Sargent and Greenleaf Biometric Keypad User manual

Biometric Keypad QuicKStart Guide
➥InstallIng BatterIes
Underneath the bottom of the keypad, you’ll find a raised ridge. Place your finger behind it, pull
slightly forward and down to open the battery compartment.
Snap the connectors onto a pair of fresh Duracell®brand (for best performance) alkaline batteries.
The batteries must be alkaline. Orient the batteries in the tray with the connector wires facing up.
The smaller photo shows proper positioning of the battery cable clip under the cross bar of the
battery drawer. The drawer will slide into the keypad much easier if you position the battery
cable clip as shown. For clarity, the photo shows the drawer removed from the keypad. However,
it is not removable once the keypad is installed on its base.
Once the batteries are in place, push the tray back up into the keypad until it snaps into place.
➥turnIng the lCD BaCklIght OnanD Off
Press the START button located just above the LCD screen. This screen will
appear for about a second, then automatically change to the next screen.
Press the # ▼ button at the bottom of the keypad when this screen appears.
Enter the lock’s 6-digit master code, followed by # when prompted by this screen.
The factory default master code is 1-2-3-4-5-6.
Press 1 to select the Display Setup option. You can press the up or down arrow
key to get to this screen before you press 1, or you may press 1 immediately.
Press 2 to select the LCD Backlight option. You can press the up or down arrow
key to get to this screen before you press 2, or you may press 2 immediately.
To turn the backlight off, you would press 2.
Press 1 to select the Enable option. This turns on the LCD backlight whenever the lock is in use.
Don’t press any more buttons until the display goes blank.
Document 630-729
Revised 12/1/05
Copyright ©2005, Sargent & Greenleaf, Inc.
A Wholly Owned Subsidiary of Stanley Security Solutions, Inc.
www.sargentandgreenleaf.com
Note: This QuickStart Guide is designed to show you how to begin using your Biometric Keypad immediately. There are
many additional features, which can be found in the full operating instruction document. It can be obtained in the Product
Instruction Section, at www.sargentandgreenleaf.com. Use this QuickStart Guide ONLY if
your Biometric Keypad has already been synchronized with the lock according to the
procedure on page 6 of the full operating instructions.

➥ChangIng the Master CODe
Press the START button located just above the LCD screen. This screen will
appear for about a second, then automatically change to the next screen.
Press the # ▼ button at the bottom of the keypad when this screen appears.
Enter the lock’s 6-digit master code, followed by # when prompted by this screen.
The factory default master code is 1-2-3-4-5-6.
Press 3 to select the Master Code option. You can press the up or down arrow
key to get to this screen before you press 3, or you may press 3 immediately.
Enter your new 6-digit master code, followed by #.
Don’t press any more buttons until the display goes blank.
This screen appears while you are entering your new master code.
To confirm, enter your new 6-digit master code again, followed by #
This screen confirms that the new master code has been set. The old master code no longer works.
Press 2 to select the Lock Setup option. You can press the up or down arrow
key to get to this screen before you press 2, or you may press 2 immediately.
➥enrOllIng anD DeletIng the fIrst fIngerprInt
Press the START button located just above the LCD screen. This screen will
appear for about a second, then automatically change to the next screen.
Press the # ▼ button at the bottom of the keypad when this screen appears.
Press 3 to select the Fingerprint Setup option. You can press the up or down arrow
key to get to this screen before you press 3, or you may press 3 immediately.
Press 2 to select Enroll or 3 for Delete. You can press the up or down arrow key to get to the appropriate
screen before you press 2, or you may press the number for your selection immediately.
You will be instructed to place your finger on the keypad
sensor 3 times to create a detailed image. These screens
repeat until the fingerprint has been scanned 3 times.
Enter 1, followed by #.
Enter the lock’s 6-digit master code, followed
by # when prompted by this screen.
To confirm, enter the lock’s 6-digit
master code again, followed by #.
Your fingerprint has been enrolled, and you can
now use it to open the lock, in lieu of a code.
Don’t press any more buttons until the display goes blank.
Press 2 for Enroll. Press 3 for Delete.
Enter 1, followed by #.
Enter 1, followed by #.
Your fingerprint has now been removed,
and will no longer operate the lock.
Don’t press any more buttons until the display goes blank.
enrOll Delete
Sargent & Greenleaf, Inc.
A Wholly Owned Subsidiary of Stanley Security Solutions, Inc.
PO Box 930, Nicholasville, Kentucky 40356 USA
Phone [phone]
Phone [phone]
FAX [phone]
FAX [phone]
www.sargentandgreenleaf.com
Enter the lock’s 6-digit master code, followed by # when prompted by this screen.
The factory default master code is 1-2-3-4-5-6.