Sanyo CAP3310TXN User manual

Instruction
Manual Colour
Television
STEREO*
SURROUND (ALL IN ONE:
TELETEXT
S7ERMINAL
VIDEO MULTI TERMINAL
(PAL/NTsc/NTsc4.43)
MESSAGE
CALENDAR
HELP MESSAGE K
Model CAP3310TXN
CZP3310TX
*Model CAP331 OTXN –NICAM Digital Stereo Decoder and West Germany Stereo Decoder built in.
*Model CZP331 OTX –NICAM Digital Stereo Decoder built in.

Introduction
HHi-Fistereosoundcircuitwith %r-
round Circuit.
ALL IN ONE (Surround speaker built in).
It’s easy to enjoy TV and video sound with the Surround
effect,
SurroundSystem
The sounds that we hear in anatural listening
environment consist of those which reach
our ears directly from the sound source, and
those which reach us indirectly after being
reflected off of the floor, walls, and other sur-
rounding objects. The Surround System elec-
trically produces these direct and indirect
sounds, then sends them through speakers to
surround the listener with sound that isrich in
stereo presence.
Where to Place the TV for the best Surround Effect
●Do not place furniture or other objects any closer than 30 cm
from the sides of the TV. Placing objects directly next to the
sides of the TV will block the sound from the speakers.
●It is agood idea to place the TV in acorner of the room. This
allows the walls to serve as reflectors to achieve agreater
Surround effect.
9This Av Television Allows Free System
Expansion
●S-terminal is provided.
.Three videolaudio inputs and one audio output enable easy
VCR connection for tape playback and editing.
■MESSAGE, CALENDAR and HELP-
MESSAGE functions
In additional to standard TV functions, this set offers
the convenience of MESSAGE, CALENDAR and HELP
MESSAGE functions in 5language: English, German,
French, Italian and Spanish.
Electric Mains
The TV receiver is manufactured to utilize an AC VOLTAGE
SOURCE of 220-240 Volts, 50Hz.
Safety Precaution
When the TV receiver is not to be used for an extended period
of time, it is advisable to disconnect the AC power cord from
the AC outlet.
WARNING
To prevent fire or shock hazard, do not expose the unit to rain
or moisture.
High voltages are used in the operation of this TV set.
Do not remove the back from your set. Refer servicing to quali-
fied service personnel.
e
Aerial Connection
●Connect the cable with aplug from aUHF (or VHF) aerial to
the Ir aerial socket on the cabinet back.
-———-
-———-
_—— —=
—-—=
I(3I Ir+
~raerialsocket
.For all aerial circuit problems please consult your local deale-
U
Battery Installation (Remote Control Transmitter)
❑Remove the battery cover by sliding.
❑Install two “M” 1.5 volt batteries so that the “+“ and “-”
marks on the batteries match the”+” and” –” marks inside
the unit.
❑Close the battery cover.
Note: Replace the batteries when the TV set is showing the fol-
lowing symptoms:
Operation is unsteady or erratic, sometimes the TV set
does not work with transmitter. Discharged batteries
may leak and damage the unit. The normal life of batter-
ies should be from nine to ten months.
xFor the handling of these functions, please refer to
the separate operating manual.
–l–

Controls \f’ >
/
bSurround Speaker
/
/
@Main Speaker
>b
\
‘~< J“~
Press to open
/i
~Mam ON/OFF Switch
Remote Control Detector
Standby and Power Indicator
>
[of.,,,..,. .,,-,,. m~ON/OFF (I
Operation of the Receiver
‘witching on/off ●AUTO SHUTOFF
__BTo turn on the TV: This TV set incorporates the AUTO SHUT OFF function.
Press Mains ON/OFFswitch ~. Even if the TV is left on afteryou have gone to sleep,the
TV set changesto the standby mode within 10 minutes
●To turn offtheTV:
Press the Power ON/OFF button ~on the remote control afterallbroadcastshaveended.
transmitter, and the TV changes to the standby mode. During Note: AUTO SHUT OFF also functions for the AV mode even
the standby mode, the standby and power indicator illumi- when there is no signal being transmitted.
nates more brightly than during the power–ON mode. The remaining time for AUTO SHUT OFF is displayed on
Press this button ~to turn off the unit for short periods the screen.
of the time.
.Toturn on the TV from the standby mode:
Press one of these button.
