Sartorius Cubis Series User manual

Operating Instructions
Sartorius Cubis Series
Electronic Semimicro, Micro, Precision and Analytical Balances
MSE Models
1000025315

2Cubis MSE Operating Instructions
Contents
Contents
Notes on Using these Instructions � � � � � � � � � � � � � � � � 3
Safety Instructions���������������������������� 4
Intended Use �������������������������������� 6
General View of the Equipment ���������������� 7
Getting Started ������������������������������ 9
Unpacking the Equipment��������������������� 9
Setup Instructions��������������������������� 9
Assembly ��������������������������������� 11
Transporting the Balance ��������������������� 17
Storage and Shipping Conditions���������������� 17
Power Connection��������������������������� 18
Warm-up Time ����������������������������� 19
Anti-theft Locking Device ��������������������� 20
Modification Options ������������������������ 21
Preparing Below-Cell Weighing ����������������� 26
Using the Cable Opening in the
Analytical Balance Draft shield� � � � � � � � � � � � � � � � � � 28
Operation����������������������������������� 29
Display and Control Panel ��������������������� 29
Basic Weighing Function���������������������� 30
Leveling the Balance with the Inclination Sensor ���� 31
Turning the Ionizer On/Off (Optional) ������������ 31
Calibration and Adjustment�������������������� 33
Configuration (Operating Menu) ����������������� 36
Key Functions during Configuration ������������� 36
Menu Navigation Example: Setting the Language ��� 36
Menu Structure (Overview) �������������������� 37
Parameter Settings: Overview ������������������ 38
Application Programs�������������������������� 45
Density Determination������������������������ 45
Counting ��������������������������������� 48
Weighing in Percent ������������������������� 50
Calculation �������������������������������� 52
Animal Weighing/Averaging ������������������� 54
Net-total Formulation������������������������ 56
Totalizing ��������������������������������� 58
Mass Unit Conversion ������������������������ 60
ISO/GLP-compliant Print-out�������������������� 62
Data Interfaces� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 63
Error Codes ��������������������������������� 75
Care and Maintenance
(Packing the Balance for Shipping) �������������� 76
Transporting the Balance ����������������������� 80
Disposal ������������������������������������ 86
Specifications�������������������������������� 87
Dimensions (Balance Drawings) ����������������� 100
Accessories (Options) ������������������������� 108
EC / EU Declaration of Conformity��������������� 110
FCC Supplier’s Declaration of Conformity ��������� 111
CSA Certificate of Compliance������������������ 112
EC Type Approval Certificate ������������������� 115
Plates and Markings�������������������������� 116
hThe enclosed CD-ROM contains the
operating instructions as a PDF file�
To read and print the file, you require
the program Acrobat Reader, which
you can download for free from the
Adobe website (www�adobe�com)�
Software drivers for configuration of
SB interfaces can also be downloaded
from the internet:
http://www�ftdichip�com/FTDrivers�htm
The “installation guides" for these
drivers can be found here:
http://www�ftdichip�com/Documents/
InstallGuides�htm

Cubis MSE Operating Instructions 3
Notes on Using these Instructions
Notes on Using these Instructions
tPlease read these instructions carefully and completely before using the device�
tRead the Safety Instructions carefully�
tThese instructions are part of the product� Keep them in a safe and easily
accessible location�
tIf the instructions should be lost or misplaced, please contact Sartorius
for a replacement or download the latest version from our website:
www�sartorius�com
Symbols and Signs
The following symbols are used in this manual:
Danger of explosion
1Potential danger of physical injury or death
Danger of electrical shock
2Danger of physical injury or death
Warning of potential physical injury,
3Health risk or risk of property damage
hUseful information and tips
Notes on use in legal metrology within the scope of validity of
Council Directive 2014/31/EU for instruments for which the conformity assessment
procedure has been carried out (verified instruments)�
Note regarding device operation
Explanation of Symbols
The following symbols are used in these instructions:
tIndicates a required action
yDescribes what happens after you have performed a particular step
1�, Perform steps in the specified order
2�
– Indicates an item in a list
hTechnical advice/Hotline:
Phone: +49�551�308�4440
Fax: +49�551�308�4449

