
B: Twisted-pair cable terminal
G: Ground terminal
6External sync composite video signal input connector (VBS IN: BNC type)
Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite
signal of a video distributor.
NOTE: When using this connector, the supplied clamping core (A) must be installed on the coaxial cable, to
prevent electromagnetic interference from the other connected devices.
7Alarm output terminal (ALARM, C, A)
A: Alarm C: Common
1
6
2
3
4
7
5
12
43
L53R2/XE GB 2000, 3, 3
English 3

PARTS NAMES
8Camera setup section (under the cover)
To access the controls, loosen the cover fixing screw A, then remove the cover.
aAddress setting switch (RS485 ADDRESS) . . . See page 56
bTerminater switch (TERMINATE) . . . . . . . . . . See page 56
cAuto iris lens switch (A I LENS) . . . . . . . . . . See page 6
9Lens iris output connector (LENS)
This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens.
FMenu setting button (SET)
Connect the camera to the monitor, then press the SET button for about 3 seconds to display the on-screen
menu.
GCursor button (CURSOR)
j: Press this button to move the cursor up.
c: Press this button to move the cursor to the right, or to turn the settings ON/OFF etc.
d: Press this button to move the cursor to the left, or to turn the settings ON/OFF etc.
l: Press this button to move the cursor down.
8
9
A
F
G
a b c
L53R2/XE GB 2000, 3, 3
4 English

PARTS NAMES
HLens mount cap
The cap is installed to protect the lens mount section.
Remove the lens mount cap before installing a lens (sold separately).
IFlange-back adjustment screw (FLANGE BACK ADJ) (See page 8)
JFlange-back lock screw (FLANGE BACK LOCK)
KCamera installation bracket
The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the
longer screws and install the shorter screws on the opposite side to seal the openings.
1Shorter screws: M3 x 4
2Longer screws: M3 x 6
3Camera mounting screw hole: 1/4"-20 UNC
CAUTION:
When installing the camera bracket, select a location that can support the total weight of the
camera and accessories
1232
1
K
HJ
I
L53R2/XE GB 2000, 3, 3
English 5

CONCERNING AUTO-IRIS LENSES
DC type auto-iris lens
A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is
referred to as DC type coil lens or DC type non-amplifier lens.
(Set the A I LENS switch to the DC position.)
VIDEO type auto-iris lens
A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is
referred to as EE amplifier type lens.
ALC (Automatic Light Control) and LEVEL volume level controls are available on the lens for iris adjustments.
(Set the A I LENS switch to the VIDEO position.)
Compatible auto-iris lenses
1/3 inch Sanyo DC type lens VIDEO type lens
VCL-CS8LY: Standard angle, f= 8 mm Standard angle, f= 9 mm
VCL-CS4LY: Wide angle, f= 4 mm Telephoto angle, f= 2 mm
VCL-CS2LY: Ultra-wide angle, f= 2.8 mm Greater telephoto angle, f= 6 mm
If using a VIDEO type auto-iris lens
•Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume should be turned
all the way to Av (Average).
•Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL
volume on the lens casing to correct.
DC
VIDEO
A. I.
LENS
L53R2/XE GB 2000, 3, 3
6 English

MOUNTING THE LENS
Please use a DC type auto-iris lens (sold separately)
Checking the lens mount
Do not use lenses with a length L more than 5 mm. If not, that may damage the camera and prevent
proper installation.
1Remove the lens mount cap from the camera
2Install the auto-iris lens
CS mount type lens
Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.
C mount type lens
To allow for flange-back adjustment, install the supplied C-mount adaptor on the lens mount, then
carefully align the lens mount with the camera opening and turn the lens slowly to install it.
3Connect the lens plug to the lens iris output connector (LENS) on the side of the camera
When using lenses from other makers, the plug shape may not correspond to the terminal on the camera.
In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug
according to the diagram. (Refer to page 8.)
NOTE: When using an auto-iris lens, the supplied clamping core (B) must be installed on the lens wire, to
prevent electromagnetic interference from the other connected devices.
L
C mount type lens
1
2
2
3
CS mount
type lens
L53R2/XE GB 2000, 3, 3
English 7