I
Power ON/OFF (Q
(Remote control transmitter) Remaining time
L
au 1
Programme Selector ~‘10 AUTO PAUNTSC
(Remote control transmitter)
Volume @Programme selection
●TOcutoffthe mainspower completely: Press the right side (+)of the programme selector ~of the
Press the Mains ON/OFF switch ~. TV set, and the TV set will step up to the next station, i.e; 1, 2,
3...29, VCR1, VCR2, VCR3, 1,2,3 ...
Important! Be sure to set the Mains ON/OFF switch ~to the Press the left side (–), and the TV set will step down to the
off position, if the power failure occurs while view- previous station.
ing. –2–

(Operation of the Receiver)
Sound adjustments
●To adjust the sound volume:
Press +or– volume @button.
I
IASOUND
E9s Is GIBE------- 1
.Toadjust the bass, treble, balance and the depth of surround
effect:
Select the control function by pressing SOUND SELECT Q
button.
cEach time SOUND SELECT~ button is pressed, the con-
trol function changes as follows:
9: BASS
-------- +----t---
BAss
Icl”
~TREBLE
-------- +-- t-----
TREBLE
uBALANCE
-------- t--------
BALANCE
J
~
-SOUNO SURROUNDLEVEL
mllluallm------- ----mw((((u(----
1 1 L1
SOUND VOLUME SURROUND
LEVEL
Note: “SURROUND LEVEL’ will be skipped when the Sur-
@.... TV/VIDEO Selector
To watch the television programmed leave this switch in the
TV mode. When this switch is set to the VIDEO mode you can
enjoy the playback from the VCR or other AV equipment con-
nected to the AV input terminals.
Each time the TV/VIDEO Selector ~is pressed, the AV posi-
tion changes as follows:
t
l--.%LL&d&
TV mode ~
I
@.... Memory O
This function lets you store the settings (for colour, bright-
ness, contrast, video tone, tint, sound volume, bass, treble,
balance and Surround effect) in memory for both picture ar
the sound. Simply adjust the picture and sound as desiredY
then press the Memory 0@button. To recall these levels
from memory, press the Normalization ~0~ @button on
the remote control unit.
When Memory button
is pressed, “NORMAL’
is displayed,
INORMAL
.-- *+--- I
II
round effect is turned off. 0.... Headphone Jack ~
Insert the headphones plug into this jack to listen to either
Adjust the bass, treble, balance or the depth of surround ef-stereo or monaural sound via aheadphones set.
feet by pressing Volume @button. Note: No sound will be heard from the speakers when the
headphones plug is connected to this jack.
Pictureadjustments
elect the picture control function by pressing PICTURE
ELECT @button.
Each time PICTURE SELECT @button is pressed, the
control function changes as follows:
@COLOUR
mmalmlmlm-------
COLOUR
‘~ BRIGHT
mllllm DmDB------
BRIGHTNESS
J-L
‘INE TUNING VIDEO TONE
I(1 CONTRAST
●lBamllmm -------
1CONTRAST
1
cl
K-x TINT
-------- t--+-----
TINT
OTE: “TINT” will be skipped during PAL mode.
❑Adjust the colour intensity, brightness, contrast, tint, video
tone or fine tuning by pressing Volume @button.
–3–

Remote Control Operation
~Programme Selector
@Colour System Selector
(AV mode only)
@Normahzizfou: \
Brightness
-Contrast
Video tone
TINT ~
(for NTSC and NTSC 4.43)
Note: This button has no
effect during PAL mode.
~1 _TVIVCR switch
/●For operation of the TV set,
set the TV/VCR switch to
“TV position.
Programme up (Press this button, and the programme
position step up to the next position.)
Programme down (Press this button, and the programme
position steps down to the previous position.)
~l%wer ON/OFF
@Off timer
~TV/VIDEO Selector
cI
II @Channel Scanning
‘1
@Recall
@Sound mute
0Volume
~AUDIO SELECT
Fine tuning
@Bilingual A/B
@Stereo/Mono
@Surround ON/OFF
Main ON/OFF switch of the TV set must be in “ON” position Picture adjustments
before remote control operation is possible.
Point transmitter towards the TV set, then press the appropri- .To adjust the colour intensi~:
ate function button for the following controls. Press @(Colour) button.
+
‘m .... Power ON/OFF (!) Press Aor ~volume @button.
Press this button to switch TV set on.