Safety Instructions
4Cubis MSE Operating Instructions
Safety Instructions
This device complies with European Council Directives as well as international regulations and standards for electrical
equipment, electromagnetic compatibility, and the stipulated safety requirements� Improper use or handling can,
however, result in damage and/or injury�
This device should only be operated by trained personnel�
Operators must read these installation instructions, particularly the safety information, and must be familiar with the
operation of the equipment� The operator is required to supplement these safety precautions as appropriate�
The operating personnel must be provided with the appropriate training�
The requirements pertaining to applicable installation regulations must be followed when using electrical equipment
in systems and environmental conditions with increased safety requirements� Relevant laws, standards, regulations,
guidelines and environmental protection laws valid in your country must be observed�
Always keep the equipment and balance freely accessible�
Any installation work or balance operation that does not conform to the instructions will result in forfeiture of all
claims under the manufacturer's warranty�
Danger of Explosion!
1Do not use this equipment in hazardous areas in which explosive materials are present�
Danger of Electrical Shock!
3If the device is not used in accordance with the instructions, this can affect the product liability for the device�
2Make sure that the voltage rating printed on the AC adapter is identical to your local line voltage� The wall outlet must
have a protective grounding conductor� The operating instructions included with the AC adapter must be followed�
2Do not switch on the equipment if the AC adapter or power cord are damaged� If the balance, the AC adapter or
any of the cables are damaged, disconnect the equipment from the power supply and secure it so that it cannot be
turned on�
2Chemicals (e�g� gases or liquids) that can corrode and damage the inside or outside of the balance, AC adapter, power cable or
peripherals must be kept away from the equipment�
2Do not operate the balance unless the housing and the display are undamaged and the housing is closed so that
inadvertent contact with parts inside the equipment is not possible� Make sure that no liquids penetrate the balance
and do not allow conductive parts to touch the balance�
2Note on Installation:
The operator shall be solely responsible for any modifications to the equipment
and for connecting any cables or equipment not supplied by Sartorius�
Information on operational quality is available upon request from Sartorius�
You should only use peripherals and options supplied by Sartorius�
3Protection Class of the Balance Housing
– Models with a readability of ≥10 mg and 0�1 mg: These models fulfill the requirements of protection class IP54�
The IP protection only applies to the balance housing and not to the AC adapter�
– The IP protection is only guaranteed when the weighing pan is mounted�
–The IP protection is restricted if the data interfaces are used�
Retain the cover cap for the data output� When the data output is not in use, reapply the cover cap to protect it
against vapors, moisture, and dust or dirt�

