Sargent and Greenleaf Quick Mount Keypad Use and care manual

page 1
Installation and Battery Change Instructions
Quick Mount Keypad
for use with S&G 6120, 6123, Titan 2006 and
Spartan™1006 PivotBolt Safe Locks
Copyright©2014, Sargent & Greenleaf, Inc.
Document 630-876
Revised 6/5/2014
Mounting Considerations
• Sargent & Greenleaf Quick Mount Keypads are designed with the same mounting screw locations as most other S&G
locks, both mechanical and electronic, to simplify retrofit.
• Modifications to the keypad are not recommended and will void the product warranty.
• The Quick Mount Keypad will accommodate one 9-volt battery. S&G recommends fresh Duracell®brand batteries.
Do not use old or partially drained batteries.
Sargent & Greenleaf, Inc.
PO Box 930
Nicholasville, KY 40340-0930
Phone: [phone] Fax: [phone]
Phone: [phone] Fax: [phone]
Sargent & Greenleaf S.A.
9, Chemin du Croset
1024 Ecublens, Switzerland
Phone: [phone]
Fax: [phone]
Attaching Screws: Use only the screws provided with the keypad. Mounting screws will be either 8-32 or M4, depending on the applica-
tion. They must engage the mounting surface (safe door) by at least four full threads. Do not use thread sealing compounds as these may
weaken the keypad base material.
Recommended Attaching Screw Torque: No more than 15 inch-pounds (1.695 Nm) for the keypad attaching screws.
Minimum Lock Cable (Spindle) Hole Diameter: 0.312"(7,9 mm)
Maximum Lock Cable (Spindle) Hole Diameter: 0.406"(10,3 mm)
Code Restrictions: Personal data that can be related to a code holder, such as a birth date, street number, or phone number, should not
be used in creating a lock code. Avoid codes that can be easily guessed.
Note: Every installation of this product must comply with these requirements and those in the product installation instructions to qualify
for the manufacturer’s warranty and to comply with EN1300 requirements.
LOCK CABLE
RECEPTACLE
SPACE FOR
EXCESS CABLE
MOUNTING STUD
OPENINGS
BACK OF KEYPAD
Before You Install
Your S&G electronic safe lock should be installed inside the safe door first, following the instructions with which it is
packaged. The lock cable should be extending through the door’s spindle hole to the outside of the safe.
FRONT OF KEYPAD
LIGHT BUTTON
If the version of keypad you are installing includes the light feature, after
battery installation, press this button to illuminate the keypad for ten seconds.

page 2
Step 1
Place the metal collars over the keypad mounting screws.
Then install the screws into the keypad mounting holes in the safe
door. Note that the lock is already installed, and its cable is coming
through the spindle hole.
Step 2
Plug the lock cable into the receptacle in the back of the keypad. Align the
raised ridges of the plug with the offset slots in the receptacle.
Step 3
Coil the excess lock cable into the space provided in the back of the keypad. As you
move the keypad up against the safe door (over the mounting screws you installed
in Step 1), be sure to place any excess cable into the back of the keypad so that no
cable will be pinched between the back of the keypad and the safe door.
Step 4
In order to place the back of the keypad over the mounting screws and flat against
the safe door, you will have to angle the keypad to about an eleven o’clock position,
as shown at the right. Once the keypad is flat against the safe door, pull it down
in the direction indicated by the arrow, until it comes to a positive stop. The
movement will be less than ½ inch.
Watch a short removal/installation video: http://www.sargentandgreenleaf.com/QM
Step 5
Now turn the keypad clockwise a few degrees until it comes to a stop. The columns
of numbers should now be straight up and down. Your installation is complete.
Before closing the safe door, and after installing a battery (as shown below), test
the lock and keypad operation by following the operating instructions for your lock.
Battery Installation / Changing
A sliding door at the bottom of the keypad provides
access to the battery. Slide the door to the left to
open. S&G recommends Duracell®brand 9-volt
alkaline batteries for its locks. Simply snap a battery
onto the connectors, place the battery inside the
keypad, make sure all wires are completely inside
the keypad, and slide the compartment door to the
right until it’s fully closed.