To switch TV set off, press again. .TO adjust the brightness:
~.... Programme selection
●e.g. TO select programme number 17, press “l-” button and
then press “7” button ~within five seconds.
To select programme number 27, press “2-” button and
then press “7” button ~within five seconds.
■You can select any desired programme number directly
from standby mode.
.e.g. To directly select programme number 2from stand-
by mode, press the “2” button. The set is then
switched on, and the picture of programme number
2appears.
Todirectly select programme number 16 from stand-
by mode, press the “l-” button (after which the
Standby and Power indicator flashes), then press the
“6” button. The set isthen switched on, and the pic-
ture of programme number 16 appears.
Press @(Brightness) button.
Press Aor ~volume button.
●To adjust the picture contrast:
Press O(Contrast) button.
Press Aor ~volume button.
●TO adjust the video tone:
Press V. TON. button.
1
Press Avolume button.
-whap picture.
Press Vvolume button.
~soft picture.
–4–
El
QCOLOUR
nls Io*9nn -------
D
‘t BRIGHT
tmmaomnlnn------
❑
C) CONTRAST
slnnsooss-------
n
V.TON.
-.-.----+--,.----

(Remote Control Operation)
●Fine tuning
Press <> (Fine tuning) button.
+
Press Aor ~volume button. ❑
<>
Note: Normally fine tuning is not required for this TV. However,
in some case (such as radio interference) picture may be-
come more clear by detuning from the best tuned fre-
quency.
In such case, you can use this fine tuning to eliminate
some interference beat pattern.
Sound adjustments
●TO adjust the sound volume:
Press A(up) or ~(down)
volume ~button.
n~SOUND
m#mflnmlmm-------
●Toadjust the bass, treble, balance and the depth of surround
effeet:
Select the control function by pressing AUDIO SELECT o
button.
.Each time AUDIO SELECT obutton is pressed, the con-
trol function changes as follows;
El
-j:
BASS
-------- +----l---
BASS
tEl
~TREBLE
-. .....- +--l -----
TREBLE -El
uBALANCE
-------- +--------
BALANCE
1
SOUND VOLUME SURROUND
LEVEL
Note: “SURROUND LEVEL’ will be skipped when the sur-
round effet is turned off.
Adjust the bass, treble, balance or the depth of surround ef-
fect by pressing Volume obutton.
@... SurroundON/OFF
To enjoy the surround effect, press the Surround ON/OFF@
button.
To cancel the effect, press this button again.
Surround OFF
STEREO
b~
Surround ON
STEREO
~ww(
@... Stereo/Mono ~
●When receiving the stereo broadcast, is displayed.
If the sound of astereo broadcast is not clear due to interfer-
ence or poor reception, select the MONO position by press-
ing this button.
.In the AV mode, select either STEREO or MONO to match
the stereo or monaural condition of the audio signal coming
from an external source, e.g. aVCR, A. V. equipment, or
other component by pressing Stereo/Mono Switch.
@... BilingualA/B
When receiving the bilingual broadcast, ‘A~H’A) is die_
played.
You can select the main or sub language with this button.
MAIN (A)
w
In the AV mode, each time Bilingual AIB button is pressed, the
audio channel changes as follows:
LEFT (A)~RIGHT (B)
@.... Sound mute ~
Should you wish to mute the
sound (e.g. While talking on the
telephone), press this button once.
To switch the sound back on,
press it again.
@... Normalization+*+
Press this button to recall the pic-
ture and sound settings which
you stored using the Memory O
@button. ❑
NORMAL
.-- ++---
@.... ChannelScanning~J
Press Channel Scanning button @to search for aprogramme.
The channel positions are automatically scanned, and the chan-
nel scanning will stop at the position where it began. To stop at
the position you want, press this button again.
=+=-------------*D
b-m-m-b
–5–

(Remote Control Operation)
~.... Offtimer Q
After aset time has elapsed, the power of the TV receiver is
switched off automatically.
●Each time Off timer button @is pressed, the set time
changes as follows:
~~~
L-J”L14U
t30minutes 60 minutes
4
●
●
+
-120 -90
120 minutes 90 minutes
With the off timer being set and the chann~l .A!wmlayreset, the
srem’alning time is displawd by pressing the off timer button
ayalli.
When the button is pressed again within three secoria<-u?her
the button was first pressed in above manner, the time is set
to an upper time which is most close to the remaining time.
Just one minute before switching off, “-01” and program me
number you are watching are displayed on the screen.