Safety Instructions
3Note on cable quality:
CE conformity is only guaranteed with well shielded cables�
The shielding braid of the cable must be made of metal with at least 80% coverage and also covered with metal foil
as much as possible�
The shielding on both sides on the full metal or metalized connector casing, as well as on the casing inlet, must be
high-frequency compliant and have a flat design�
3You can only turn off power to the device by pulling the plug or disconnecting the power cord, or by unscrewing the four-
pin plug at the DC supply cable for the balance�
3Only use a lightly-moistened cloth for cleaning� See “Care and Maintenance" for cleaning the device� Do not
compromise the IP protection of the balance�
3Do not open the balance housing� If the seal is broken, this will result in forfeiture of all claims under the
manufacturer’s warranty� The device may only be opened by specialized personnel trained by Sartorius�
3Disconnect the balance from the wall outlet prior to moving the device�
3Avoid condensation damage to the device� When the balance is turned on,
condensation build-up is not possible� If the device is moved from a cool environment to a warm environment, you
must allow the device to acclimatize for approx� 2 hours before connecting to the power supply�
Hazards at the Place of Installation and During Operation
3Avoid generating static electricity and establish potential equalization� A 10 kOhm ground is used when connecting
the balance to the power supply�
Disconnecting the ground conductor is not permitted�
3Models with a separate electronics module (e�g� MSE6�6/3�6/2�7 225S/P and 125P): Do not replace the electronics
module�
Replacing with, e�g� models of the ME/SE series will damage the device�
3Exercise caution to avoid glass breakage�
There is a danger of lacerations or cuts caused by sharp edges on glass or metal (contact springs), particularly when
removing or replacing the glass draft shield panels; during cleaning; if a glass sample container breaks, or when
modifying the balance hardware configuration�
3Make sure all equipment operators have received proper instructions when working with hazardous or toxic materials�
Failure to follow correct handling procedures can result in breakage of parts or spillage of liquids or other substances�
Make sure the necessary protective clothing or equipment is worn, such as protective gloves, clothing, eyewear� All safety
regulations applicable in the laboratory must be observed�
3Exercise caution to avoid squeezing or crushing fingers when
– Operating the electronic draft shield
– Removing or installing the panels
– Adjusting the display
3Do not expose the device to aggressive chemical vapors or to unnecessarily extreme temperatures, moisture, shocks,
or vibration�
3The device should be setup in areas away from equipment or devices that have strong magnetic properties�
Extreme electromagnetic fields from electrical lines should also be avoided�
Cubis MSE Operating Instructions 5

Safety Instructions
6Cubis MSE Operating Instructions
Intended Use
Cubis models are high-resolution balances� They were specially
developed for exact determination of material mass in liquid,
paste, powder or solid form�
Appropriate containers must be used for each type of sample
material�
Specific models cover specific weighing ranges: see
“Specifications�"
Cubis models are designed specially for use in research,
education and day-to-day laboratory tasks in science and
industry�
They are designed to be used exclusively indoors�
Cubis models can be operated as standalone, connected to a
PC, or on a network�
General View of the Equipment and Equipment Supplied
Balances with a readability of ≤1µg
Pos� Description
1 Weighing pan
2 Filter weighing pan d50 mm
3 Internal draft shield (for MSx2�7S-F only)
4 Optional weighing pan d75 mm
5 Shield disk
6 Optional filter weighing pan d90 mm
7 Shield plate
8 Level indicator
9 Leveling foot
10 MSE2�7�� model: bush
11 Draft shield cover
Pos� Description
12 Female connector for weigh cell
13 DC jack
14 Display and control unit
15 Serial communications port (PERIPHERALS)
16 Slot for optional interfaces, e�g� 9-pin data output or Bluetooth�
PS2 socket has no function�
17 Lug for attaching antitheft locking device
18 Equipotential bonding conductor terminal
19 Equipotential bonding conductor terminal
20 Draft shield
Not shown: AC adapter, USB cable
Use 6971987
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
7
1
3
20
10
10

General View of the Equipment and Equipment Supplied
General View of the Equipment
and Equipment Supplied
Analytical and precision balances with a weighing range of up to 15 kg
Item Description
1 Upper sliding draft shield panel/Handle
2 Back panel
3 Weighing pan
4 Pan support (not for MSx225���/MSx125��� models)
5 Shield plate
6 Pan retainer
7 Right sliding panel/Handle
8 Leveling foot
9 Display
10 Display and control unit
11 Draft shield/Shield disk (only for models with a readability of
1 mg and 10 mg)
12 Below-cell weighing port
(on the bottom of the balance)
13 Leveling foot
14 Level indicator
15 Power socket
16 Slot for attaching an
anti-theft locking device
17 USB socket for a PC connection
18 Below-cell weighing hook
19 Slot for optional interfaces,
e�g�, 9-pin data output (as shown) or Bluetooth�
PS2 socket has no function�
20 Communication port (PERIPHERALS) for accessories
21 Menu access switch
22 Left sliding panel/handle
23 Semi-microbalances: Female connector for weigh cell
24 Semi-microbalances: Electronics module
(for MSx225���/MSx125��� models)
Not shown:
– AC adapter
– USB cable
– Operating instructions
– In-use cover over the display unit
– Dust cover (only for balances with a draft shield)
– In-use cover for housing (only for models with a readability of
19 mg/100 mg and a weighing capacity of <14 kg)
Cubis MSE Operating Instructions 7
9
10
22
3
4
5
5
6
6
12
12
10
10
13
13
6
11
11
4
3
3
14
15
16
17
18
19
20
21
4
23
24
14
16
19
20
21
1
2
3
4
5
6
7
8