MOUNTING THE LENS
Rewiring the lens cable in the lens iris plug
1Prepare the lens cable
Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire.
2Install the lens iris plug
Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close
the plug cover.
Pin layout
DC type lenses VIDEO type lenses
1Brake coil (–) + 2 V DC (50 mA max.)
2Brake coil (+) Not used
3Drive coil (+) Video output ( .0 Vp-p, high impedance)
4Drive coil (–) Ground (for video signal and DC power)
Flange-back adjustment
If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of
focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the
flange-back position as described below.
1Using a + screwdriver, loosen the FLANGE BACK LOCK screw (M2:+).
2Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens.
3Set the zoom lens to the maximum wide angle position, set the focus using the FLANGE BACK ADJ screw.
4Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot.
When the setting is complete, tighten the FLANGE BACK LOCK screw.
1
2
43
1
43
1
22
2
1
4
LOCK
3
ADJ.
L53R2/XE GB 2000, 3, 3
8 English

CONNECTIONS
Basic connection for monitoring or recording
The peripheral devices (VCR, monitor, lens, etc ) and cables are
sold separately
1Using a coaxial cable (twin type, 75 ohms), connect the Y/C
OUT connector from the camera to the S-VIDEO input
terminal on the monitor or time lapse VCR
NOTE: When using devices with an S-VIDEO connector, the
supplied clamping core (C) must be installed on the
S-VIDEO cable, to prevent electromagnetic interference
from the other connected devices.
2Power supply choices
•Use a commercially available 24 V AC adaptor. Make sure to
use a cable with an earth line (22AWG or more) to connect to
the earth connector. (Fig 1 )
•When using a DC 2 V power supply, make the connections as
indicated in Fig 2.
CAUTION:
To prevent camera and/or power supply failure, pay close
attention to polarity when making the connections.
3Insert the plug of this power supply into a wall outlet
The POWER indicator (A) will light. Adjust the picture on the
monitor using the Brightness and Contrast controls.
CAUTION:
•Please use a monitor with a Y/C or S-VIDEO input terminal, or a
time lapse VCR with a S-VIDEO input terminal.
•Use a Mini-DIN (round type, 4-pin) plug to connect to the Y/C
connector.
Never use a coaxial cable longer that 0 metres to connect the
camera to the S-VIDEO input terminal.
(Video signal connections)
: VIDEO IN
: VIDEO OUT (A) AC 24 V connection DC 12 V connection
GND AC24V GND
DC12V
Fig. 1 Fig. 2
+–
+
DC12V
–
22
1
L53R2/XE GB 2000, 3, 3
English 9

CONNECTIONS
Coaxial cable type and maximum length
•Cable type RG-59U (3C-2V), 250 m maximum.
•Cable type RG-6U (5C-2V), 500 m maximum.
•Cable type RG- U (7C-2V), 600 m maximum.
CAUTION:
•The RG-59U type cable should not be run through electrical
conduits or through the air.
•Use CCTV/Video-grade coaxial cable.
About the Alarm output terminal
Connect this unit to a VCR or a multiplexer.
Alarm output
A: Alarm signal output
C: Common
CAUTION:
•The digital processing of the settings may disturb the image for
a few seconds after the camera is turned on.
•While the menus are being set, noise sent on the lines by
peripheral devices may cause the settings to change. In such a
case, turn the power off then on again.
Camera control unit connections
This camera main MENU can be set remotely using a camera control
unit (VAC-60, sold separately) connected between the camera and its
peripheral devices (such as a multiplexer, a timelapse VCR, a monitor
TV, etc.).
For detailed information, please refer to the camera control unit
instructions.
NOTE: When finished using the camera control unit, first turn it off,
then disconnect the connecting cables.
Alarm active
About 500 msec.
5 V
CAMERA IN
terminal
Timelapse VCR
Monitor
VAC-60
CAMERA IN
terminal
VIDEO OUT
terminal
L53R2/XE GB 2000, 3, 3
10 English