The timer setting will be cancelled if the power is switched
@).... Recall ~/S
To display the on-screen indications, press this button.
The display disappears after five seconds.
L___l’
STEREO
wProgramme
number
9
.
Note: When this button is pressed for more than 2seconds,
The following is displayed and the unit enters SELF
DEMO mode. This mode is for use in storefront demon-
strations.
It has no effect on TV operation.
SELF DEMO. SELF DEMO. mode
kE-E!!l
●To cancel the SELF DEMO mode, press the Recall ~/S@
button once again.
●If the Memory O0button is pressed in the SELF DEMO
mode, the self-demonstration will begin. Youcan also cancel
the SELF DEMO mode midway through play by pressing the
Recall ~/S ~button.
–6–
VCR USE
Note: This remote control transmitter has been designed es-
pecially to be used in conjunction with selected SANYO
VCR’S.
Some SANYO VCR’s may have their own functions, so
please refer to the individual instruction booklet when
using this remote control with SANYO VCR’s to ensure
compatibility.
●For VCR use set the TVAfCR switch to “VCR” position.
REWIND/—
REVIEW
RECORD —
L4
POWER ON/OFF BUTTON
Use to turn VCR power on and off.
PLAYBUITON
Use to playback the tape.
STOP BUITON
Use to stop the movement of the tape.
FAST/CUE
—TVIVCR SWITCH
—CHANNEL UP
—CHANNEL DOWN
—POWER ON/OFF
—PLAY
—FAST/CUE
—PAUSE/STILL
—STOP
Use to advance the tape at fast speed, or in order to playback
the tape at fast speed.
REWIND/REVIEW
Use to rewind the tape, or in order to playback the tape in
reverse at fast speed.
PAUSEKTILL
Useto temporarily stop (Pause) the tape when recording, or in
order to see a still image during playback.
CH UP DOWN A/~
Use to change the programming position for the VCR.
RECORD
Use to record on the tape. Press both of the RECORD buttons
at the same time.

Pre-Settinu Of Stations UPt032 broadcaststations inyo.rreception area can b,~tO~ed inthe electronic memOI-Y.
There are two ways of presetting as follows:
Automatic presetting –the basic way
All receivable channels are automatically tuned in and memo-
rized in consecutive program positions.
Note: Programme position 1to 29 can be automatically
preset. VCRI, VCR2 and VCR3 positions cannot be au-
tomatically preset.
Manual presetting
Use to preset areceivable channel in any desired program po-
sition, e.g. the position with the same number as the channel.
Automaticpresetting
1.Select any programme position from 1to 29.
(Automatic presetting is
VCR2, or VCR3 position.)
2. Press PRESET obutton.
m
m
$mp ,:“”,+ z8
BUD.,”0
not possible from the W%?,
K
AUTO
Program PRESET
position
&
Channel band
VL: low VHF band
VH: high VHF band
3. Press TUNING (+)@ button. U: UHF band
mQ4’
I\J
The channels are preset in consecutive postions beginning
from the program position “l”.
After all available channels (position 1to 29) have been
preset, the unit returns to the postion “l”.
Note: To cancel automatic presetting midway, press the
Recall D/S@ button.
IManual presetting]
1.Press PRESET obutton.
1r1
w
ml
p+p,;“”,@p“i%o
2. Press PRESET@ button again.
w
$p-%%SUM MEW
3. Press the programme selector
~or ~to select the desired
programme position.
AUTO
PRESET
1VL
Mmm-------------
El
1VL
now------------
\0
6VL
MmB-------------
4. Press 8AND selector @to select
the channel band.
m
p’ -?*”8
,5fT 7“.1.. a!4,.0
--.-.-.---.-.-.-
When BAND selector is pressed, the frequency will be set to
the lowest frequency in the set band.
.Channels band VL, VH and Uare for the following channel
groups. (Asia) (New Zealand)
VHF low band :E2– E4 1–3
VHF high band :E5 –E12 4–11
UHF band :21 – 69 21 – 69
(–) button until the desifed SPIC. , , ...’_
tion appe.w?-. ‘““
m
u
6VH
tmamEm----------
6’-%58
xFn,sE, ..,. .,”O .,.0 The number of upright segments
increases for ahigher-frequency
channel.