8Cubis MSE Operating Instructions
General View of the Equipment and Equipment Supplied
Equipment Supplied and General View of the Equipment
Balances with a weighing range of 20 kg or more
1
3
4
5
7
2
6
Pos� Bezeichnung
1 DC jack
2 Leveling foot
3 Level indicator
4 Serial communications port (PERIPHERALS)
Pos� Bezeichnung
5 USB interface for PC connection
6 Display and control unit
7 Weighing pan
Not shown: AC adapter, USB cable

Cubis MSE Operating Instructions 9
Getting Started
Getting Started
Unpacking the Equipment
tOpen the packaging at the top�
tUse both hands to lift the balance, with the packaging, out of the cardboard
box�
tPlace the packaging with the balance on the floor�
tRemove the top part of the packaging�
Installation Instructions
tSelect the proper setup location:
– Set up the device on a stable, even surface that is not exposed to vibrations
(e�g� weighing stone)�
– Place the device in a location with enough free space around it so that
excessive heat cannot build up�
– Maintain free access to the device at all times�
Choose a location that is not subject to the following negative influences:
– Heat (heater or direct sunlight)
– Drafts from open windows, AC systems and doors
– Extreme vibrations during weighing
– Excessive moisture
Acclimatization
Condensation from humidity can form on the surfaces of a cold device when it is
brought into a substantially warmer area�
To avoid the effects of condensation, condition the balance for about two hours at
room temperature, leaving it unplugged from the power supply�
Carefully read all warnings and safety precautions in the respective section of this
manual�
°C

Getting Started
Balance with Draft Shield
tRemove the packages (containing draft shield panels, weighing pan, pan
support, AC adapter, etc�) from the lower packaging and place them to one
side�
tUse both hands to lift the balance out of the packaging�
3Exercise caution to avoid glass breakage� Never lift the equipment by the draft shield panels to remove it from the
packaging�
tPlace the balance on an even surface�
Balance with No Draft Shield
tUse both hands to remove the model without a draft shield from the
packaging�
tRemove the AC adapter and the balance parts from the packaging�
10 Cubis MSE Operating Instructions

Getting Started
Cubis MSE Operating Instructions 11
Assembly
Installing the Analytical Draft Shield Labeled DA, DI, and DU
Assembling the Balance
tFit parts onto the balance as shown in the picture�
1. Shield plate
2. Pan support (not for MSx225���/MSx125��� models)
3. Weighing pan
tSlide the upper draft shield panel into the guide rails from the rear�
tSlide the left and right draft shield panels into the guide rails from the rear�
Make sure the panels are within the upper and lower guide rails�
tSlide the panels in until they engage�
1. Right draft shield panel
2. Left draft shield panel
yThis completes the balance assembly�
2
1
3