CONNECTIONS
Before making any connection, make sure all the peripheral devices
are turned off.
Multiple units are connected in series using twisted-pair cables (bridge
connection). To set the addresses and make other fine adjustments,
please refer to page 56.
RS-485 terminal connections
Connect a shielded twisted-pair cable (AWG22) from signal A to
signal A, and from signal B to signal B of the RS485 control terminal
of each of the devices.
•Connection to a VCR
Make the connection between the RS485 (A, B, G) terminal on this
unit and the VCR RS485 A and B terminals and the C terminal.
•Connection to a multiplexer
Make the connection between the RS485 (A, B, G) terminal on this
unit and the multiplexer control terminals (A, B, C).
NOTE: When using devices with an RS-485 connector, the supplied
clamping cores (A) must be installed on the three transmission
cables, to prevent electromagnetic interference from the
other connected devices.
Monitor
Timelapse VCR
CAMERA IN
terminal
RS485
control
terminal
System controller
Multiplexer
12345678910111213141516C
9 10111213141516
CABC AL C R1 R2 C SW C
VCR
12AB
RS485
MONITOR
IN OUT
ALARM IN
CONTROL
SENSOR ALARM
OUT
12V DC IN
POWER
ON
RS485 GND
A
B
B
G
A
B
ALARM input
terminal
Shielded twisted-pair cable
To A signal
To B signal
Ground
GBA
Push in to insert cable
L53R2/XE GB 2000, 3, 3
English 11

USING THE MENU SCREEN
This unit is set at the factory so that it can be used with a DC type auto-iris lens (sold separately).
Therefore, under normal conditions, additional settings or adjustments are not necessary.
Depending on the conditions of use, if settings or adjustments are required they can be done
from the “MAIN MENU” setting screen.
1Press the SET button for about 3 seconds
The MAIN MENU screen will be displayed.
2Using the CURSOR button
1Press the CURSOR (l) button to move the cursor down. When the cursor reaches the
bottom of the screen, it goes back up to the top of the screen.
2Press the CURSOR (j) button to move the cursor up. When the cursor reaches the top
of the screen, it goes back down to the bottom of the screen.
3Press the CURSOR (c) button to move the cursor to the right. This button is also used
to change ON/OFF settings etc.
4Press the CURSOR (d) button to move the cursor to the left. This button is also used to
change ON/OFF settings etc.
Switching to sub-menu screens
Press the CURSOR (j, l, d or c) button until an item with a “c” next to it is flashing,
then press the SET button.
Switching to the MAIN MENU screen
Press the CURSOR (j or l) button to select BACK (it will flash), then press the SET button.
3When finished:
Press the CURSOR (l) button to select END (it will flash), then press the SET button. The
display will return to the normal monitor screen.
MAIN MENU
LANGUAGE SET p
CAMERA ID OFF
SYNC INT
IRIS AI p
WHITE BALANCE ATW p
SHUTTER OFF
MOTION OFF
OPTION SET p
MENU END
LANGUAGE
LANGUAGE ENGLISH
LANGUE FRENCH
SPRACHE GERMANY
(Example)
SET
SET
CURSOR
2
43
1
CURSOR
(Default setting)
MENU BACK
CURSOR SET
MENU END
CURSOR SET
L53R2/XE GB 2000, 3, 3
12 English

USING THE MENU SCREEN
Notes concerning the menu settings
•Modes that cannot be used together
A) The IRIS item SENSE UP setting (other than OFF) and the MOTION item ON setting
B) The SHUTTER item LONG setting and the MOTION item ON setting
•When the IRIS item SENSE UP is used (setting other than OFF), the SHUTTER SPEED cannot be set. (Set either one to OFF in order to use the
other one.)
•If the SHUTTER item is set to LONG or SHORT and the IRIS AI or EI mode SENSE UP setting is used (setting other than OFF), the SHUTTER
item setting will be forced to OFF.
•The SHUTTER SPEED cannot be set if the IRIS item is set to EI mode. Switch the IRIS item setting to AI mode.
•When the OPTION MENU screen ZOOM or MIRROR items are being used, the following items setting screens will not be zoomed in or
mirrored.
☞The BLC setting screen
☞The ADJUSTMENT FOR MOTION screen SIZE and MASKING setting screens
☞The WHITE BALANCE item ATW MASKING screen
•If the OPTION MENU screen AGC item is set to OFF and the IRIS mode SENSE UP setting is used (setting other than OFF), the AGC item
setting will be forced to ON.
MAIN MENU
LANGUAGE SET p
CAMERA ID OFF
SYNC INT
IRIS AI p
WHITE BALANCE ATW p
SHUTTER OFF
MOTION ON
MAIN MENU
LANGUAGE SET p
CAMERA ID OFF
SYNC INT
IRIS AI p
WHITE BALANCE ATW p
SHUTTER OFF
MOTION ON
MAIN MENU
LANGUAGE SET p
CAMERA ID OFF
SYNC INT
IRIS AI p
WHITE BALANCE ATW p
SHUTTER LONG
ADJUSTMENT FOR AI
LENS TYPE DC
BLC OFF
SENSE UP X2
(X) (X)
L53R2/XE GB 2000, 3, 3
English 13