6. Press o(Memory) button e. 1-l
6VH
Bn#nmm----------
7. Repeat steps 3to 6for other desired channels.
8. Press PRESET @or ~/S
n
STEREO
(Recall) obutton. P4
This completes the presetting.
Memory- Copy This TV tuning system has
another advanced feature called
“memory copy”.
For example, if you wish to copy the TV channel in the
programme position “2” into the programme position “6”:
1. Select the programme position “2”.
2. Press PRESET@ button.
3. Press PRESET@ button once again.
4. Press “6” button of the programme selector ~.
5. Press O(Memory) button 0.
6. Press PRESET@ or Q/S (Recall) button e.
–7–

(Pre-Setiing of Stations)
IInsertingChannels
The following example shows how to insert Channel-D of
programme position “4” into programme position “2”.
TDeletingChannels I
The following example shows how to delete Channel-B from
programme position “2”.
Channel-A
n1
I
Channel-D
Insert
(
u
Channel-B Channel-C Channel-D
-D 4
I
\Programme 1
hPosition I
I
IVCR3 I
I
,II
I
a-m----------’;
1.
2.
3.
4.
5.
6.
Select programme position “4” (Channel-D).
Press PRESET @button.
Press PRESET @button once again.
Press “2” button of the Programme Selector ~.
❑-m
Press and hold down the TVAIIDEO selector o, then press
the (+)Programme Selector o.
Press the PRESET ~or Recall ~/S ~button.
.Channel-D of programme position “4” is now inserted into
programme position “2”.
.In this example, the channels from Channel-B (programme
position “2”) onward will be shifted successively into the
next highest programme position.
-----
Channel-A ~Channel-D IChannel-B Channel-C
Ll+n:rrl-rl
I----- Chan~el-D
El
VCR3
IEl5
I
I
I
LHJJ-----------’
Note: You cannot insert achannel which would cause the
channel in programme position “29” to shift to ahigher
programme position. You also cannot insert channels
into the VCRI, VCR2, or VCR3 position. When the
Channel-A
D1
I
r__ —-- -
IChannel-B ;
II
I
7
Q
+
I21
‘-7--DELETE
Channel-C
El3
Programme
Position
Channel-D
-D 4
I
I
I
I
L-!!!4 I
I
b-m-----------
1.
2.
3.
4.
5.
Select programme position “2” (Channel-B).
Press PRESET ~button.
Press PRESET @button once again.
El
2VL
lmn-------------
Press and hold down the TVIVIDEO selector e, then press
the (–)Programme Selector o.
Press PRESET @or ~/S (Recall) ~button.
●Channel-B of programme position “2” is now deleted.
●In this example, the channels from Channei-B
(programne position “2”) onward will be shifted Suc-
cessively into the next lowest programme position.
Channel-A Channel-C Channel-D
~~1
I1l–l 21–I 31----’,:
II
II
I
IVCR3 I
I
LII
h-m-----------
Note: Channel deletion is not possible in the VCRI, VCR2, or
VCR3 position.
When the above procedure is done, the position indica-
tor (VCRI, VCR2, or VCR3) will flash in red.
above procedure is done, the position indicators will
flash in red.
–8–

TELETEXTUSE ●Automatically adjust fordisplays in English, German, French, Swedish, ltalian and
Spanish in accordance with the television broadcast signals.
INDEX ~—
TIME/SUB @—
MODE —
STORE ~1 —
RED ~
Page Selection _
L
■Switching to the Teletext Mode OB~
Press the TV/MIXflEXT button, then the screen changes as
follows:
1I I I 1
SIZE ~
HOLD ~
TVIMIXITEXT (J @ @
PAGE UP A
PAGE DOWN ~
CYAN
YELLOW
GREEN
1]
Back to TV programme.
PageSelection
DIRECTPAGEACCESS
Apage can be selected with the 0-9 buttons. For example, to display page 120 press buttons 1, 2and O. The selected
page number will appear on the screen.
UP-DOWN PAGE ACCESS
If apage is displayed on the screen and you want to read the following page, you can press the UP button instead of
selecting the page number. To bring back the previous page press the Down button. If you keep the UP or DOWN button
pressed the page numbers will run up or down until you release the button.
The page number will change as follows by pressing the UP-DOWN button.
(A) P200 –P201 –P202 –.............– F299 –P200 –P201
(~) P200 –P299 –P298 –.............– P201 –P200 –P299
Note: In the LIST mode, you can access the pages directly. (See page 12.)
–9–