Getting Started
2
1
3
2
1
3
Installing the Draft Shield Labeled DE for Milligram Balances
Assembling the Balance
tFit parts onto the balance as shown in the picture�
1. Shield plate
2. Pan support
3. Weighing pan
Assembly of Milligram Balances without Glass Draft Shield (DR Option):
Balance Assembly
tFit all components listed below onto the balance in the order given:
1. Pan support (see also next section)
2. Shield plate
3. Weighing pan
4. Draft shield frame
tFirst insert the shield plate�
tMake sure the pin on the pan support is facing toward the front, and slide it
under the clip on the pan retainer�
1. Insert the pan support�
tAfter inserting the pan support, press it down against the shield plate so that it
lies flat�
3
Exercise caution to avoid pinching or crushing fingers�
2. Press down the pan support�
tPlace the weighing pan on the pan support�
3. Weighing pan
1
2
3
4
12 Cubis MSE Operating Instructions

Getting Started
Cubis MSE Operating Instructions 13
tSlide the upper draft shield panel into the guide rails from the rear while
pressing the locking tab�
tSlide the side draft shield panel into the guide rails from the rear while pressing
the locking tab�
yThis completes the balance assembly�
tRemove the panel again if necessary
1. Press on the locking tab�
2. Remove the panel again if necessary
tPlace the panel in the storage slot at the back of the balance�
Assembly for Precision Balances without Draft Shield with a Weighing Range
up to 15 kg
tFit parts onto the balance as shown in the picture�
1. Pan support
2. Shield plate/Draft shield
3. Weighing pan
tPlace the pan support diagonally and press down lightly�
1. Pan support
2
1
2
1
2
1
3
1

Getting Started
tCarefully turn the pan support clockwise until the two buttons engage�
The pan support is now attached�
t2. Insert the shield plate/draft shield�
t3. Place the weighing pan on the pan support�
yThis completes the balance assembly�
Models with a Weighing Range from 20 kg Upwards:
tPlace the weighing pan on the balance�
2
3
14 Cubis MSE Operating Instructions

Getting Started
Cubis MSE Operating Instructions 15
Connecting the Weigh Cell to the Electronics Module/Evaluation Unit
tConnect the weigh cell and electronics module using the connection cable�
Make sure that the connectors click into place so that both ends are securely
connected�
3Please check the plug contacts to ensure a proper connection�
There should be no tension on the connection cable�
We therefore recommend placing the device close to the wall�
tConnecting the Weigh Cell to the Evaluation Unit
Make sure that the connectors click into place so that the connection is secure�
3Models with a separate electronics module (e�g� MSE6�6/3�6/2�7),
MSE225S/P and MSE125P: Do not replace the electronics module�
Replacing them with models from the ME/SE series, for example, can
damage the device�
Microbalances (Models MSE6.6S/3.6P/2.7S):
Placing Components on the Weigh Cell
tInstall the following parts in the order listed:
1� MSE2,7S models: bush
2� Shield plate
3� Weighing pan
Note: After inserting the weighing pan, turn it slightly to the left and right,
while pressing it down lightly�
4� Internal draft shield (for MSE2�7S only)
5� Draft shield: Center the hole over the pan (see arrows)
Filter Balances (Models MSE6.6S-F/2.7S-F):
Placing Components on the Weigh Cell
tPlace the components listed below inside the weigh cell in the order given:
1� MSE2,7S-F models: female connector
2� Shield plate
3� Internal draft shield
4� Filter weighing pan d50 mm or weighing pan
(optional filter weighing pan d75 mm or d90 mm)
Note: After inserting the pan, turn it slightly to the left and right,
while pressing it down lightly�
5� Draft shield cover
! Tip: Turn the balance off and then on again after replacing the pan during
operation�
3
2
4
5
1
MSE6�6S/3�6P/2�7S:
MSE225…, MSx125:
MSE6�6S-F/2�7S-F:
MSE6�6S/3�6P/2�7S:

Getting Started
Setting up a filter weighing pan for left-handed users:
tRemove the draft shield cover
tUnscrew the pin and move from the right to the left side
tTurn draft shield parts approx� 90 degrees to the left (loosen knurled screw)
Power Connection
tCheck the voltage rating and plug design�
– Make sure that the voltage rating printed on the manufacturer’s ID label is
identical to that of your local line voltage�
– If the stated supply voltage or the plug design of the power cord does not
comply with your country’s standard, please inform the nearest Sartorius
representative or your dealer�
– The power connection must be made in accordance with the regulations
applicable in your country�
– In order to connect the equipment to the power supply (protection class 1), use
a suitable, correctly installed wall outlet with a protective grounding conductor
(PE) and a fuse of a maximum 16 A�
– If a main feeder from the ceiling is required or if installation of a CEE plug is
necessary, these must be carried out by a qualified electrician�
– Only use original Sartorius AC adapters�
16 Cubis MSE Operating Instructions

Getting Started
Cubis MSE Operating Instructions 17
Transporting the Balance
Transporting the Device over Short Distances
3Exercise caution to avoid glass breakage�
Never lift and carry the balance by its draft shield�
tCarry as shown in the illustration�
or
tCarry as shown in the illustration�
Storage and Shipping Conditions
– Permitted storage and shipping temperature: -10 to +60 °C
– Unpacked devices can lose their precision if subject to extreme vibrations�
– Excessive vibrations may compromise the safety of the equipment�
Save the packaging for any future storage or shipment of the balance�
Only the original packaging provides optimum protection for the equipment�
– Follow all warnings and safety precautions�
– Follow the instructions in the chapter: “Transporting the Balance�"

Getting Started
Analytical and precision balances:
1. Plug the DC supply cable of the AC adapter into the power socket of the
balance and tighten the threaded fitting�
Balances with a readability of ≤0�01mg
1. Plug the DC supply cable of the AC adapter into the power socket of the
electronics module and tighten the threaded fitting�
2. Plug the other end of the power cord into the AC adapter�
3. Insert the AC adapter power plug into the wall outlet�
yThe balance is now ready to use�
Safety Precautions
The output line of the adapter has a terminal (GND) connected to the metal
housing of the balance� The data port is also galvanically linked to the balance
housing (GND)�
18 Cubis MSE Operating Instructions
2
1

Getting Started
Cubis MSE Operating Instructions 19
Leveling the Balance, Setting the Level Indicator
hLeveling the balance compensates for slant or unevenness at the place
of installation� The balance must be perfectly horizontal to ensure
consistent, reproducible weighing results� All models are equipped with
an electronic tilt angle detection feature� If the balance is not level,
a warning symbol is shown on the display� Push-button automatic
leveling is available on models with motorized leveling feet� For models
with manual leveling feet, please follow the instructions on the display:
see “Leveling the Balance with the Inclination Sensor�"
Leveling the Balance Manually
tThe balance is leveled using both front leveling feet�
tScrew in both back leveling feet (only for models with back leveling feet)�
tTurn the two front feet as shown in the illustration until the air bubble is
centered within the circle of the level indicator�
yNormally, several leveling steps are required�
tScrew out both back leveling feet until they touch the setup surface
(only for models with back leveling feet)�
Warm-up Time
yIn order to deliver the precise results described in the Technical Specifications,
the balance must warm up for at least 30 minutes after initial connection to
the power supply� Only after this time will the device have reached the required
operating temperature�
When a verified balance used in legal metrology (legal-for-trade
applications) is connected to the power, it must warm up for at least
two hours before operation�
R
L
L
LR
R
12
6
93
2

Getting Started
Connecting Electronic Devices (Peripherals)
tMake absolutely sure that the device is unplugged from the power supply
before connecting/disconnecting any peripheral device (printer, scanner, PC) to
or from the data port�
3A device connected to the power supply should never be opened�
Anti-theft Locking Device (Accessory)
Balances with a readability of ≤0�01mg
tAn anti-theft locking device can be installed to the back of the balance if
required�
Balances with a readability of ≤1µg
To fasten an antitheft locking device, use the lug located on the back of the weigh
cell�
20 Cubis MSE Operating Instructions