USING THE MENU SCREEN LANGUAGE
LANGUAGE setting
1Press the SET button for about 3 seconds
The MAIN MENU screen will be displayed.
2Press the CURSOR (j or l) button until “SET” in the LANGUAGE item is selected,
then press the SET button
The LANGUAGE screen will be displayed. The initial setting is English, but French and
Germany can also be selected.
3Select the desired language, then press the SET button
The screen displays will change to the language selected.
4When finished:
Press the CURSOR (l) button to select BACK (it will flash) at the bottom
of the screen. Then press the CURSOR (d or c) button to change BACK
to END, and press the SET button.
MAIN MENU
LANGUAGE SET p
CAMERA ID OFF
SYNC INT
LANGUAGE
LANGUAGE ENGLISH
LANGUE FRENCH
SPRACHE GERMANY
SET
SET
CURSOR
LANGUE
LANGUAGE ANGLAIS
LANGUE FRANCAIS
SPRACHE ALLEMAND
SPRACHE
LANGUAGE ENGLISCH
LANGUE FRANZ
SPRACHE DEUTSCH
CURSOR SET
MENU BACK
MENU END
L53R2/XE GB 2000, 3, 3
14 English

USING THE MENU SCREEN CAMERA ID
CAMERA ID setting
1Press the SET button for about 3 seconds
The MAIN MENU screen will be displayed.
2Press the CURSOR (l, then d or c) button to change the CAMERA ID setting to
“ON”, then press the SET button
The CAMERA ID SETTING screen will be displayed.
3Example: To set the camera ID to “BN1”
The characters which have been selected will be displayed in the CAMERA ID IS
“????????” section.
1Press the CURSOR (c) button until “B” is flashing, then press the SET button.
2Press the CURSOR (l or d) button until “N” is flashing, then press the SET button.
3Press the CURSOR (l or c) button until “1” is flashing, then press the SET button.
☞Determining the start position for character input
Press the CURSOR (l) button until 2 is flashing, then press the CURSOR (d or c) button
until the 2 is pointing to the start position. Select the characters using the CURSOR buttons.
☞Changing the camera ID to a new ID
Press the CURSOR (l, then d or c) button to change the PRESET setting to ON, then
press the SET button.
MAIN MENU
LANGUAGE SET p
CAMERA ID ON p
SYNC INT
CAMERA ID SETTING
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
123456789 :-
CAMERA ID IS ????????
CURSOR SET
CURSOR SET
SET
CAMERA ID IS BN1?????
CURSOR SET
CAMERA ID IS ????????
PRESET ON
OFF
CURSOR SET
L53R2/XE GB 2000, 3, 3
English 15

USING THE MENU SCREEN CAMERA ID
4Press the CURSOR (l) button to select “SET” as the POSITION setting (the setting
will flash), then press the SET button
The CAMERA ID SETTING screen will be displayed, and the set camera ID will flash at the
position currently set.
5Press the CURSOR (d, c, j or l) button to determine the display position, then
press the SET button
The display will return to the CAMERA ID SETTING screen.
NOTE: If the CAMERA ID is reset (using the menu PRESET setting), its position will also be
reset to the default position (right bottom corner).
6When finished:
Press the CURSOR (l) button to select BACK (it will flash) at the bottom of the screen.
Then press the CURSOR (d or c) button to change BACK to END, and press the SET
button.
☞To return to the previous screen, select BACK then press the SET button
CAMERA ID SETTING
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
123456789 :-
CAMERA ID IS BN1?????
POSITION SET p
CURSOR SET
CURSOR SET
BN1
MENU BACK
CURSOR SET
MENU END
SET
L53R2/XE GB 2000, 3, 3
16 English

USING THE MENU SCREEN SYNC/INT
SYNC settings
The following three types of synchronization settings can be carried
out.
AInternal synchronization (INT)
Generates a sync signal for internal camera use.
BPower supply synchronization (L - L: line-lock)
Matches the vertical sync signal for the camera with the
frequency of the AC power supply.
CExternal sync (VBS)
Matches the camera’s sync signal with the sync signal from an
external source.
AInternal synchronization setting (INT)
1Press the SET button for about 3 seconds
The MAIN MENU screen will be displayed.
2Press the CURSOR (l, then d or c) button to change the
SYNC setting to “INT” (the setting will flash)
3When finished:
Press the CURSOR (l) button until END is flashing at the bottom
of the screen, then press the SET button.
The display will return to the monitor screen.
MAIN MENU
LANGUAGE SET p
CAMERA ID OFF
SYNC INT
SET
SET
CURSOR
MENU END
L53R2/XE GB 2000, 3, 3
English 17

USING THE MENU SCREEN SYNC/L-L
BPower supply synchronization setting (L - L)
When using a camera switcher to connect 2 cameras or more to one monitor, there may be a
vertical roll of the images when switched. In such a case, set as described below.
1Press the CURSOR (l, then d or c) button to change the SYNC setting to “L - L”
(the setting will flash), then press the SET button
The ADJUSTMENT FOR L - L screen will be displayed.
2Switch the display on the monitor from camera 1 to camera 2
Press the CURSOR (d or c) button to adjust the vertical sync phase
☞Returning the value to the default setting
Press the CURSOR (l, then d or c) button to change the PRESET setting to ON, then
press the SET button.
3When finished:
Press the CURSOR (l) button to select BACK (it will flash) at the bottom of the screen.
Then press the CURSOR (d or c) button to change BACK to END, and press the SET
button.
☞To return to the previous screen, select BACK then press the SET button
Note: Power supply synchronization setting is not possible when a 2 V DC power supply is
being used.
PRESET ON
OFF
CURSOR SET
MAIN MENU
LANGUAGE SET p
CAMERA ID OFF
SYNC L-L p
SET
CURSOR
ADJUSTMENT FOR L-L
[V SYNC PHASE]
í--ú---z------ü 11
CURSOR
MENU BACK
CURSOR SET
MENU END
L53R2/XE GB 2000, 3, 3
18 English

USING THE MENU SCREEN SYNC/VBS
CExternal sync setting (VBS)
1Connect the output signal from the other camera to the external sync input
connector of this camera
The SYNC setting in the MAIN MENU screen will change to VBS.
2Press the CURSOR (l) button to select the SYNC setting “VBS” (the setting will
flash), then press the SET button
The ADJUSTMENT FOR VBS screen will be displayed.
3The H (horizontal) value will flash Press the CURSOR (d or c) button to adjust the
horizontal sync phase
Note: If not using a camera (for the output signal), use a sync signal generator.
4Press the CURSOR (l) button until the SC1 (sub-carrier) value is flashing, then press
the SET button to select the color phase (SC1 to SC4)
5Press the CURSOR (d or c) button to make fine adjustments to the color phase
☞Returning the value to the default setting
Press the CURSOR (l, then d or c) button to change the PRESET setting to ON, then
press the SET button.
MAIN MENU
LANGUAGE SET p
CAMERA ID OFF
SYNC VBS p
ADJUSTMENT FOR VBS
[PHASE]
H íú-----z------ü 3
SET
CURSOR
SC1 ú------z------ü 1
SC1 ➞SC2 ➞SC3 ➞SC4
L53R2/XE GB 2000, 3, 3
English 19